• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.862-870
• /
• 1994

$Pb(NO_3)_2$, $Mg(NO_3)_2$ and $NbCl_5$ were used as starting materials and made into solutions. For $Pb(Mg_{1/3}Nb_{2/3})O_3$ composition, each solution measured was mixed and heated to $70^{\circ}C$ to resolved $PbCl_2$ precipitated at lower temperature coprecipitates were formed by adding oxine and ammonia gas under pH ranging 8 to 10, and the prepared coprecipitates were filtered and washed by distilled water. The $Pb(Mg_{1/3}Nb_{2/3})O_3$ powders were synthesized by calcination of coprecipitates at the temperature range of $700^{\circ}C$ to $1000^{\circ}C$, for 5hr. The average particle size of the synthesized powders showing spherical shape was $0.3{{\mu}m}$. The powders were formed to make pellets under pressure of $2000Kg/cm^2$, and the formed pellets were sintered at the temperature range of 1100 to $1200^{\circ}C$, for 5hr. The speciman sintered at $1200^{\circ}C$ showed theoretical density of 97.4%, dielectric constatnt of 17000 at 1kHz, and dielectric loss of 0.02% at 1kHz

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.7
• /
• pp.799-805
• /
• 2014

Recently, the regulations of the Local and Global for a variety of air pollution prevention has been enhanced by the steep rise in fuel oil prices. So, the appearance of Gas Fuelled Ships became necessary. In this study, we configured a regasification system which uses Eglycol water as a heating medium to evaporate before being supply fuel to the DF engine, then we analysed the system properties according to the Eglycol water mixing ratio. The results were as follows. When pressure, temperature, and flux of natural gas(NG) which are supplied to DF engines are uniformly kept, the higher mixing ratio of Eglycol is, the lower mixing specific heat of Eglycol water. And the cycle flux and electric power were 1.65 and 1.54 times more required. respectively, than water was used as the heating medium. Basic variables including mass flux according to the mixing ratio of Eglycol water, required electric power of operating fluid pumps, the temperature of natural gas which is supplied to the engine, and the heat exchanger's capacity were drawn from the gotten results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.6
• /
• pp.751-758
• /
• 2020

SCR technology, which uses urea-water as a NO_x reducing agent, has been widely used to reduce NO_x in marine diesel engines. However, as an alternative NO_x reducing agent, solid-phase ammonium carbamate has several advantages, such as low-temperature NO_x reduction performance and NH₃ storage capacity. This study presents a method for evaluating the purity of ammonium carbamate using EA, FTIR, and XRD to investigate the change in the material characteristics of ammonium carbamate when it is exposed to various temperature and pressure conditions. In this study, it was found that the purity of ammonium carbamate can be effectively evaluated via EA analysis. The FTIR analysis results confirmed that the properties of ammonium carbamate did not change even after repeated heating and cooling under thermal decomposition temperature conditions, which may be applied to the SCR system of marine diesel engines. Additionally, it was found that when ammonium carbamate was exposed to the atmosphere for a long time, it transformed into ammonium carbonate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.762-771
• /
• 1987

Friction welding is a fusion process in which the necessary heat is generated by clamping one of the two pieces to be welded in a stationary chuck and rotating the other at high speed with an axially applied load. It is essentially a variation of the pressure welding process but utilizes a novel heating method. In addition to the foregoing advantages, it has also been reported excellent for welding dissimilar materials. Therefore, this study reported on investigating the strength behavior for the frictionally welded domestic structural steel SM45C and SUS304. The results obtained by the experiments are as follows. (1) The highest tensile strength of the best friction welded specimen (B4) is about 3% lower than that of SM-45C base metal, and 9% lower than that of SUS304 base metal. The heat treated specimens (850.deg.C 1hr A.C) have almost same value of tensile strength. (2) The strain of SM45C base metal is 27.3% and that of SUS304 is 42%, that of the best friction welded specimen (B4) appeared as 11.9% which is about 50% lower than the base metal, so, this same phenomenon apeared in all the other welding conditions. (3) The bending strength of SM45C base metal is 123kgf/mm$^{2}$ and that of SUS304 is 127kgf/mm$^{2}$. The best specimen (B4) appeared as 121kgf/mm$^{2}$ which is almost same bending strength for both base metals. (4) The friction welded condition involving maximum strength is determined by P$_{1}$=8kgf/mm$_{2}$, P$_{2}$=22kgf/mm$_{2}$, T$_{1}$=10sec, T$_{2}$=2sec, and amount of upset 7.6mm. (5) The interface of two dissimilar materials are mixed strongly, and welded zone is about 1.03mm and also the heat affected zone is about 2.36mm at SM45C while about 1.85mm at SUS304, therefore the welded zone and heat affected zone are very narrow to compare with those of the other welding materials.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.793-798
• /
• 2017

