• Resources Recycling
• /
• v.9 no.3
• /
• pp.13-21
• /
• 2000

This study describes to analyze the heat transfer characteristics of waste solvent recovery system using a double pipe heat exchanger heating solvent by the hot oil. The solvent recovery system consists of the feeding pump, the double pipe heat exchanger, the vacuum spray chamber, and the condenser. A double pipe heat exchanger consists of the first section to conduct the heating of solvent to the thermal saturated point and the second section to evaporate the saturated solvent. The heat transfer area for vaporization of water, benzene and alkylbenzene was predicted by the heat balance modelling and experimentally measured from the temperature distribution as a function of solvent flow rate and heating temperature. The required heat transfer area for vaporization was increased with increasing solvent flow rates and with decreasing heating temperatures due to decreased quantity of transferred heat per the unit area. Theoretical modelling of the heat transfer area for solvents vaporization in the pipe showed good agreement with experimental results. Results showed to be suitable for the waste solvent recovery using a double pipe heat exchanger.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.299-305
• /
• 2000

In order to increase the thermal stability at high temperatures, new hybrid ceramic percursors were synthesized by chemical modification of polycarbosilane (PCS). The structure of hybrid ceramic percursors were investigated by using FT-IR and $^1$H-NMR spectrometers. The syntheses of hybrid ceramic precursors were confirmed by monitoring the change of the adsorption peaks appearing at 0893, 1092, 609 $cm^{-1}$ / on the FT-IR spectra, and also by the presence of peaks at 3.8, 2.0, 0.6 ppm on the $^1$H-NMR spectra. The conversion of hybrid ceramic percursor was around 74 and 10 wt% higher than that of the pure PCS. After the heat-treatment at 150$0^{\circ}C$, the crystalline peaks for $\beta$-SiC were observed at 2$\theta$=35.7, 42.2, 61.0$^{\circ}$ on the X-ray powder diffractogram. It showed the conversion of hybrid ceramic percursor to crystalline $\beta$-SiC.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.20 no.3
• /
• pp.90-103
• /
• 2017

This study analyzed the surface temperature characteristics of urban green spaces under high summer temperatures to clarify the functions of green spaces in reducing urban temperatures. We obtained accurate surface temperature data using highresolution unmanned aerial vehicle images of the survey site, which was an isolated green space in the city. We analyzed differences in the surface temperature by land cover type, vegetation type, species type, and the relationship between surface temperature and vegetation volume. Based on the results, among the land cover types, wetlands and forests had low temperatures and paving areas had very high temperatures. Regarding vegetation type, broad-leaved trees had lower temperatures than coniferous trees in forests. However, in planted areas, coniferous trees had lower temperatures than broad-leaved trees. The temperature of long grass was higher than that of short grass, which suggested that the volume of grass affected the temperature. Regarding forest species type, the temperature of broad-leaved Robinia pseudoacacia forest and mixed broad-leaved forest was lower than coniferous Pinus densiflora forest. There was a slight difference in temperature between R. pseudoacacia forest and mixed broad-leaved forest. The analysis of the relationship between vegetation volume and temperature by forest species type indicated a negative correlation, where the temperature decreased with increasing vegetation volume, similar to the results of previous studies. However, we found a weak positive correlation in R. pseudoacacia forest; therefore, an increase in volume may not reduce the surface temperature depending on the dominant species.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.184-190
• /
• 2000

We investigated the effect of filler content on the thermo-mechanical properties of modified ACA composite materials by incorporation of non-conducting fillers and the reliability of flip chip assembly on organic substrates using modified ACA composite materials. For the characterization of modified ACA s composites with different content of non-conducting fillers, differential scanning calorimeter (DSC), and thermo-gravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), and thermo-mechnical analyzer (TMA) were utilized. As the non-conducting filler content increased, CTE values decreased and storage modulus at room temperature increased. In addition, the increase in the content of filler brought about the increase of Tg^{DSC}$ and $Tg^{TMA}$. However, the TGA behaviors stayed almost the same. Contact resistance changes were measured during reliability tests such as thermal cycling, high humidity and temperature, and high temperature at dry condition. It was observed that reliability results were significantly affected by CTEs of ACA materials especially at the thermal cycling test. Results showed that flip chip assembly using modified ACA composites with lower CTEs and higher modulus by loading non-conducting fillers exhibited better contact resistance behavior than conventional ACAs without non-conducting fillers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3286-3291
• /
• 2014

