• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.4
• /
• pp.305-312
• /
• 1984

본 연구에서는 STS 316강의 고온 저사이클 피로강도와 파괴거동을 고찰하고자 고온 대기중에서 변형율 제어에 의한 인장.압축 저사이클 피로시험을 실시하였다. 전 변형율축, 탄성 변형율축 및 소성 변형율축과 피로수명과의 관계를 일정 변형율 속 도하에서 응력축, 온도 및 주파수의 영향과 파괴거동을 고찰하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.193-198
• /
• 2017

Alloy 617 is one of the primary candidate materials to be used in a very high temperature reactor (VHTR) system as an intermediate heat exchanger (IHX). To investigate the low cycle fatigue behavior of Alloy 617 weldments at a high temperature of $850^{\circ}C$, fully reversed strain-controlled fatigue tests were conducted with the total strain values ranging from 0.6~1.5％. The weldment specimens were machined using the weld pads fabricated with a single V-grove configuration by gas tungsten arc welding (GTAW) process. The fatigue life is reduced as the total strain range increases. For all testing conditions, the cyclic stress response behavior of the Alloy 617 weldments exhibited the initial cyclic strain hardening phenomenon during the initial small number of cycles. Furthermore, the overall fatigue cracking and the propagation or cracks showed a transgranular failure mode.

• Journal of Welding and Joining
• /
• v.14 no.1
• /
• pp.38-46
• /
• 1996

High temperature low cycle fatigue crack growth behavior is investigated over a range of two temperatures and various frequencies in SUS 304 stainless steel. It is found that low frequency and temperature can enhance time-dependent crack growth. With high temperature, low frequency and long crack length, ${\Delta}J_c/{\Delta}J_ f$, the ratio of creep J integral range to fatigue J integral range is increased and time-dependent crack growth is accelerated. Interaction between ${\Delta}J_f$ and ${\Delta}J_c$ is occured at high frequency and low temparature and ${\Delta}J_c$, creep J integral range is fracture mechanical parameter on transition from cycle-dependent to time dependent crack growth in creep temperature region.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.2
• /
• pp.98-111
• /
• 1995

High temperature low cycle fatigue shows that cycle-dependent crack growth owing to cyclic plastic deformation occurred simultaneosly with time-dependent crack growth owing to intergranular deformation. Consequently, to estimate crack growth rate uniquely, many to investigators have proposed various kinds of parameters and theories but these could not produce satisfactory results. Therefore the goal of this study is focused on prediction of crack growth rate using predominant damage rule, linear cumulative damage rule and transitional parameter ${\Delta}J_c/{\Delta}J_f$. On the basis of these sinusoidal loading waveform at 600$^{\circ}C$ and 700$^{\circ}C$.

• Journal of Welding and Joining
• /
• v.13 no.4
• /
• pp.7-13
• /
• 1995

마이크로솔더링에 의한 전자기기는, 사회기능의 중추가 되는 컴퓨터, 통신 기기, 항공기 인공위성 등의 제어계를 구성하므로, 그 접속부에 대한 높은 신뢰성의 요구는 그 무엇보다 중요하다. 전자기기에 있어서의 솔더 접속부는 집과 기판의 전기 적.기계적 접속의 역할을 하고 있으며, 따라서 개개의 접속부의 파단은 전체의 불량 으로 연결된다. 실제 전자콤포넌트와 그 시스템의 단선 등의 사고에 있어서 자주 발생 하는 사고중의 하나가 솔더접속부의 단선에 의한 것이며, 그 단선중에서도 가장 보편 적이며 또한 대단히 심각한 문제로서 주목을 받고 있는 것이 솔더접속부의 열피로파단 이다. 전자기기를 사용할 때, 스위치의 on-off에 의한 power cycle과 환경의 온도변화 에 기인하는 반복열 사이클은 솔더접속부의 피로를 일으키게 되고, 결국에는 사용중에 파단을 초래하게 된다. 이러한 온도변화의 범위는 약 -55.deg. - 150.deg.C로 예상할 수 있으며, 여기서 최고온도인 150.deg.C는 Pb-Sn 공정합금의 경우 0.9Tm.p.이상의 고온에 해당한다. 이 피로는 등온적으로 또는 열사이클중에 발생하기도 한다. 솔더접 속부의 열피로수명은 대부분의 공업재료에서 나타나는 저사이클피로거동과 유사하게 발생하며, 솔더 접속부에 인가되는 열변형/응력(thermal strain/stress)의 크기에 크게 의존하는 것으로 알려져 있다. 솔더는 서로 다른 열팽창계수를 갖는 칩과 회로 기관의 두종류의 재료를 접속하기 때문에, 상기한 바와 같은 반복열사이클에 의하여 발생하는 열변형/응력이 접속부의 피로.파단을 야기시킨다. 이러한 솔더접속부에 대한 주기적인 응력/변형의 인가는 접속부에 내.외적으로 현저한 변화를 야기시키게 되고, 열피로로 연결되며 결국에는 시스템의 전기적 단선을 초래하게 된다. 또한 열피로파단 현상는 변형/응력의 크기 뿐 만아니라 솔더합금자체의 야금학적인 물성에도 크게 의존 하며, 내적.외적인 열변화에 의한 야금학적인 특성변화도 크게 영향을 미친다. 솔더 접속부의 신뢰성에 대한 연구는, 그 중요성에 비추어 볼 때, 지금까지 수많은 연구가 행하여져 왔다. 그러나 신뢰성과 관련된 열피로파단현상에 대한 야금학적인 면에서의 연구는 비교적 적은 편이다. 따라서 본 해설에서는 전자기기의 마이크로 솔더접속부 에서 발생하는 열피로파단현상에 대한 야금학적인 면에 중점을 두어 서술하고자 한다.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.90-97
• /
• 2010