In modern naval ships, an infrared signature suppression (IRSS) system is used to reduce the metal surface temperature of the heated exhaust pipe and high-temperature exhaust gases generated from the propulsion system. Generally, the IRSS systems used in Korean naval ships consist of an eductor, mixing tube, and diffuser. The diffuser reduces the temperature of the metal surface by creating an air film due to a pressure difference between the internal gas and the external air. In this study, design variables were selected by analyzing the shapes of a diffuser designed by an advanced overseas engineering company. The characteristics of the design variables that affect the performance of the IRSS were investigated through the Taguchi experimental method. A heat flow analysis technique for IRSS systems established in previous studies was used analyze the performance of the diffuser. The performance evaluation was based on the area-averaged value of the metal surface temperature and exhaust gas temperature at the outlet of the diffuser, which are directly related to the intensity of the infrared signature. The results show that the temperature of the exhaust gas was significantly affected by changes in the diameter of the diffuser outlet, and the temperature of the diffuser's metal surface was significantly affected by changes in the number of diffuser rings.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.55.2-55
• /
• 1998

다견정 심리판-거l르마늄(JXlly-SiGe)은 TFT(thin-film transistor)와 갇븐 소자 응용에 있어서 중요한 불칠이다 .. LPCVD (low pressure chemical vapor deposition) 방법으로 비정칠 SiGc (a-SiGe) 박막올 증 착시키고 고상결정화(SPC: solid-phase crystallization)시켜 poly-SiGc옹 얻는 것은 잘 알려져 있다. 그러 나 그러나 PF'||'&'||'pound;VD-SPC 방법올 이용한 poly-SiGc의 제조에 대해서는 아직 두드러지게 연구된 바 없다. 우리단 PF'||'&'||'pound;VD 방법으로 a-SiGc 박막올 증착시키고 고상캘정화시켜 poly-SiGc올 얻었 R며, :~ 결정성, G Gc 농도, 결정핍의 평끌 크기 눔올 XRD (x-ray diffraction) 방법으호 조사하였다. 특히 pr'||'&'||'pound;VD 증착시 가판온도,Gc 함유량 등이 고상화에 미치는 영향에 대해서 조사하였다. P PECVD 장치는 터보펌프콸 사용하여 71저진공이 2xlOlongleftarrow5 Torr에 이르렀다. 가판윤 SiOOO) 웨이퍼륜 사용하고 기판 온도는 약 150- 35()"C 사이에서 변화되었다. 증착가스는 SiH4, GcH4, 112 등흘 썼다. 증착 압력과 r.f 전력용 각각 O.25ToIT와 3W로 일정하게 하였다 .. Gc 함유량(x)은 x x=O.O-O.5 사이에서 변화되었다 .. PECVD모 증착된 SiGc 박막들은 고상결정화를 위해 $\theta$X)"(:: Nz 분위기에서 24시간동안, 혹은 5OO'C에서 4열간 가열되었다. 고상결정화 후 poly-SiGc 박막은 SiGc(Ill), (220), (311) XRD 피크들올 보여주었으며, 각 피 크들은 poly-Si에 비하여 왼쪽으로 Bragg 각이 이동되었고, Vegard’slaw에 의해서 x의 값올 확 인할 수 있었다. 이것온 RBS 결과와 열치하였다. 약 150-350'C 사이에서 변화된 기판온도의 범위 에서 증착온도가 낮올수콕 견정립의 크기는 대체로 증가하는 것으로 나타났다 .. XHD로 추정된 형 균 결정립의 크기는 최대 약 3$\alpha$1m 정도였다. 또한 같끈 샘플뜰에 대해서 기판온도가 낮올수록 증착속도가 증가함옴 확인하였다 .. Gc 함유량이 x=O.1에서 x=O.5로 증가함에 따라서도 결정립의 크기와 SiGc 증착속도는 증가하는 것으로 나타났다 .. Hwang [1] , Kim[2] 둥의 연구자들은 Gc 함유 량이 증가함에 따라 결정 립 크기가 캄소하는 것올 보고하였으냐, Tsai [3] 둥은 반대의 결과플 보 고하고 Ge 힘유량의 증가시 결정립 크기의 증가에 대해 Gc의 Si보다 낮은 융점 (melting point) 올 강조한 바 있다. 결정립 크기의 증가는 대체로 SiGe 중착속도의 증가와도 관련이 있음올 볼 때, poly-SiGc의 경우에도 polv-Si의 고상화에서와 같이 증착속도가 빠를수록 최종적언 결정럽의 크기가 커지는 것으로 이해될 수도 있다 .. PECVD 증착시 증착속도의 증가는 증착된 박딱에서의 무켈서도를 증 가시킬 수 있음올 고려하면, 이라한 결파플온 p이y-SiGc의 고상결정화에서도 ploy-Si의 고상결정 화에서와 마찬가지로 초기 박막에서의 구조직 무절서도가 클수록, 고상결정화 후 결정 립의 크기 가 커칠 수 있음올 보여준다고 생각휠 수 있다,

