• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.1005-1013
• /
• 2010

This study was conducted to assess the spray control of flash boiling with mixed fuel in consideration of HCCI (Homogeneous Charge Compression Ignition) engine condition. Mixed fuel existing in two phase regions can control the process of mixture formation under low temperature and density by using the spray resulting from flash boiling which is able to induce rapid evaporation of fuel spray as well as the evaporation of high boiling point component. Because HCCI engine injects the fuel early under ambient conditions, it can facilitate the chemical control of ignition combustion and physical control such as breakup and atomization of liquid fuel by flash boiling of mixed fuel which consists of highly ignitable light oil and highly volatile gasoline. This study was conducted by performing video processing after selected composition and molar fraction of the mixed fuel as major parameters and photographed Schlieren image and Mie scattered light corresponding to the flash boiling phenomenon of the fuel spray that was injected inside a constant volume vessel. It was found that flash boiling causes significant changes in the spray structure under relatively low temperature and density. Thus, we analyzed that the flash boiling spray can be used for HCCI combustion by controlling the mixture formation at the early fuel injection timing.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.6
• /
• pp.5-17
• /
• 2022

The performance of the relief wells installed for the purpose of controlling seepage of the dam embankment is affected by various parameters such as diameter, spacing, penetration rate, permeability coefficient of the ground, thickness of the foundation layer. Therefore, when the relief wells are adopted for the purpose of reducing seepage pressure, these parameters should be sufficiently reviewed to determine the installation specifications of the relief wells. This study evaluated the effect of the length of the geosynthetics blanket on the performance of the relief wells installed in the downstream part of the dam embankment with blankets in the upstream and downstream part of the dam embankment as countermeasure methods to control seepage of the dam embankment. In the relationship between the length of the upstream and downstream blanket and the discharge, the discharge of the relief wells decreases as the length of the upstream blanket increases, and on the other hand, the discharge of the relief wells decreases as the length of the downstream blanket increases. In the upper and lower blanket length-spacing relationship, as the length of the upstream blanket increases, the spacing of the relief wells increases and as the length of the downstream blanket increases, the spacing of the relief wells decreases. Therefore, when installing the relief wells in parallel with the blanket, it was found that increasing the length of the upstream blanket is more efficient than increasing the length of the downstream blanket in order to minimize the discharge of seepage discharge and to ensure economic feasibility by wider installation of the relief wells.

• Journal of Power System Engineering
• /
• v.7 no.1
• /
• pp.68-73
• /
• 2003

The purpose of this study is to develop a new proportional pressure reducing valve and to verify the validity of a new mechanism with pressure control pin. The dynamic characteristics of the object pressure reducing valve was studied by numerical analysis of the mathematical model. Also, static and dynamic characteristics of the new pressure control valve were tested with a testing system based on the test standard.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.73.2-73.2
• /
• 2010

휴대용 전자기기들의 소비전력 증가에 따라 2차전지에 비해 에너지 밀도가 높은 연료전지를 이용한 충전기의 필요성이 부각되고 있다. 대다수의 충전기는 On-Grid 방식으로 벅타입 컨버터를 이용한 감압 방식이었으나, 연료전지를 이용할 경우 승압식 컨버터를 통한 배터리의 충전이 요구된다. 또한 배터리는 일반 저항부하와 달리 큰 커패시턴스 성분을 가지고 있기 때문에 컨버터의 출력단에 인덕터가 없는 경우 큰 출력 리플전류를 유도하게 되어 시스템의 효율과 배터리의 수명에 좋지 않은 영향을 끼치게 된다. 또한 이를 해결하기 위해 절연형 감압 컨버터를 사용하는 경우 변압기 사용에 의한 부피 증가와 부가 소자의 사용에 따른 가격 상승을 피하기 어렵다. Cuk 컨버터는 주스위치의 ON/OFF 동작에 관계없이 출력으로 에너지가 항상 전달되며, 이상적으로 리플이 거의 존재하지 않아 충전용으로 적합하다. 또한, 승압 및 감압이 자유롭기 때문에 배터리의 정격전압에 상관없는 범용 충전기의 설계도 가능하다. 따라서 본 논문에서는 Cuk 컨버터를 이용하여 배터리 충전기를 설계하고, 그의 상태공간 모델링, 주파수 특성 해석 및 제어기 설계에 대해 기술한다. 제안된 제어 방식은 소형 연료전지 스택을 이용하여 실제 배터리를 대상으로 한 정전류 및 정전압 제어를 실행하여 그 성능 및 안정성을 검증한다.

