• 어항어장
• /
• s.18
• /
• pp.69-77
• /
• 1992

고강도 콘크리트의 실용화 일환으로 설계기준강도 500kg/cm$^2$ 이상인 고강도 콘크리트의 현장 B/P 생산과 실대구조물의 시공성 및 강도, 온도 특성에 관한 연구를 수행하였다. 이러한 연구를 위해 현장 최적배합비 선정과 레미콘 운반시간에 따른 경시변화 시험을 수행하였고 실대구조물의 코아강도 및 콘크리트 내부온도를 측정하였다. 일반 현장재료와 장비의 사용으로도 고강도 콘크리트의 생산과 시공성을 확보할 수 있었으며 실대구조물의 코아강도가 500kg/cm$^2$ 이상을 나타냄으로써 고강도 콘크리트의 실용화에 대한 가능성을 확인할 수 있었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.2
• /
• pp.133-140
• /
• 2011

High strength concrete used for large structures is vulnerable to fire due to explosive spalling when it is heated. Recently, various research is conducted to enhance the fire-resistance of the high strength concrete by reducing the explosive spalling at the elevated temperature. In this study, a heat transfer analysis model is proposed for a fiber-embedded fire-resistant high strength concrete. The material model of the fire-resistant high strength concrete is selected from the calibrated material model of a high strength concrete incorporating thermal properties of fibers and physical behavior of internal concrete at the elevated temperature. By comparing the simulated results using the calibrated model with the experimental results, the heat transfer model of the fiber-embedded fire-resistant high strength concrete is proposed.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.2 s.20
• /
• pp.53-60
• /
• 2006

The shear failure modes of reinforced concrete members using high-strength materials (high-strength concrete and high-strength steel) are different to those of reinforced concrete members using normal-strength materials. The reinforced concrete members using high-strength materials are inclined to fail due to concrete crushing before the shear reinforcing bar reaches its yield strength. This paper presents an evaluation equation to calculate the maximum shear reinforcement ratio based on the material stresses and strains when the reinforced concrete members fail in shear. The maximum shear reinforcement ratio calculated by the proposed equation increases as the compressive strength of concrete increases. Test results of 97 reinforced concrete members reported in the technical literatures are used to check the validity of the proposed equation. The comparison between the test results and the ratio calculated using the proposed equation indicated that the shear failure modes depended on the interaction between the amount of shear reinforcement and the compressive strength of concrete.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.379-382
• /
• 2009

횡방향으로 구속된 콘크리트의 응력-변형률 거동은 구속되지 않은 콘크리트와는 다른 거동을 한다. 보통강도 콘크리트에서 구속효과를 고려한 콘크리트 재료모델로는 Mander 모델이 대표적이며 고강도 콘크리트의 구속효과의 경우 여러 연구자들에 의하여 제안된 모델 중 공시체 수준의 실험결과와 잘 일치하는 Sakino-Sun 모델을 사용하였다. 보통강도에서는 Mander모델을 고강도 콘크리트에서는 Sakino-Sun 모델을 사용하였으나 중간 강도인 30-40MPa의 강도에서 Mander 모델과 Sakino-Sun 모델의 적용시 실험결과와 해석결과가 다소 차이를 보이며 또한 두 모델은 적용할 수 있는 최대 또는 최소 콘크리트 압축강도의 한계범위가 명확하지 않다. 따라서 이 연구에서는 30-40MPa의 강도의 횡방향으로 구속된 콘크리트의 비선형 재료모델을 제안하고 실제 30-40MPa의 압축강도를 갖는 콘크리트 공시체의 일축압축시험 결과와의 비교를 통해 그 적용성을 검토하였다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.29-34
• /
• 1989

고분자 복합재료들은 오늘날 광범위하게 마찰 부위들에 응용되고 있다. 다양한 첨가제와 보강재들이 고분자 물질들에 넣어져 강도와 마모 특성들을 향상 시키고 있다. 예를 들어, 다양한 복합재료들로서 현재 입수 가능한 것에 베어링 재료들이 있으며 이에 포함되는 것이 자체 윤활 보강 플라스틱 들이며 이들에는 고체 윤활제, 즉, 테플톤, $MoS_2$, 혹은 흑연가루들이 첨가된다. 실험적 그리고 이론적인 연구들이 여러 조건들에서의 섬유 보강 복합 재료들의 마모 거동에 대하여 보고되었다(예를 들어, 미끄럼 마모, 연마 마모, 입자 충격 마모, 비빔 마모). Tsukizoe와 Ohmae의 보고에 의하면 탄성계수 탄소섬유 복합재료는 가장 적은 마모가 횡단 방향(Transverse)에서 있고, 고 강도 탄소 섬유 복합재료는 길이 방향(Longitudinal)에서 있다. 가장 많은 마모는, 고 탄성계수 복합재료는 길이 방향에서, 고 강도 섬유 복합재료는 횡단 방향에서 잇다. 그들이 또한 발표한 것은 양쪽의 고 탄성계수와 고 강도 섬유 복합재료들의 수직방향(Norma)에서 눌러 불음(Seizure)가 일어났다고 한다.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.559-568
• /
• 2006

