• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.254-254
• /
• 2009

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.409-414
• /
• 2013

In this work, corrosion of 304 stainless steel was evaluated by using acoustic emission(AE) technique. AE measurement system was set for detecting acoustic signal during accelerated corrosion test of the specimen. AE signal started to be detected after the time of pitting corrosion initiation was evaluated by anodic polarization curve. Pitting corrosion damage was confirmed by optical microscopic observation of the surface morphology. AE cumulative counts and amplitude according to corrosion time could be divided into three stages. These trends were discussed in relation with changing pitting corrosion mechanism. Feasibilities of AE technique for evaluation of corrosion damage and mechanism were suggested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.472-472
• /
• 2013

본 논문은 InN와 GaN를 교대로 증착하는 교번성장법을 이용해 제작한 4주기 InN/GaN 박막의 구조적, 광학적, 특성을 X-ray diffraction, Atomic force microscopy, Transmission electron microscopy과 저온 Photoluminescence (PL) 장비를 사용하여 분석한 결과를 보고한다. Fig. 1은 4주기 InN/GaN박막의 XRD 스펙트럼으로 GaN(0002)와 InN(0002)의 회절 신호를 관찰할 수 있다. 그러나 두 피크뿐만 아니라 InN와 GaN 사이에 구분이 되지 않은 추가 신호를 확인할 수 있다. 추가신호는 InN와 GaN 계면에서 발생하는 상호확산 확률로서 해석할 수 있다. Fig. 2는 다양한 조건에서 성장한 InN/GaN 시료의 PL스펙트럼으로 방출 파장은 각각 1,380, 1,290, 1,280, 1,271, 1,246 nm로 측정되었다. 성장 조건 변화에 따른 발광특성 변화를 박막에서 III족 원자 특히, In 원자의 성장 거동에 따른 구속준위(Localized states) 변화로 논의할 예정이다.

• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.235-240
• /
• 2023

The optical signal injected into an end-fire optical phased array propagates along the waveguides inside the device and is emitted from the edge of the antenna. In general, reflection and scattering occur at the boundary, thereby reducing the emission efficiency of the optical signal. In this article, we propose a silicon nitride (Si₃N₄) tapered waveguide antenna structure whose width is tapered toward the emitting edge, achieving high emission efficiency operating at the 1,550 nm wavelength. The Si₃N₄ tapered waveguide antenna was numerically designed using the 3D finite-difference time-domain method. The optical signal emission efficiency increased from 78% to 96.3%, while reflectance decreased from 22% to 3.7% compared with the untapered waveguide antenna counterpart. This result will not only boost the optical signal intensity but also mitigate optical noise resulting from back reflection along the waveguide in the end-fire optical phased array device.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.4
• /
• pp.274-286
• /
• 2005

Fracture behaviors and acoustic emission (AE) characteristics of single-edge-notched monolithic aluminum plates and glass fiber/aluminum hybrid laminate plates have been investigated under tensile loads. AE signals from monolithic aluminum could be classified into two different types: signals with low frequency band and high frequency band. High frequency signals were detected in the post stage of loading beyond displacement of 0.45mm. For glass fiber/aluminum laminates, AE signals with high amplitude and long duration were additionally confirmed on FFT frequency analysis, which corresponded to macro-crack propagation and/or delamination between A1 and fiber layers. On the basis of the above AE analysis and fracture observation with optical microscopy and ultrasonic T scan, characteristic features of AE associated with fracture processes of single-edge-notched glass fiber/aluminum laminates were elucidated according to different fiber ply orientations.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.418-428
• /
• 2003

Fiber fracture is one of the dominant failure phenomena affecting the total mechanical Performance of the composites. Fiber fracture locations were measured through the conventional optical microscope and the nondestructive acoustic emission (AE) technique and then were compared together as a function of the epoxy matrix modulus and the fiber surface treatment by the electrodeposition method (ED). Interfacial shear strength (IFSS) was measured using tensile fragmentation test in combination of AE method. ED treatment of the fiber surface enlarged the number of fiber fracture locations in comparison to the untreated case. The number of fiber fracture events measured by the AE method was less than optically obtained one. However, fiber fracture locations determined by AE detection corresponded with those by optical observation with small errors. The source location of fiber breaks by AE analysis could be a nondestructive, valuable method to measure interfacial shear strength (IFSS) of matrix in non-, semi- and/or transparent polymer composites.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.42-46
• /
• 1997

In order to acquire the fluorescence burst signals emitted from single dye molecules that pass through a detection space defined by a confocal microscope, a computer-interfaced photon counter has been fabricated. The maximum count rate is about 80 MHz, which is limited by the counter devices used. Using both the operating computer program written by BASIC and the 486 PC computer, the minimum bin-width of 25 $mutextrm{s}$ has been achieved. The characteristics of fluorescence burst signals emitted from JA22 molecules at about 1$\times$$10^{-11}$m mol/L in ethylene glycol are discussed briefly.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.259-264
• /
• 1999

The relationship is derived for color CRT display system between the spectral radian existence emitted and digital inputs. The amount of spectral radiant existence depends on the characteristics of the video board, electric circuits, and CRT as well as digital inputs. Especially, the function of this relationship changes as the amplifier gain and offset voltage of electric circuits. In this study, we set the test display system on the optimum state which satisfies gun independence characteristics by using the contrast and the brightness controls of display. Temporal stability, special uniformity, and color distinction of CRT display system are evaluated at the optimum state. Also contrasts in dark room and illuminated room are compared.

• Composites Research
• /
• v.16 no.1
• /
• pp.26-33
• /
• 2003

Utilizing a thermo-acoustic emission (AE) technique, a study on detection and evaluation of microfractures in cross-ply laminate composites was performed. Fiber breakages and matrix fractures formed by a cryogenic cooling at $-191^{\circ}C$ were observed with ultrasonic C-scan, optical and scanning electron microscopy. Those microfractures were monitored in a non-destructive in-situ state as three different types of thermo-AE signals classified on the basis of Fast-Fourier Transform and Short-Time Fourier Transform. Thus, it was concluded that real-time estimation of microfracture processes being formed during cryogenic cooling could be accomplished by monitoring such different types of thermo-AEs in each time-stage and then by analyzing thermo-AE behaviors for the respective AE types on the basis of the AE signal analysis results obtained during thermal heating and cooling load cycles.

• Korean Journal of Optics and Photonics
• /
• v.11 no.1
• /
• pp.37-42
• /
• 2000

We have numerically solved rate-equations of semiconductor optical amplifier (SOA) to understand the characteristics of SOA. The rate-equations we have used can describe injection carrier density, amplified spontaneous emission and signal photon density in spatial and time domain by dividing the cavity into multi-section. We have investigated injection carrier density, amplified spontaneous emission and signal photon density as a function of position and time in the case of single channel input in the form of square pulse. Also we have analyzed the non-linear phenomena of SOA in the case of injecting multi-channel wavelengths as in WDM. Intermodulation distortion (IMD) caused by beat among channels has significant effects on the signal distortion as the channel spacing becomes narrower, and channel crosstalk becomes larger as the power of signals increases. In the case of the injection of another CW laser whose wavelength is far enough from the signal wavelengths, the crosstalk and the output signal distortion can be significantly reduced. duced.