• Composites Research
• /
• v.21 no.4
• /
• pp.15-21
• /
• 2008

Interfacial shear strength between epoxy and carbon fiber was analyzed utilizing a hemi-spherical microbond specimens adhered onto single carbon fiber. The hemi-spherical microbond specimen showed high regression coefficient and small standard deviation in the measurement of interfacial strength as compared with a droplet and an inverse hemi-spherical one. This seemed to be caused by the reduced meniscus effects and the reduced stress concentration In the region contacting with a pin-hole loading device. Finite element analysis showed that the stress distributions along the fiber/matrix interface in the hemi-spherical specimen had a stable shear stress distribution along the interface without any stress mode change. The experimental data was also different according to the kinds of loading device such as the microvise-tip and the pin-holed plate.

• Journal of Adhesion and Interface
• /
• v.10 no.2
• /
• pp.90-97
• /
• 2009

Dispersion and self-sensing evaluation for single-carbon fiber reinforced in three different acid-treated CNT-epoxy nanocomposites were investigated by electro-micromechanical techniques and wettability tests. Self-sensing based on contact resistivity exhibited more noise for single carbon fiber/acid-treated CNT-epoxy composites than it did for untreated CNT. However, the apparent modulus was higher the acid treated case than the untreated case which is attributed to better stress transfer. The interfacial shear strength (IFSS) between carbon fibers and the CNT-epoxy was lower than that between carbon fiber and neat epoxy due to the increased viscosity associated with the addition of the CNT. The CNT-epoxy nanocomposite exhibited more hydrophobicity than did neat epoxy. Change in the thermodynamic work of adhesion was consistent with changes in the IFSS but disproportional to that of the apparent modulus. The optimum condition of acid treatment on the need can be obtained instead of the maximum condition.

• Journal of Adhesion and Interface
• /
• v.11 no.4
• /
• pp.149-154
• /
• 2010

Interfacial evaluation was investigated for single-carbon fiber/phenolic and carbon nanotube (CNT)-phenolic composites by micromechanical technique and electrical resistance measurement combined with wettability test. Compressive strength of pure phenol and CNT-phenolic composites were compared using Broutman specimen. The contact resistance of CNT-phenolic composites was obtained using a gradient specimen by two and four-point methods. Surface energies and wettability by dynamic contact angle measurement were measured using Wilhelmy plate technique. Since hydrophobic domains are formed as heterogeneous microstructure of CNT in the surface, the dynamic contact angle exhibited more than $90^{\circ}$. CNT-phenolic composites exhibited a higher apparent modulus than neat phenolic case due to better stress transferring effect. Work of adhesion, $W_a$ between single-carbon fiber and CNT-phenolic composites exhibited higher than neat phenolic resin due to the enhanced viscosity by CNT addition. It was consistent with micro-failure patterns in microdroplet test.

• Journal of the Korean Ceramic Society
• /
• v.13 no.3
• /
• pp.55-62
• /
• 1976

순수한 닉켈과 금 박막을 (III)규소 단 결정위에 진공 증착시켰다. Ni/Au/Si나 Au/Ni/Si시료를 진공중에서 약 55$0^{\circ}C$로 가열하였을 때 육방정 혹은 변형된 육방정의 미소 결정들이 규소 기질위에 형성되었다. 이들 미소 결정들의 형성과정 및 조성은 X-선 회절법, scanning electron microscopy 및 scanning Auger microprobe 법을 사용하여 결정하였다. 이들 미소 결정은 NiSi2임이 확인되었다. Ni/Au/Si 시료에서는 Au-Si 공융점(37$0^{\circ}C$) 이상으로 온도가 증가됨에 따라 닉켈과 규소가 Au-Si 공융체 속으로 이동한 후 반응하여 NiSi2를 형성하였다. Au/Ni/Si 시료에 있어서의 Au-Si 공융체 형성은 닉켈 박막에 있는 바늘구멍형의 표면 결함과 관련 지을 수 있겠다. 금이 닉켈 박막의 grain boundary를 통하여 Ni/Si 계면으로 확산되어 그 계면을 습윤시킨 다음 Au-Si 공융체를 형성하였다. 이런 Au-Si 공용체는 닉켈과 규소 원자에 대한 높은 확산 매질로서 작용하여 NiSi2 형성을 촉진시켰다. 표면에 평행한 (III)규소면 위의 NiSi2 미소 결정은 유사한 육방정으로 나타났으며, 경사진 미소결정은 부등변 사변형과 유사하였다. Auger 스펙트럼 및 Ni, Au 및 Si에 대한 내층조성(indepth Composition Profiles)은 NiSi2 미소 결정이 Au-Si 공융체의 matrix에 미소 부분으로 나타났음을 보여주었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.5
• /
• pp.411-422
• /
• 2010

Self-sensing on micro-failure, dispersion degree and relating properties, of carbon nanotube(CNT)/epoxy composites, were investigated using wettability, electro-micromechanical technique with acoustic emission(AE). Specimens were prepared from neat epoxy as well as composites with untreated and acid-treated CNT. Degree of dispersion was evaluated comparatively by measuring volumetric electrical resistivity and its standard deviation. Apparent modulus containing the stress transfer was higher for acid-treated CNT composite than for the untreated case. Applied cyclic loading responded well for a single carbon fiber/CNT-epoxy composite by the change in contact resistivity. The interfacial shear strength between a single carbon fiber and CNT-epoxy, determined in a fiber pullout test, was lower than that between a single carbon fiber and neat epoxy. Regarding on micro-damage sensing using electrical resistivity measurement with AE, the stepwise increment in electrical resistivity was observed for a single carbon fiber/CNT -epoxy composite. On the other hand, electrical resistivity increased infinitely right after the first carbon fiber breaks for a single carbon fiber/neat epoxy composite. The occurrence of AE events of added CNT composites was much higher than the neat epoxy case, due to micro failure at the interfaces by added CNTs.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.2
• /
• pp.1-11
• /
• 2008