• Journal of Aerospace System Engineering
• /
• v.11 no.3
• /
• pp.8-15
• /
• 2017

In this paper, an equivalent brake hydraulic circuit with a piezoelectric hydraulic pump was constructed, and load pressure control for better pressurization/depressurization characteristics was conducted. To understand pressurization/depressurization characteristics of the equivalent hydraulic circuit, the relation between the load pressure and the input voltage was revealed experimentally. Experiments were also conducted to observe effect of the solenoid valve on depressurization characteristics. In the pressurization experiment, it was validated that transient response time required to achieve desired load pressure may be reduced through voltage control to change pressurization gradient. By applying the valve on/off time control and voltage control, it was also possible to reduce response time in the depressurization process. Therefore, transient response time may be improved within 10ms for pressurization and within 30 ms for depressurization using the control technique suggested in this study. The load pressure control method proposed in this study is useful for controlling load pressure of a hydraulic brake system with the piezoelectric hydraulic pump.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.748-751
• /
• 2010

To launch rocket on launch pad, propellants and gases are charged into the rocket by remote control system. Using pneumatic pressure-reducing regulators, kinds of gases with various pressure levels are supplied into launch pad. As most of operations for launching the vehicle are remotely controled in the launch control room, pressure pulsations due to rapidly gas supply at the upstream of regulators can make the required operating pressure range missed and cause damage to the regulators. In this paper, the optimum design methods of pressure regulators of pressure-reducing system on launch pad using high-pressure gases were investigated to solve the aforementioned problems and for stable gas supply to launch pad.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.90-95
• /
• 2006

Pneumatic control systems have been mainly used as a high speed operating system. Therefore, state change of air in a control volume was assumed to be adiabatic change and, pneumatic control systems have been analyzed by using this assumption. Especially, when absolute value of pressure change in the control volume is small, there is a tendency to neglect effect of temperature change on pneumatic control system because temperature change owing to pressure change is small. In this study, an effect of temperature change of air on the decompression control process was analyzed by considering change of mass flow rate, and heat transfer characteristics between air in the chamber and the chamber wall. As a result, this study could confirm that a slight temperature change of the air in the pneumatic pressure control system can influence on the dynamic characteristics of pressure response, and pressure control performance.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2002.12a
• /
• pp.149-152
• /
• 2002

본 연구에서는 밸브의 입출력 류량 검출 센싱 장치 및 류량 성능 특성 곡선을 측정하는 소프트웨어를 개발하였다. 본 개발품은 기체 또는 액체의 양을 조절하는 밸브의 정밀한 제품을 생산할 수 있는 시스템이다. 멤버쉽함수의 최적한 폭을 자기동조에 의해 선정할 수 있었으며, 이를 이용하여 밸브의 압력 제어 성능을 보다 정밀하게 보정 할 수 있었다. 기체 또는 액체의 유량을 조절하는 감압 자동 조절밸브의 성능을 온라인으로 시험 할 수 있는 소프트웨어를 국산화하였다. 본 제품의 개발 결과 우수한 성능을 가진 감압 밸브 성능자동 보정 시험 검사용 소프트웨어임을 확인하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.15-23
• /
• 2019

In this study, an extinguishment model of a three-dimensional solid propellant rocket was developed by combustion and fast depressurization to control the thrust of a solid rocket. Computational fluid dynamics simulation was carried out to ascertain the change in flow patterns in the combustion chamber and the extinguishment process by using a pintle. An ammonium perchloride was used as the target propellant and the dynamic behavior of its major parameters such as temperature, pressure, and burning rate was predicted using the combustion model. The dynamic behavior of the combustion chamber was confirmed by fast depressurization from an initial pressure of 7 MPa to a final pressure of 2.5 MPa at a depressurization rate of approximately -912 MPa/s.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.3
• /
• pp.75-84
• /
• 1994

In general direct-operated pressure reducing valves have been gardly applied to a dynamic control system such as active suspension control because of their poor control stability. But they are more robust than pilot-operated type and do not need pilot control flow. In this paper development of a new direct-operated proportional pressure reducing valve for low-band type active suspension control is reported. By means of a special damper directly linked to the valve spool, the control stability could be effectively improved without drawback in response time. The linearity error was less than $\pm$3.5%. Applied to an experimental active suspension system the new valve showed the $-90^{\circ}$ phase delay at 4Hz with 20% sinusoidal signal input and could control the suspension system with almost same performance as that with a pilot-operated type valve.