• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.89-97
• /
• 2020

In this study, a numerical analysis was performed on 26 inch single and coaxial propeller using the ANSYS Fluent 19.0 Solver to analyse the effect of the distance between coaxial propellers as one of the design parameter. The Moving Reference Frame (MRF) method was used for single propeller, while the sliding mesh method was used for a coaxial propeller to analyse the flow field varying with azimuth angle. The thrust and power are decreased as the upper and lower propeller approaching each other. As H/D is increased, interference between the propellers is decreased. According to the flow field variable contour of the coaxial propeller, it appears that the change in aerodynamic performance is due to the loading effect and the tip vortex wake effect.

• Journal of the Korea Society for Simulation
• /
• v.26 no.1
• /
• pp.13-19
• /
• 2017

6-DOF flight simulation program is most generally used M&S tool in domestic missile development procedure. The 6-DOF M&S method, however, cannot validate the performance of a imaging seeker-adopted missile in various conditions. A M&S tool for the analysis of the integrated-flight simulation is required since the tracking performance of the imaging seeker is highly dependent on the missile maneuvering, which introduces the displacement and rotation of the target in the seeker imagery. Through the development of the $3^{rd}$ generation anti-tank missile, Raybolt, the integrated-flight M&S tool was developed and applied to the missile configuration design. It integrates synthetic image generation S/W, imaging tracker, and flight simulation program and computes the main system performance criteria, hit probability by Monte-Carlo Simulation. In this paper, the issues in the $3^{rd}$ generation anti-tank missile configuration and the integrated-flight M&S method and results are described.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.253-256
• /
• 2003

The engine core of a 65hp-turboshaft engine for UAV is developed and modified into a 55lbf-turbojet engine. Since the core engine is installed with a propelling nozzle, which has the same mass flow characteristics as the power generator of the turboshaft engine its mechanical and aerodynamic characteristics are basically the same as those of the complete engine. Engine output is not shaft power but thrust force that is easier to measure. The core engine is very useful for core test purpose. Besides, the core engine itself can be directly used for propulsion of small air vehicles.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.331-335
• /
• 2006

Theoretically, stable operations of an inlet are achieved at the design condition. However, at off-design conditions supersonic inlets often encounter the problem of aerodynamic instability, called inlet buzz. During inlet buzz, supersonic inlets exhibit considerable oscillation of the shock system in front of the inlet and corresponding large pressure fluctuations downstream. This phenomenon results in decrease of engine performance. An experimental and numerical study was conducted to investigate the phenomenon of supersonic inlet buzz on a generic, axisymmetric, external-compression inlet with a single-surface center-body. This study suggest that intermittent buzz exist and the frequency become to be large as increasing the back pressure.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.40-47
• /
• 2008

The turbulent flow characteristics around a small-size axial fan(SSAF) for a refrigerator are strongly dependent upon the operating points. Four operating points such as $\phi$ =0.1, 0.18, 0.25 and 0.32 were adopted in this study to investigate three-dimensional turbulent flow characteristics around the SSAF by using a fiber-optic type Laser Doppler Anemometer(LDA) system. Downstream mean velocity profiles of the SSAF along the radial distance show that axial and tangential velocity components exist predominantly, except $\phi$ = 0.1, and have a maximum value at $r/R{\fallingdotseq}0.8$, but radial velocity component having a relatively small value only turns flow direction to the outside or the central part of the SSAF. The turbulent intensity shows that the radial component exists most greatly after $r/R{\fallingdotseq}0.5$. Downstream turbulent kinetic energy at $\phi$ = 0.25 and 0.32 together has the largest peak value at $r/R{\fallingdotseq}0.9$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.69-75
• /
• 2009

This paper studies the aerodynamic performance that the vent mixer-new conceptual supersonic mixer-showed with its geometric characteristics. The hole is 2 mm with 2 mm's distance from the wall in case 1 and with no distance in case 2. In case 3 die hole is 1 mm. Case 1 and case 2 showed the same total pressure recovery ratio, of which the case 3 was lower than that. While cases 1-3 had the same reattachment length, the shear layer was thicker in cases 1 and 2 than in case 3. Within the recirculation zone, cases 1 and 2 had lower pressure loss and higher velocity gradient difference than case 3-they enhance mixing between air and fuel. Separation bubble which is developed by the inflow into the recirculation zone has a significant effect on the total pressure recovery ratio in the combustor. Also separation bubble influences pressure distributions and recirculation flows in the recirculation zone. Therefore, inflow rate of air into the recirculation zone mainly affects the performance of vent mixer.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.159-166
• /
• 2018

In this study, the internal structural design, dynamic characteristics and load analyses of the small scaled rotor blade required for LCH(Light Civil Helicopter) main rotor wind tunnel test were carried out. The test is performed to evaluate the aerodynamic performance and noise characteristics of the LCH main rotor system. Therefore, the Mach-scale technique was appled to design the small scaled blade to simulate the equivalent aerodynamic characteristics as the full scale rotor system. It is necessary to increase the rotor speed to maintain the same blade tip speed as the full scale blade. In addition, the blade weight, section stiffness, and natural frequency were scaled according to the Mach-type scaling factor(${\lambda}$). For the design of skin, spar, torsion box, which are the main components of the blade, carbon and glass fiber composite materials were adopted, and composite materials are prepreg types that can be supplied domestically. The KSec2D program was used to evaluate the section stiffness of the blade. Also, structural loads and dynamic characteristics of the Mach scale blade were investigated through the comprehensive rotorcraft analysis program CAMRADII.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.46-52
• /
• 2008

The instrumentation was studied in order to measure aerodynamic performance and efficiency of a compressor as a component of a 5MW-class gas turbine for power generation. In case of an axial compressor, the distributions of static pressure on a casing can be obtained by averaging at each stage and those of total pressure and temperature in the flow field of the compressor can be measured with a Kiel temperature probe. In case of a centrifugal compressor, the static pressures at the hub and the tip, respectively, of an impeller exit are considerably different, so the pressures need to be measured at both positions and thereafter averaged. The distributions of static pressures in a diffuser and a deswirler are measured at ten positions along five streamlines in one pitch. In addition the flow field can be measured in detail by 5-hole Pitot tube in order to analyze the flow characteristics of the core flow region and wake region and the rotor-stator interaction of the compressor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.520-529
• /
• 2016

The main purpose of this study was to analyze the performance of a medium-altitude long endurance unmanned aerial vehicle through reverse-engineering method. The external configuration data of the RQ-1 Predator was reverse-engineered from related photos and specification data available on public domains, which also were used to generate the CATIA modeling and weigh distribution data of the UAV. The aerodynamic characteristics of RQ-1 Predator were mainly predicted the vortex lattice method and an empirical method, which the propeller performance was analyzed by the empirical method proposed by Howe. The rate of climb, service ceiling, range, and the loiter endurance of the UAV was analyzed, which showed good agreement with the reference data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.83-94
• /
• 2000

A systematic humidity correction technique that can be used for any type of engine control mode is developed to predict the variation of engine performance due to inlet humidity. Limitation of conventional method is rot identified and then, a new method is proposed to take into account the humidity effects on each engine component characteristics and to find the variation of equilibrium running point through a re-match process between the components with a given engine control variable depending on the humidity of inlet. Comparisons are made between two methods for a single spool gas turbine engine, and it was found that the conventional method leads to invalid correction when a physical variable such as rotational speed is controlled for engine operation in humid environment. It was also found that the accuracy of the conventional method depends on the engine control mode and the engine configuration whereas the proposed method can be used for any type of engine control mode and engine configuration.