The effect of agitation on the dispersion of organic phase was investigated in an immiscible liquid system (n-hexane/40 wt % p-TSA aqueous solution). Four different types of six-bladed turbine impellers were used : a flat blade type and three screen blade types. The experimental results showed that the extent of dispersion of organic phase at the same agitation speed was decreased in the order of flat blade, 60 mesh, 40 mesh, and 20 mesh screen blades. Otherwise, it was increased with increasing the concentration of TBA as a surfactant agent and with decreasing volume fraction of organic phase. Also, the minimum agitation speed for a complete dispersion was increased in the order of flat blade, 60 mesh, 40 mesh, and 20 mesh screen blades. However, the minimum power consumption did not vary significantly. In this condition, the relationship between Power number and Reynolds number was expressed as $N_p=a\;N_{Re}{^b}$, where the values of constant a and constant b were ranged 2200~4100 and -0.69~-0.63 respectively.
Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
/
1991.11a
/
pp.34-37
/
1991
Al계 베어링합금은 소착저항력등의 베어링특성이 우수하여 최근에 자동차의 엔진부품에 많이 사용되고 있다. Al계 베어링합금으로는 Al-Sn계, Al-Pb계, Al-Si계 합금이 개발되어 사용되어 왔다. Al-Si계 합금은 높은 강도, 우수한 부식성, 주조성이 향상되는 장점등을 갖고 있다. 또한 Al-Pb계 합금은 Pb가 고체윤활제로 작용하여 소착저항성이 높으며 가격도 저렴한 장점을 갖고 있다. Al과 Pb는 용융상태에서 넓은 용융간극을 갖어 중력편석을 일으키기 때문에 일반적인 주조방법으로 Al계 베어링합금을 제조할 수없다. 또한 Al에 Si이 첨가됨에 따라 높은 경도등의 기계적성질의 향상이 얻어지지만 Al 기지에 Si의 함량이 증가할 수록 편석이 심해져 조대한 Si-rich상이 미세조직에 존재하여 합금이 취약해지는 단점을 갖고 있다. 따라서 본 연구에서는 Al 기지에 Pb의 중력편석을 최소화하고 Al 기지에 조대한 Si-rich상이 생성되는 것을 막기 위하여 Al과 Pb가 공존하는 온도구역에서 높은 교반속도로 용탕을 강제교반하여 액상에서 Pb와 Si을 미세하게 분산시킨 후 수냉되는 동주형에서 급속응고시켜 Pb와 Si-rich 상이 균일하게 분포된 Al계 베어링합금을 제조하였다. 본 연구에서는 Pb의 양을 0%에서 35%까지 변화시켰으며, Si의 양을 0%에서 20%까지 변화시켜서 베어링합금을 제조하였으며, 강제교반속도는 500rpm에서 2500rpm 까지 변화시켜 베어링합금을 제조하였다.
Journal of the Korean Society of Propulsion Engineers
/
v.16
no.3
/
pp.16-23
/
2012
This study has been conducted to scrutinize agitation effects of an ultrasonic standing wave on the dynamic behavior of methane/air premixed flame. The propagating flame was caught by high-speed Schlieren images, through which local flame velocities of the moving front were analyzed in unprecedent detail. It is revealed that the propagation velocity agitated by the ultrasonic standing wave is greater than that without agitation at the stoichiometric ratio: the velocity enhancement diminishes as the equivalence ratio approaches upper flammability limit or lower flammability limit. Also, vertical locations of the wave-affected frontal distortions do not vary appreciably, unless the propagating-mode characteristics (pressure amplitude and driving frequency) of ultrasonic standing wave were not changed.
In order to determine the optimal conditions for the process of acetic acid fermentation, the kinetics of Acetobacter aceti fermentation in submerged batch cultures were studied at different agitation speeds and air flow rates. The maximum cell concentration was noted after about 48 hr fermentation and the time course of Acetobactey aceti fermentation showed a distinct feature of growth-associated product formation. At agitation speeds 700, 500, and 300 rpm fixed on air flow rate 1 v/v/M, specific grow rates were $3.97\times10^{-2},\;3.82\times10^{-2},\;and\;2.04\times10^{-2\} \;hr^{-1}$, saturation constants were 61.4, 64.6, and 69.4mg/ml. and volumetric oxygen transfer coefficients were 0.9337, 0.4468, and 0.1701 $min^{-1},$ respectively. At air flow rates 1.25, 1.00, and 0.75 v/v/M fixed on agitation speed 500 rpm, specific growth rates were $3.90\times10^{-2},\;3.82\times10^{-2},\;and\;2.37\times10^{-2}\;hr^{-1}$, saturation constants were 63.4, 64.6, and 64.9 mg/ml, and volumetric oxygen transfer coefficient were 0.4923, 0.4468, and 0.3509 $min^{-1},$ respectively.
Journal of the Korea Academia-Industrial cooperation Society
/
v.18
no.11
/
pp.124-129
/
2017
In this study, we report characteristics of friction stir welding (FSW) technique applied to Al-6005-T6 extruded sheets, which is a common material for railway car bodies. With the welding speed fixed at 300 mm/min, the revolution per minute (RPM) of the rotating tool was varied from 600 to 1800 RPM, with the aim at evaluating the resultant microstructure and mechanical behaviors. Comparison is also made with the conventional Metal Inert Gas (MIG) welding technique. Unlike MIG, no micro-voids were observed for FSW specimens. Hardness measurement revealed that the increased heat input by increasing RPM results in widened heat affected zone (HAZ) and decreased hardness for HAZ due to grain coarsening. Hardness results for the nugget do no show difference. During tensile tests, specimens fractured at HAZ, and increasing rpm led to decrease of the yield stress and tensile stress for the selected RPM range, which is considered to be due to the grain coarsening for HAZ.