A study about the fatigue life of copper alloy which is used in inner jacket of regenerative cooling chamber of liquid rocket engine has been performed. Mechanical properties of the material and fatigue life have been taken from tensile tests and low-cycle fatigue tests at room temperature and several elevated temperatures. Original universal slopes method, modified universal slopes method, Mitchell's method, Baumel and Seeger's method, and Ong's method have been used for predicting the fatigue data. It was found that the novel life prediction method should be developed for the copper alloys since almost all data have not been predicted well with the widely used methods.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.539-547
• /
• 1985

The low-cycle fatigue crack growth behavior of SUS 304 Stainless steel was investigated at 650.deg. C by the nonlinear fracture mechanics. Crack Propagation can be separated in to cycle-dependent and time-dependent, the former is correlated with .DELTA. $J_{f}$ , J-intergral range and the latter is correlated with J', modified J integral. Transition from cycle-dependent to time-dependent crack growth was successfully predicted using the .betha. hypothesis, which was proposed by the authors on the basis of an analysis on the interaction of elastic and creep strain. To investigate the reliability of .betha.-hypothesis, experimenting by the change of stress-level, stress rate and frequency, following conclusions were obtained. (1) High temperature fatigue crack propagation was separated into cycle-dependent and time-dependent. (2) Transition of crack propagation was predicted by .DELTA. $J_{c}$/.DELTA.$_{f}$ or .betha. (3) Lower limit in cycle-dependent crack propagation was obtained..

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.41-48
• /
• 1999

The fatigue life tests were performed in strain control with triangular and hole-time wave-forms at $650^{\circ}C$. The fatigue lifes were investigated according to waveform examining damage mechanisms, which could be used to predict the fatigue life and estimate the remaining life. The results obtained are as follows; The fatigue lifes were in order of the fast-fast>the fast-slow>the slow-fast in the triangular waveforms, and the fatigue lifes in slow-fast waveforms got shorter in the hold-time waveforms. The damage mechanisms of the fracture surfaces were transgranular fracture in the fast-fast, the fast-slow waveforms and intergranular fracture in the slow-fast waveform.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.2
• /
• pp.140-149
• /
• 1985

Fully reversed push-pull low cycle fatigue tests under strain control of trapezoid cyclic mode have been conducted in air at temperature of 550.deg. C and with frequency of 0.5 cpm on the domestic stainless steel STS 316 after solution treatment for 1 hour at 1100.deg. C. As an experimental equipment for high temperature fatigue tests, an electric servo-hydraulic fatigue machine(Instron model 1350) was used. This paper presents the effects of creep hold time and plastic strain range on push-pull high temperature low cycle fatigue life and fracture behavior. The fracture surfaces were observed by means of the scanning electron microscope. The results are as follows. (1) The fatigue life decreases with increase of the plastic strain range equal hold time and also decreases as the hold time is getting longer. (2) The frequency modified damage function can predict fatigue life by incorporating a variation of Coffin's frequency modified approach into damage function. (3) The ratios of creep damage and fatigue damage can be calculated by using he linear accumulation damage concept and the ratio of creep damage increases as the hold time is getting longer. (4) At the creep hold time of 5 minutes and the strain range of 2.0%, the fracture mode was intergranular fracture and striations were hardly observed. In this case, the intergranular cracking was originated in void type('.gamma.' type) cracking.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.4
• /
• pp.2752-2759
• /
• 1996

This paper presents crack growth analysis approach on the basis of neural networks, a branch of cognitive science to high temperature low cycle fatigue that shows strong nonlinearity in material behavior. As the number of data patterns on crack growth increase, pattern classification occurs well and two point representation scheme with gradient of crack growth curve simulates crack growth rate better than one point representation scheme. Optimal number of learning data exists and excessive number of learning data increases estimated mean error with remarkable learning time J-da/dt relation predicted by neural networks shows that test condition with unlearned data is simulated well within estimated mean error(5%).