Phenanthrene uptake by surfactant sorbed on activated carbon was investigated to recycle of surfactant in washed solution for contaminated soil. The partitioning of phenanthrene to the activated carbon coating with Triton X-100 as a surfactant was also evaluated by a mathematical model. Phenanthrene-contaminated soil (200 mg/kg) was washed in 10 g/L of surfactant solution. Washed phenanthrene in solution was separated by various particle loadings of granular activated carbon through a mode of selective adsorption. Removal of phenanthrene was 99.3%, and surfactant recovery was 88.9% by 2.5 g/L of granular activated carbon, respectively. Phenanthrene uptake by activated carbon was greater than that of phenanthrene calculated by a standard model for a system with one partitioning component. This is accounted for enhanced surface solubilization by hemi-micelles adsorbed onto granular activated carbon. The effectiveness factor is greater than 1 and molar ratio of solubilization to sorbed surfactant is higher than that of liquid surfactant. Results suggest that separation of contaminants and surfactants by activated carbon through washing process in soil is much effective than that of calculated in a theoretical model.

• Applied Chemistry for Engineering
• /
• v.23 no.5
• /
• pp.433-439
• /
• 2012

In this study, a cationic surfactant BHMAS (N,N-bis-(3'-n-dodecyloxy-2'-hydroxypropyl)-N-methyl-2-hydroxyethylammonium methyl sulfate) having two lauryl and three hydroxyl groups was synthesized by the reaction of n-dodecyl glycidyl ether and 2-aminoethanol followed by the quarternization with dimethyl sulfate. The structure of the product was elucidated by $^{1}H-NMR$ and FT-IR. The CMC (critical micelle concentration) and surface tension of BHMAS at CMC condition were found to be $9.12\;{\times}\;10^{-4}$ mol/L and 28.71 mN/m respectively. Dynamic surface tension measurements using a maximum bubble pressure tensiometer indicated that a relatively long time was required to saturate the interface between air and aqueous surfactant solution. The interfacial tension measured between 1 wt% surfactant solution and n-decane reached an equilibrium value of 0.045 mN/m in 5 min. The adsorption capacity of the synthesized surfactant was observed to be excellent, which suggests that the surfactant can be used as a softening agent during a laundry process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.275.1-275.1
• /
• 2016

반전형 폴리머 태양전지는 그 구조에 의하여 훌륭한 안정성을 가질 뿐만 아니라 roll-to-roll 공정을 통한 대량생산이 가능하여 각광받고 있는 구조이다. 이런 반전형 구조에서, 금속 산화물 나노파티클에 의해 만들어지는 금속 산화물 층은 전자수송층으로서 사용된다. 이 연구에서는 표면개질 물질인 PEIE (Polyethyleneimine-ethoxylate)와 화학적으로 기능화된 산화아연/그래핀 핵/껍질 양자점을 이용하여 전기수송층의 역할을 하는 기능화된 산화아연/그래핀 단분자층을 가지는 태양전지를 제작하였다. 이는 기능화된 산화아연/그래핀 단분자층이 표면개질, 광센서, 전기수송층의 역할을 동시에 수행하는 효과로 인해 제작된 태양전지는 향상된 전자 수집능력을 보였다. 단분자층이 잘 형성되어 있는지 확인하기 위하여 집속 이온 빔 장비를 이용하여 태양전지의 내부 구조를 확인하였으며, density functional theory (DFT)을 이용한 모델링을 통하여 기능화된 산화아연/그래핀 양자점의 전자상태밀도를 분석하였다. 기능화된 산화아연 단분자층에 의한 효과적인 계면 제어 및 전하수송에 의해 약 10.3%의 높은 효율을 가지는 반전형 폴리머 태양전지를 제작할 수 있었다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.221-227
• /
• 2001

Both strength and stiffness of RC structures strengthened by a steel plate greatly increase and however, their ductility might not be sufficient because premature failures usually occur at the adhesive-concrete interface. In this study, Mohr-Coulomb criterion was adopted to examine the bonding failure mechanism, and the diagonal shear bonding test, the direct shear bonding test, and the flexural test on RC beams strengthened by a steel plate were carried out to measure the bonding properties. It is found from the experimental and numerical results that the cohesive strengths of epoxy-concrete interfaces are ranging from 50 kgf/㎠ to 70 kgf/㎠ when the friction angle is 45°. Bonding failure loads can be predicted by applying the bonding properties to the structural analysis of RC beams strengthened by steel plate. By considering them in the design of strengthened beams, the premature failure would be effectively prevented.

• Journal of the Korean Chemical Society
• /
• v.37 no.4
• /
• pp.416-422
• /
• 1993

As a result of adsorbing phthalocyanine (metal free, ${\alpha}\;and\;{\beta}$-Cu) on zinc oxide in aqueous solution using nonionic surfactant, all of the added dye was adsorbed and Na salt of sulfonated phthalocyanine showed the Langmuir monolayer adsorption. To analyze the effect of adsorption on zinc oxide, photovoltage was measured using surface photovoltmeter. The high photovoltaic effect was observed at intrinsic wavelength of zinc oxide and wavelength of adsorbed phthalocyanine dye. Metal free phthalocyanine, ${\alpha}$-copper phthalocyanine and ${\beta}$-copper phthalocyanine showed the highest photovoltaic effect when the percentage of coverage (${\theta}_{BET}$) for zinc oxide is about 80, while sulfonated phthalocyanine showed the highest photovoltaic effect when the percentage of coverage for zinc oxide is about 30.