• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.397-406
• /
• 2003

Several sensor systems are used to estimate the reinforcing effect of stabilizing pile in slopes, and to find a failure surface in slopes effectively. FBG(Fiber Brags Crating) sensor, V/W(Vibrating Wire) sensor and inclinometer have shown a great potentiality to serve real time health monitoring of the reinforcing structures. Field tests and test results have shown great solutions for sensor systems of Smart Structures. The purpose of this research is to seek for the relationships among the slope movement and the reinforcing effect of stabilizing pile, and the strain distribution of stabilizing pile in a active zone by analyzing the data from the in-situ measurement so that the possible failure surface should be well defined based on the relationships. The field test results have shown that the data by FBG sensor are well coincided with those of V/W sensor and inclinometer, and the reinforcing effect of the stabilizing pile is good enough.

• The Journal of Engineering Geology
• /
• v.33 no.1
• /
• pp.137-149
• /
• 2023

In order to intuitively grasp the earth pressure direction acting on the structure and displacement state, displacement data in the horizontal and vertical directions were processed using the sigmoid function. A displacement coordinate system was set up for each axis. The system can intuitively check the current displacement and assess the management stage of each point. A displacement path can be compiled from continuously recorded points, allowing trends in the displacement's history and stress direction to be known. Analysis of data measured for excavated ground, found that displacement occurred in the direction of destressing at all points, and that the points' management state steady. Similar behavior trends were found among measurement points with high spatial correlation, whereas differing behavior trends occurred among measurement points with low spatial correlation. If the correlation analysis of the precursor and behavior area is performed using the continuously distributed surface settlement data and displacement coordinate system, it will be possible to predict the failure time and area.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.4
• /
• pp.129-137
• /
• 2007

An algorithm is proposed for estimating axle loads of trucks moving over a bridge by measuring dynamic responses. The bridge was modeled by a beam structure in the current applications of the proposed algorithm. Among the state vectors, measured acceleration was used and displacement was computed from measured strain at the same location. Nodal force vectors were computed by using a ready-made database of equivalent nodal force transformation matrix. The algorithm was examined through simulation studies and laboratory experiments. The effects of measurement noise and velocity error were investigated through simulation studies.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.82-83
• /
• 2011

본 논문에서는 3경간 연속 사장교에 설치 된 계측장비에서 2010년 태풍 곤파스 당시 계측한 바람 및 교량응답 자료를 바탕으로 사장교의 버페팅 응답을 평가하였다. 계측 된 바람자료에서 스펙트럼 분석을 수행하고 그 결과를 버페팅 해석에 반영하여 실교량 거동을 예측하였다. 예측 된 교량의 거동은 실제 계측 된 값과 유산한 결과를 나타내었다.

• Geotechnical Engineering
• /
• v.1 no.1
• /
• pp.31-46
• /
• 1985

An extensive program of tunnel instrumentation has been Implemented in the construction of the Seoul Subway Line 3 and 4, in which the NATM was adopted as the main tunnelling technique. Among more than ten instrumented sections in the downtown area, five representative test sections were selected for analysis in this study, with an emphasis on the surface settlement and crown settlement. Variations of the surface and crown settlement. Variations of the governing factors, such as ground conditions, tunnel geometry, and construction conditions are described in this paper. Possible mechanisms for ground deformations occurring at different stages of tunnel construction are formulated, based on overall interpretation of the field observations and data obtained.

• Tunnel and Underground Space
• /
• v.16 no.6 s.65
• /
• pp.451-466
• /
• 2006

Analysis of slope behavior concerning the structural characteristics of field rock mass can be processed by virtue of borehole information of joint orientation and position acquired from DOM drilled core. Anticipated sliding potential of pre-failed rock slope is analyzed and the regional slope instability is investigated by inspecting the hazardous joints and blocks the traces of which is projected on the cut-face. Cross section has been set at the center of rock slope and the traces of both joints and tetrahedral blocks, which potentially can induce the slope failure, are drawn to investigate the failure modes and the triggering mechanism. Automated monitoring system has been established to measure the slope movement and especially, inclinometer has been installed inside DOM borehole to analyze the slope movement by considering the internal rock structure. Algorithms for predicting the slope failure time have been reviewed and the significance of heavy rainfall on the slope behavior has been investigated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.349-352
• /
• 2008

IPC girder is more prestressed and has smaller sectional area than the conventional PSC-I type girder due to incremental prestressing along the construction process. The continuous IPC girder bridge may have problems in serviceability and stresses at internal supports because it is very flexible. In this paper, The long-term behavior of the continuous IPC girder bridge is studied through long-term structural analysis and monitoring the deflections. The long-term behavior is monitored right before the introduction of 2nd prestressing that is the construction process different from the conventional PSC-I type girder bridge. The total station of high-precision was used in measuring the deflections. According to the monitoring result so far, the continuous IPC girder bridges does not show remarkable long-term behavior like severe camber or deflection and the measured deflections are very similar to the results of long-term structural analysis.

• The Journal of Information Technology
• /
• v.3 no.1
• /
• pp.1-8
• /
• 2000

Recently, many large structures have been constructed so it has been occurred small or big problem. One of problems in a safe construction is that behavior of underground is different between design and construction. Therefore, the purposes this study are that set up measuring equiptments in the site of construction and analyze information of measuring data for removing this problem, and measuring data use for similar method of construction in the engineering of ground.

• Tunnel and Underground Space
• /
• v.22 no.6
• /
• pp.393-402
• /
• 2012

A behavior of ridge-cut rock slope had been monitored by installing inclinometers and regional slope movement toward rear side of cut face was detected. To delineate the governing factors of slope behavior, especially backward slip of ridge-cut slope, petrographic characteristics of rock cores obtained from four drilled boreholes had been examined. BIPS images inside boreholes had been acquired and structural characteristics of slope rock had been studied. Mechanical properties of discontinuity planes distributed in the drilled core had been measured and the shear strength of coal seam imbedded-discontinuity planes also had been obtained by performing the direct shear test. Monitoring results of slope behavior had been analyzed by comprehensibly considering both the mechanical and structural characteristics of slope rock and coal seam-imbedded discontinuity planes, and the potential governance of coal seam and clay minerals embedded in the joint plane on the regional slope behavior has been also identified.

• Tunnel and Underground Space
• /
• v.14 no.4
• /
• pp.295-303
• /
• 2004

For the deep underground excavation site with the geological complexity of soft seam and hard rock, the numerical analysis and in-situ measurement on the behaviors of roadway and surrounding rock according to stepwise excavation of the steep soft seam are carried out. The strata behavior is modeled using elasto-plastic FEM considering the empirical failure criteria of Hoek ＆ Brown and the strain-softening model. Hydraulic pressure capsule, MPBX and tape extensometer are installed around the roadway for the in-situ measurement of rock stress and deformation. Despite the complexity of geology and excavation procedure, the elasto-plastic analysis considering the empirical failure criteria of Hoek ＆ Brown and the strain-softening model shows good agreement with the in-situ measurement. Comparison of numerical modeling with in-situ measurement enables to predict the behaviors of the roadway and to obtain design parameters for the excavation and support at depth.