A study on the crack protection and thermal insulation properties of the expanded perlite inorganic composites was performed. Mixed expanded perlite with a water glass was stabilized for 24 hrs at room temperature in the mold and, thereafter, converted into a massive foamed body through complete drying process at $150^{\circ}C$. Aluminum phosphate and micron size mica powder were used as a reaction accelerator and a stabilizer for thermal crack, respectively. Especially, use of mica exhibited a remarkable effect on the protection of thermal crack at higher temperature over $500^{\circ}C$, and thermal conductivity of the composites was enhanced with higher perlite contents, showing ca. 0.09 W/mK for the sample of 100/200/10/1.5 water glass/perlite/mica/Al phosphate by weight. A severe dimensional deformation of the composite materials was observed over $600^{\circ}C$, however, showing a temperature limitation for a practical application. The facts were considered as the results from the glass transition temperature of the water glass, of which main component is sodium silicate.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.487-495
• /
• 2017

The thermal characteristics of the electrodeless lamp are one of the main factors that determine the design and performance of the lamp. The coupler changes the impedance characteristic by heat and its use temperature is usually within about $150^{\circ}C$. In this study, we observed the phenomenon when the coupler was exposed at a temperature of $150^{\circ}C$ or higher, which has not been discussed so far. Two types of coupler A and coupler B with different spacing between the inner tube and the coupler were analyzed for electrical, thermal and optical properties and deterioration characteristics with different heat and heat shielding conditions. First, the impedance of the system is obtained and used as a criterion for analyzing the electrical characteristics through it. The diameters of the two types of couplers are 1 mm, and the experimental result shows that the coupler diameter is 1 mm, which can cancel out the loss of the magnetic field strength. Therefore, based on these results, when the coupler is exposed to high temperature of about $200^{\circ}C$, the efficient design method corresponding thereto is proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.670-675
• /
• 2016

Both melting temperature and enthalpy of MBCA/DMTDA mixtures were measured as a function of DMTDA compositions using DSC. The thermal properties of polyurethane elastomer samples prepared with MBCA, DMTDA, and 40/60 MBCA/DMTDA mixture as curing agents were also observed using TGA. MBCA and DMTDA showed good miscibility over the entire composition range, exhibiting individual DSC melting peaks. Peak temperatures were non-linearly reduced as DMTDA concentrations increased, being approximately $60^{\circ}C$ in the case of the 40/60 MBCA/DMTDA mixture. Furthermore, melting enthalpy of the mixture was calculated as 3.8 J/g, which was only 4.3% compared to 87.3 J/g of MBCA. Based on these results, crystallization of the mixture was considered to occur very slowly, and the fluidic gel-state of the mixture was visually confirmed to be maintained over 5 days at room temperature. Thermal decomposition of polyurethane elastomer prepared with 40/60 MBCA/DMTDA curative started at about $190^{\circ}C$, which is similar to that observed for DMTDA, only except decomposition behavior over higher temperature of $400^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.474-481
• /
• 2018

The policy-making and technological development of eco-friendly automobiles designed to increase their supply is ongoing, but the internal combustion engine still accounts for approximately 95% of automobiles in use. To meet the stricter emission regulations of internal combustion engines based on fossil fuels, the proportion of after-treatments for vehicles and (ocean going) vessels is increasing continuously. As diesel engines have high power and good fuel economy in addition to less CO2 emissions, their market share is increasing not only in commercial vehicles, but also in passenger cars. Because of the characteristics of the diesel combustion, however, NOx is generated in localized high-temperature combustion regions, and particulates are formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for the after-treatment of exhaust gas to reduce NOx in diesel vehicles. This study examined the effect of a containing promoter on SCR catalysts to cope with the severe exhaust gas regulation. The de-NOx performance of the Mn-SCR catalyst was the best, and the de-NOx performance was improved as the ion exchange rate between Mn ion and Zeolyst was good and the activation energy was low. The de-NOx performance of the 7Cu-15Ba/78Zeoyst catalyst was 32% at $200^{\circ}C$ and 30% at $500^{\circ}C$, and showed the highest performance. The NOx storage material of BaO loaded as a promoter was well dispersed in the Cu-SCR catalyst and the additional de-NOx performance of BaO was affected by the reduction reaction of the Cu-SCR catalyst. Among the three catalysts, the 7Cu-15Ba/Zeolyst SCR catalyst was resistant to thermal degradation. The same type of CuO due to thermal degradation migrates and agglomerates because BaO reduces the agglomeration of the main catalyst CuO particles.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.121-121
• /
• 2012