Friction stir welding was first reported by TWI(The Welding Institute) in 1991, and this welding method has been rapidly used in various industrial areas such railway, automobile, aerospace and shipbuilding industry. Here, we study core characteristics of friction stir welding (FSW) applied to Al 6005-T6 extruded sheets, which is the typical alloy used for railway car bodies. With the fixed welding speed of 500 mm/min, the rotating tool speed was varied from 600 to 1800 RPM. The results of hardness measurement revealed that the hardness of nugget area is ~70% with respect to the parent material, and for the selected range of rotation speed, no clear dependence was observed and the hardness values close to the parent materials were achieved for the area located 5 mm away from the welding interface. The tension test shows that yield strength and tensile strength were slightly decreased with increasing RPM, with no observed difference for the elongation.
The effects of environmental and compositon factors, such as reaction time, metal ions, pH, agitation speed, the weight ratio of water to oil, and the weight of enzyme, on the hydrolysis of oils by Lipase-OF were investigated. In case of oils with low melting point, the optimum temperature of hydrolysis were the enzyme activity was maximum was 37$^{\circ}C$. However, when the melting temperature was higher than 4$0^{\circ}C$, the optimum temperature was around the fusion temperature. The activity of Lipase-OF decreased very rapidly with increase of temperature in the range of higher than 45$^{\circ}C$ and the activity perished above $65^{\circ}C$. The effect of agitation speed was investigated from 150 to 650 rpm. The hydrolysis of oils increased as the agitation speed increased up to 350 rpm, but it did not increase any more above 350 rpm. The weight ratio of water to oil was changed from 1 : 9 to 9 : 1 for the investigation of the effect on the hydrolusis. The weight ratio for maximum hydrolysis was 1 : 1. $Ca^{2+}\;and\;Mg^{2+}$ among various metal ions had some effect on the stimulation of hydrolysis. The optimum concentration of the ions was about 100ppm at which the hydrolysis increased, compared with that of distilled water, by 2 to 3%. The Optimum pH of Lipase-OF was 7. The hydrolysis decreased as the pH decreased as the pH decreased and also decreased as the pH increased. The content of enzyme affected the hydrolysis of oil. The hydrolysis increased with the content of Lipase-OF in the range of less than 0.013 wt% of substrate. However, the increase of hydrolysis with the content of Lipase-OF ceased above 0.013 wt%. The experiments investigating the effect of environmental and composition factors on the hydrolysis of oils showed that the optimum temperature was 37$^{\circ}C$, the pH 7, the concentration of $Ca^{2+}\;or\;Mg^{2+}$ 100 ppm, the agitation speed 350 rpm, the weight ratio of water to oil 1 : 1, and the content of Lipase-OF 0.013 wt% of substrate.
Minseon Park;Minjung Jung;Noh-sup Lee;Soochul Rhee;Namhoon Lee
Journal of the Korea Organic Resources Recycling Association
/
v.32
no.2
/
pp.5-14
/
2024
A study approached the development of a process for efficiently recycling discarded cigarette butts, reported as a major source of microplastic pollution in aquatic environments. Cigarette butts were sorted to extract filters, and cellulose acetate, the raw material of the filters, was extracted to a high degree of purity. The sorting of filters from cigarette butts was conducted through both wet and dry processes, each with optimized sorting conditions. Wet stirring sorting considered factors such as solid-liquid ratio, stirring speed, and stirring temperature. The highest efficiency of wet stirring sorting, at 46.21%, was observed with a solid-liquid ratio of 1:45, stirring speed of 200 rpm, and stirring temperature of 50℃. Dry wind power sorting took into account moisture content and residence time. The filter sorting efficiency reached its peak at 57.10% with a moisture content of 20% and a residence time of 5 minutes. There was no significant difference in the recovery rate of cellulose acetate between the two sorting processes. Dry wind power sorting was deemed a more advantageous process in terms of energy and environmental considerations within the scope of this study.
Proceedings of the Korea Association of Crystal Growth Conference
/
1997.10a
/
pp.51-55
/
1997
이트륨 옥살레이트 결정화에 있어서 반응물의 농도, 반응 온도, 반응물의 주입속도 변화등의 반응조건(reaction condition)의 변화와 반응기 내에서의 교반속도와 같은 hydrodynamic condition의 변화가 생성된 옥살레이트 결정의 입자크기, 결정형태등에 미치는 영향을 체계적으로 관찰하였다. 그리고 agglomeration의 영향에 의한 particle의 크기변화에 있어 생성물의 과포화는 agglomerates를 결정 짓는 가장 중요한 변수이다. 또한 반응성 결정화에 의해서 얻어진 Yttrium Oxalate가 온도 변화에 따라서 Yttrium Oxide로 열분해되는 온도구간과 결정구조의 변화 및 분자 구조의 변화를 관찰하여 최종의 Yttrium Oxide가 생성되는 것을 확인하였다.
Park, Sang-Wook;Moon, Jin-Bok;Ko, Myung-Sook;Kim, Gun-Woo
Applied Chemistry for Engineering
/
v.3
no.1
/
pp.119-129
/
1992
The rates of mass transfer with the alkaline hydrolysis of ethyl acetate and n-butyl acetate were measured by using a modified Lewis cell. The rates of mass transfer with chemical reaction were independent of the speed of agitation, and the reaction enhancement factors were independent of the ionic strength. The second order reaction rate constants of ethyl acetate and n-butyl acetate could be obtained from an approximate solution of a diffusion equation by film theory, and their values were $0.041m^3/kg\;mol{\cdot}s$ and $0.338m^3/kgmol{\cdot}s$, respectively.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.