• Journal of the Korean Geotechnical Society
• /
• v.37 no.10
• /
• pp.13-25
• /
• 2021

The most widely used method for determining the blast effects of explosives is the Trauzl test. This test is used to measure the explosive power (strength) of a substance by determining volume increase, which is produced by the detonation of a tested explosive charge in the cavity of a lead block with defined quality and size. In this paper, Trauzl lead block test and High speed 3D-DIC (Digital Image Correlation) system were conducted to evaluate the stemming effect of the blast hole. The effects of stemming materials can be expressed as the expansion of the cavity in a standard lead block through explosion of the explosives. The blasting experiment was conducted with emulsion explosives. The stemming material in the blast hole of lead block, which was adopted in this study, were using sand and stone chips. Results of blasting experiment and numerical analysis showed that the expansion rates of lead block were most affected by stone chips followed by sand. Also, as result of dynamic strain measurement on the lead block surface of High speed 3D-DIC system, the displacement and surface strain on the block were the highest in the experiment case of stone chips stemming.

• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.572-579
• /
• 2009

This study is to investigate experimentally the flame structure and propagation mechanism in dust explosions and to provide the fundamental knowledge. Upward propagating laminar dust flames in a vertical duct of 1.8 m height and 0.15 m square cross-section are observed and flame front is visualized using by a high-speed video camera. Also, the thicknesses of preheated and reaction zone have been determined by a schlieren, electrostatic probe and thermocouple. The thickness of preheated zone in lycopodium dust flame is observed to be 4~13 mm, about several orders of magnitude higher than that of premixed gaseous flames. From the experimental results by a PIV(Particle Image Velocimetry) system, a certain residence time of the unburned particle in preheated zone is needed to generate combustible gas from the particle. The residence time will depend on preheated zone thickness, particle velocity and flame propagation velocity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.11
• /
• pp.2365-2373
• /
• 2011

This paper propose the hardware IP of real-time face detection system for mobile devices and digital cameras required for high speed, smaller size and lower power. The proposed face detection system is robust against illumination changes, face size, and various face angles as the main cause of the face detection performance. Input image is transformed to LBP(Local Binary Pattern) image to obtain face characteristics robust against illumination changes, and detected the face using face feature data that was adopted to learn and generate in the various face angles using the Adaboost algorithm. The proposed face detection system can be detected maximum 36 faces at the input image size of QVGA($320{\times}240$), and designed by Verilog-HDL. Also, it was verified hardware implementation by using Virtex5 XC5VLX330 FPGA board and HD CMOS image sensor(CIS) for FPGA verification.

• Journal of Korea Society of Industrial Information Systems
• /
• v.12 no.1
• /
• pp.95-100
• /
• 2007

In the steel & iron processing line, some characters are marked for the material management in the surface of material. This paper describes about the developed results of vision system for the recognition of material management characters, which was included in the slab image. Our vision system for the character recognition includes that CCD camera system which acquire slab image, optical transmission system which transmit captured image to the long distance, input and output system for the interface with existing system and monitoring system for the checking of recognition results. We have installed our vision system at the continuous casting line and tested. Also, we have performed inspection of durability, reliability and recognition rate. Through the testing, we have confirmed that our system have high recognition rate, 97.4%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.61-69
• /
• 2015

The objective of this study is to experimentally investigate the mixed flow behaviors and oxygen transfer characteristics of a vertical orifice ejector. The experimental apparatus consisted of an electric motor-pump, an orifice ejector, a circulation water tank, an air compressor, a high speed camera unit and control or measurement accessories. The mass ratio was calculated using the measured primary flow rate and suction air flow rate with experimental parameters. The visualization images of vertically injected mixed jet issuing from the orifice ejector were qualitatively analyzed. The volumetric oxygen transfer coefficient was calculated using the measured dissolved oxygen concentration. At a constant primary flow rate, the mass ratio and oxygen transfer coefficient increase with the air pressure of compressor. At a constant air pressure of the compressor, the mass ratio decreases and the oxygen transfer coefficient increases as the primary flow rate increases. The residence time and dispersion of fine air bubbles and the penetration of mixed flow were found to be important parameters for the oxygen transfer rate owing to the contact area and time of two phases.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.205-209
• /
• 2017

Unlike spherical drop impact, ellipsoidal drop impact can control the bouncing height on a heated surface by significantly altering impact behavior. To scrutinize the effect of the aspect ratio (AR) of the drop on the bounce suppression, in this study, non-axisymmetric spreading behaviors are observed from two side views and characterized based on the spreading width of the drop for horizontal principal axes. In addition, the maximum spreading width is investigated for various ARs. The results show that as the AR increases, the maximum spreading width of the minor axis increases, whereas that of the major axis shows no significant variation. In the regime of high AR and high impact velocity, liquid fragmentations by three parts are observed during bouncing. These fragmentations are discussed in this work. The hydrodynamic features of ellipsoidal drop impact will help understand bouncing control on non-wetting surfaces for several applications, such as self-cleaning and spray cooling.

• Fire Science and Engineering
• /
• v.19 no.2 s.58
• /
• pp.63-68
• /
• 2005

In this study, the arc dispersion properties were analyzed according to switching of high sensitive type Residual Current Protective Device(RCD) contacts. Arc dispersion and ignition process was taken by high speed imaging system(HSIS). In this experiment, electric lamps(60 W) and heaters(950 W) were connected in parallel as loads. In case of normal RCD, it took about 2.3(ms) from the generation of arc to the extinction of uc. When arc was dispersed in normal RCD, it did not ignite cotton. Whereas, in case of RCD deteriorated by NaCl solution, the range of arc dispersion was wider and the arc lasted for 3.3[ms] more compared to normal RCD. And the arc ignited cotton. In order to prevent accidents caused by RCD, we should be careful of environmental factors, such as dust and humidity, and the parts of RCD should be used as incombustible materials.

• Journal of the Korean Institute of Gas
• /
• v.15 no.5
• /
• pp.13-18
• /
• 2011

Experimental studies were carried out to investigate the characteristics of explosion mitigations by varying concentrations of agar gel barriers in an explosion chamber, 1400 mm in length, with a square cross-section of $100{\times}100mm^2$. Another extension chamber, $100{\times}100{\times}300mm^3$, was made to hold a gel barrier. Four different gel concentrations were used in the measurements: 2, 3, 4, 5 %(by weight of gel). Displacement of the gel barrier was measured using a high speed camera, and pressure development was measured using pressure transducers and a data acquisition system. It was found that as the concentrations of the gel barriers increased, the gel rupture time and the time taken to reach the maximum pressure increased. It was also found that the increment of gel concentrations increased the reduction percentage in the maximum pressure between before and after gel barrier.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.161-168
• /
• 2015

An experimental study was conducted to scrutinize the influence of the frequency of an ultrasonic standing wave on the variation in the behavior of a methane-air premixed flame. The evolutionary features of the propagating flame were captured by a high-speed camera, and the macroscopic flame behavior, including the flame structure and local velocities, was investigated in detail using a post-processing analysis of the high-speed images. It was found that a structural variation and propagation-velocity augmentation of the methane-air premixed flame were caused by the intervention of the ultrasonic standing wave, which enhanced the combustion reaction. Conclusive evidence for the dependency of the flame behaviors on the driving frequency of the ultrasonic standing wave and equivalence ratio of the reactants is presented.