산업이 고도화, 다원화, 세계화되고 있는 현대사회는 다기능성, 고물성, 극한 내구성을 가지며 환경 친화적이면서 에너지 효율을 극대화시킬 수 있는 다기능 소재의 개발을 요구하고 있다. 이러한 시점에서 다양한 물성을 동시에 발현이 가능한 코팅 소재는 향후 미래에 중요한 원천 소재로서 주목되고 있다. 특히, 환경에 의해 쉽게 물성 및 구조의 변화가 쉬운 종래의 코팅소재와는 달리, 다양한 외부환경에서도 미세 구조 및 물성을 안정적으로 유지할 수 있는 신개념의 코팅 소재의 개발이 절실히 요구되고 있다. 이를 위해서는 코팅소재의 다 성분화가 필수적이다. 최근의 코팅 기술은 2가지 이상의 물성, 특히 서로 상반되는 물성을 동시에 구현할 수 있는 소재의 개발을 요구하고 있다. 이러한 물성의 구현을 위하여 더 많은 성분으로 구성되며 더욱 복잡한 조직으로 구성된 코팅층에 대한 개발이 진행이 필요하다. 본 연구에서 목표로 하는 신 개념의 원천소재기술은 4성분계 이상의 원료 물질을 단일 타겟으로 제조하여, 단순한 공정으로서 단일 코팅층 내에 다양한 성분과 10 nm 미만 크기의 나노 결정립/나노 비정질로 구성된 나노 복합 구조의 형성이 가능하도록 하는 기술을 개발하고자 한다. 이를 통해 복합기능 3 이상의 다기능성 부여는 물론, 그림 1에 정리된 기존 코팅재에서 결여된 특성을 포함한 극한 기능성(광대역 윤활성, 전자 이동 제어에 의한 온도 저항 계수 및 전기 저항 조절, 고온 열적 안정성, 내산화성, 고열전도율, 초저마찰/내구성/초고경도성 등)의 구현이 가능한 복잡한 형태의 나노 복합 코팅층 소재 개발이 가능하도록 하는 기술이다. 또한 기존 코팅재의 구조적 결함을 통해 발생하는 내식성 문제를 방지할 수 있는 기술이다. 다성분계 모물질의 개발이 중요한 이유는 다수의 성분 원소를 합금 상태로 형성시킴으로서, 단일 소스에 의해 다양한 원소를 동시에 스퍼터링 및 증착이 가능하도록 할 수 있다는 장점을 가지기 때문이다. 특히, 타겟의 미세구조를 나노구조화 하는것을 통해, 스퍼터링 yield의 차이가 큰 원소일지라도 균일하게 증착시킬 수 있는 방법을 개발하고자한다. 또한 다수의 타겟을 이용하여 균일한 다성분 코팅층 형성하는 기존의 PVD 코팅방법으로는 다수의 성분타겟을 사용함으로서 장비의 복잡성, 코팅의 재현성, 대형화 등의 문제점을 본질적으로 갖고 있다. 이를 위한 해결방법으로 본 발표에서는 3가지 이상의 다기능성 구현을 위한 가장 중요한 원천기술이라 할 수 있는 다성분계 타겟 모물질 제조 기술의 개발 진행 사항에 대해 소개하고자 한다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.1
• /
• pp.95-105
• /
• 2014

Reinforced concrete (RC) shield tunnel lining must be designed for fireproof performance because the lining is sometimes exposed to very high temperature due to traffic accidents. Both experimental and numerical studies are carried out to evaluate fire resistance performance of precast RC tunnel lining systems. In the experimental studies, six full-scale precast RC tunnel segments are exposed to fire in order to examine the influence of various parameters on the fire resistance performance of precast RC tunnel lining. We used the temperature curve of the RABT criteria, which are severe conditions of fire temperatures. The fire test showed that the explosive spalling was not observed by substituting concrete to PP fiber reinforced concrete. A transient heat flow analysis was carried out in consideration of the material properties that change with temperature, and the results showed good agreement with the test results.