• The Science & Technology
• /
• v.33 no.10 s.377
• /
• pp.10-12
• /
• 2000

더 빠르게... 더 높게... 이번 시드니올림픽에서 새로운 기록을 세우기 위해 선진국들은 스포츠 과학화에 많은 투자를 했다. 피로를 줄이는 수영복, 레이저 달린 소총, 공기저항 줄이는 보디슈트, 사이클의 실크타이어 등 미국이 동원한 첨단 스포츠과학기술을 소개한다.

• Journal of the Korea Convergence Society
• /
• v.10 no.9
• /
• pp.161-166
• /
• 2019

This study examines the flows near the different side mirrors by analyzing the flow due to air resistance at A, B and C models of automotive side mirrors. Model A is a square-shaped side-mirror. Model B is a triangular side-mirror and model C is an oval-shaped side-mirror. The air resistance of the side-mirror while driving is reduced and the automotive power can be reduced by changing the design of automotive side-mirror. As analysis result, as the pressure of air resistance against side mirror becomes larger, it can be seen that the air flow rate becomes great. Therefore, it can be estimated that the smaller the pressure of air resistance, the smaller the flow rate and the better the air flow. Therefore, it can be acknowledged that model B is the best model. As the design data of the automotive side mirror obtained on the basis of this study result are utilized, the esthetic sense can be shown while driving a car at real life.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.44-50
• /
• 2010

This study is devoted to understand the basic characteristics of the flowfield around a train in evacuated tube and to suggest an efficient numerical method to calculate the flowfield. To get steady-state solution in minimum calculation domain, various boundary condition have been tried for steady calculation and have been compared to the solution of unsteady calculation. At the train velocity of 300km/h, the aerodynamic drag results of both calculation method agreed very well. The drag ratio between on the open filed and in the tube from the calculation result by the suggested numerical method lied in the same fitting curve with that from the filed test of high-speed trains running in the line.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.61-61
• /
• 2017

노지 고추 수확작업은 100% 인력에 의존하고 있으며 7~9월에 걸쳐 5~6회의 다수의 작업이 수행되어 노동 강도가 크다. 또한 농촌의 고령화와 노동력 감소로 인하여 수확인력의 부족이 발생하고 있음에도 불구하고 시중에 유통되고 있는 고추 및 노지채소 수확작업 편이기기는 동력이 아닌 인력으로 이랑사이를 이동하며 작물을 수확하는 구조로 되어있다. 이는 노동 강도를 줄여주는 효과가 미미하기 때문에 동력이 수반된 편이장치가 필요하며 또한 적절한 모터 및 제어장치가 요구된다. 적절한 모터를 선정함에 있어서 영향을 주는 인자는 주행저항(RR)이며, 구성요소로는 구름마찰저항(Rr), 공기저항(RА), 등판저항(Rg), 가속저항(Ra)이 있으며, 다음과 같은 식으로 정의된다. 주행저항(RR)=구름마찰저항(Rr)+공기저항(RA)+등판저항(Rg)+가속저항(Ra) 구름마찰저항(Rr)=구름마찰저항계수(${\mu}$)${\times}$차량총중량(W) 등판저항(Rg)=차량총중량(W)${\times}Sin{\theta}$ 공기저항(RА), 및 가속저항(Ra)은 1m/s 미만의 속도가 요구되기 때문에 무시할 수 있다. 동력원에서 최종 구동축으로 전달된 동력은 주행장치를 통하여 지면에 전달되고 이 동력에 의해 작업차의 주행장치에 추진력이 발생하며 주행장치의 추진력이 주행저항 이상이 될 때 작업차는 전진하게 된다. 따라서 작업차의 주행속도를 V(m/s), 전동기의 효율을 ${\mu}_m$, 동력전달효율을 ${\mu}_{TD}$라고 하면 다음과 같은 식이 산출된다. 전동기의 소요출력(P)=주행저항(RR)${\times}$속도(V)/전동기의 효율(${\mu}_m$)${\times}$동력전달효율(${\mu}_{TD}$) 구름마찰계수를 0.3이라고 할 때 포장의 경사도와 작업차의 주행속도 변화에 따른 주행소요 동력을 비교하였다. 주행소요동력은 포장의 경사각과 주행속도의 증가와 더불어 증가한다. 고추 및 노지채소 수확작업 편이장치의 작업시 요구되는 주행속도는 일반적으로 0.25m/s, 등반각은 5도이다. 이때 구동 전동기의 출력은 안전율을 고려하여 식에 의해 계산한 결과 1ps으로 산출 되었다. 선정한 구동모터의 감속비는 7.18 : 1, 에너지의 효율은 78 %, 기동토크는14 N/m 이며, 축전지의 경우 구동모터에 기반 하여 구입이 간편하고 상용화 되어있는 연축전지를 사용하여 교체 및 수리가 간단하도록 하였다. 축전지는 12V 18Ah의 축전지 2개를 사용한다.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.8
• /
• pp.17-27
• /
• 2016