The purpose of this study is to evaluate the mechanical performance and fire resistance of wet-mixed high strength sprayed polymer-modified mortar in order to protect tunnel lining system which are in the event of fire disaster. Since the current commercial fire-resistant materials reproduce the low strength issue of mortar, this study aims to provide an enhanced fire-resistant mortar with a proper strength. Normally, a large temperature gradient phenomenon arise in the vicinity of free surfaces which are fully exposed in the event of persistent flame. Thereby, the determination of optimal cover depth of wet-mixed high strength sprayed polymer-mortar(WHSPM) is important for fire-resistance of tunnel lining system. With comparison of current commercial fire-resistance materials and WHSPM, the experimental result of WHSPM shows the better fire-resistant performance than the others. In addition, the cover limitation should be controlled by minimum 4cm depth in order to avoid fire-induced damage.

• Land and Housing Review
• /
• v.3 no.3
• /
• pp.287-297
• /
• 2012

To develop 80MPa-high strength concrete with ternary cement used in OPC, blast-furnance slag, and fly ash, mixing ratio of blast-furnace slag and fly ash was evaluated in material characteristics before and after hardening of the high strength concrete. According to the evaluated results of material characteristics before and after hardening of the high strength concrete, the flowability and long-term compressive strength increase up to 30% mixing ratio of blast-furnace slag and fly ash. Also, it is superior to characteristics of length change and neutralization due to the use of mineral admixture when compared in test sample mixed with OPC. The evaluated results show that material characteristics of the high strength concrete was the most outstanding performance at blast-furnace slag of 25% and fly ash of 15%. The result of this study will be useful for the development of high strength concrete as a substitute of costly silica fume in the near future.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.2
• /
• pp.83-92
• /
• 1992

본 연구의 목적은 현장에서 구입 가능한 저품질의 재료를 사용한 일련의 실험을 통하여 28일 압축강도와 물\ulcorner시멘트비와 관계를 유출함으로써 고강도 콘크리트의 배합설계식을 얻기 위한 것이다. 목표슬럼프는 고층건물에서의 시공성을 고려하여 15$\pm$2cm로 하였으며 혼화제로는 고성능감수제를 사용하였다. 실험결과로부터 고강도콘크리트의 응력-변형도 특성을 비롯하여 탄성계수, 포아송비, 단위중량 등 고강도 콘크리트의 일반적인 재료성질을 얻었으며 본 연구에서 제안한 고강도콘크리트의 배합설계식은 국내현장조건을 고려한 실용식으로 고강도콘크리트으 설계 및 시공을 위한 기초자료로 사용 가능하다고 판단된다.

• Composites Research
• /
• v.12 no.2
• /
• pp.91-100
• /
• 1999

The manufacture of high strength polyethylene(HSPE) tape yarns has been accomplished by a solid state processing(SSP) method as the compaction of ultra-high molecular weight polyethylene(UHMWPE) powders and drawing of the compacted film under the melting point without any organic solvents. In this study, the characteristics of HSPE tape yarns produced by SSP which is desirable for production cost and environmental aspect were analyzed. As the results, tensile strengths of HSPE tape yarns increased with increasing the draw ratio and the fracture morphology of highly drawn HSPE tape yarns showed more fibrillar shape than the low drawn one. Interfacial shear strengths of HSPE tape yarns with vinylester resin increased by $O_2$ plasma treatment and maximum interfacial shear strength was obtained in the plasma treatment condition of 100W and 5min. In addition, mechanical properties of HSPE tape yarn reinforced composites were investigated and compared with those of the gel spun HSPE fiber reinforced composites.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.69-75
• /
• 2017

Ultra-high performance concrete and high ductile cementless composite are considered as promising construction materials because those exhibits higher performance in terms of high strength and high ductility. The purpose of this study is to investigate experimentally the compressive strength and tensile behavior of ultra-high performance concrete and high ductile cementless composite. A series of experiments including density, compressive strength, and uniaxial tension tests were performed. Test results showed that the compressive strength and tensile strength of alkali-activated slag based high ductile cementless composite were lower than those of ultra-high performance concrete. However, the tensile strain capacity and toughness of alkali-activated slag based high ductile cementless composite were higher than those of ultra-high performance concrete. And it was exhibited that a high ductility up to 7.89% can be attainable by incorporating polyethylene fiber into the alkali-activated slag based cementless paste.