High-speed trains have been developed widely in European countries and Japan in order to transport large quantity of people and commodities in short time. Additionally, a high speed train is one of the most desirable and environmentally friendly transportation methods. When a high speed train enters a tunnel, aerodynamic resistance is generated suddenly. This resistance causes micro pressure wave and discomfort to passengers. Due to this aerodynamic pressure against the train, a large amount of traction is required for the operation of a train in a tunnel. Therefore, it is essential to incorporate a pressure relief system in a tunnel in order to reduce aerodynamic resistance caused by a high-speed train. A pressure relief duct and a vertical shaft are representative measures in a tunnel. This study represents the effect of pressure relief ducts in order to alleviate positive and negative normal pressures acting on a train. One-dimensional numerical simulations were carried out in order to estimate the effect of pressure relief systems.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.78-87
• /
• 2021

Understanding the liquid propellant transport phenomena in low gravity is essential for developing Korea Space Launch Vehicle (KSLV) upper-stage for the diversity of space missions. A low-gravity environment can be simulated via the free-fall method on the ground; however, the air drag is inevitable. To reduce air resistance during free fall, air-drag shield is usually adopted. In this study, the free-fall method was performed with an air-drag shield from a 7-m height tower. The acceleration of a falling object was measured and analyzed. Low gravity below 0.01 g was achieved during 1.2-s free fall with the air-drag shield. The minimum gravitational acceleration value at 1.2-s after free fall was ±0.005 g, which is comparable to the value obtained from Bremen drop tower experiments, ±0.002 g. A prolonged free-fall duration may enhance the low-gravity quality during the drop tower experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.984-985
• /
• 2004

The ISO 9053, acoustics - materials for acoustical applications - determination of airflow resistance was reviewed in order to make it as a KS and the basic contents were introduced. The measurement apparatus according to ISO 9053 were made and tested.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.132-138
• /
• 2003

The optimal design for a leading car considering the aerodynamic resistance is required on the high-speed train due to increasing of ratio of drag force with proportion for the square of velocity. The aerodynamic analysis using CFD in the stage of concept design offers more economical analysis method which is used to estimate the influence of flow and pressure around the leading car than the experimental method using the Mock-up. In this study, we want to assist the artistic design with aerodynamics analysis in order to get the optimal design for leading car with the operation speed of 180km/h. The results of aerodynamic analysis for two leading car models which one is expressed with lineal beauty and the other is with curvaceous beauty are compared with each other and they offer the proposal of modification for two models in order to decrease the drag force. The shape of curvaceous model is better for the pressure force but slightly worse for the viscous force than the other. The Fluent software is used for the calculation of flow profile in this study.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.38-42
• /
• 2004

The optimal design for a leading car considering the aerodynamic resistance is required on the high-speed train due to increasing of ratio of drag force with proportion for the square of velocity. The aerodynamic analysis using CFD in the stage of concept design offers more economical analysis method which is used to estimate the influence of flow and pressure around the leading car than the experimental method using the Mock-up. In this study, we want to assist the artistic design with aerodynamics analysis in order to get the optimal design for leading car made of composite material. The results of aerodynamic analysis for two leading car models, which one is expressed with lineal beauty and the other is with curvaceous beauty, are compared with each other and offer the proposal of modification for two models in order to decrease be drag force. The shape of curvaceous model is better for the pressure force but slightly worse for the viscous force than the other. The Fluent software is used for the calculation of flow profile in this study.

• 한국기계연구소 소보
• /
• s.12
• /
• pp.83-92
• /
• 1984