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.52.1-52.1
• /
• 2011

최근에 에너지 자원의 고갈이 다가오는 상황에서 태양전지 분야가 주목받고 있으며 이에 대한 시장이 급격하게 확대되고 있다. 그러나 현재의 태양전지는 주를 이루고있는 실리콘태양전지의 경우 원재료 수급이 불안정하여 가격 변동이 심하다. 따라서 이를 대체할 2세대 태양전지인 박막형 태양전지의 연구가 활발히 이루어지고 있다. 박막형 태양전지 중에서도 주목받고 있는 것은 Cu(In,Ga)$Se_2$(CIGS)박막 태양전지이다. CIGS는 Ga의 농도에 따라 1.02~1.68eV의 다양한 에너지 밴드갭을 갖는 직접천이형 반도체 물질이다. 또한 $1{\times}10^5cm^{-1}$의 높은 광흡수계수를 가지고 있으며, $450{\sim}590^{\circ}C$의 고온공정에서도 매우 안정하여 열화현상이 거의 보이지 않아 박막형 광흡수층 재료로서 적합하다. 흡수층을 제조하는 방법은 여러 가지가 있지만, 본 연구에서는 균일성이 뛰어나고 원료사용효율이 높은 sputtering 방법을 사용하였다. 그리고 결정화하기위해서 유독기체를 사용하는 셀.렌.화. (selenization) 방법 대신 전자빔을 조사하는 방법을 채택하였다. sputtering을 통한 CIGS precursor을 제조하기위해 2~3개의 화합물target을 사용하는데, 대표적인 방법으로 동시에 sputtering하는 co-sputtering 방법과 각각의 단일 층을 쌓아 제조하는 stack형으로 분류된다. 본 연구는 CIGS precursor를 제조하기 앞서 CuGa 단일 층만을 제조하여 공정조건에 따른 박막을 제조하였다. 제조된 CuGa 단일층은 전자빔 처리에 따른 영향을 알아보기 위해 전자빔의 세기와 공정시간을 달리하여 특성을 알아보았다. 실험에서는 Cu:75wt%,Ga:25wt% 조성의 target을 사용하여 공정 압력을 각각 10~1mTorr로 변화시키며 실험을 실시하였으며 공정 power는 50W, 70W, 100W로 변화 시키며 실험을 실시하였다. 이때 실험의 초기진공은 turbo-molecular pump를 이용하여 $1{\times}10^{-6}torr$ 이하로 하였으며, Target과 기판사이의 거리는 모두 같은 조건으로 고정하여 실험을 실시하였다. 박막의 균일성을 증가시키기 위하여 5 rpm의 속도로 기판을 회전하였으며 기판 온도는 가열하지 않고 상온에서 전구체를 증착하였다. 그 후 전자빔의 세기를 고정 시킨 후 전자빔 조사 시간을 조절하여 전자빔 조사 전후의 특성을 각각 분석하였다. 전기적특성은 Hall effect, 4-point probe, 구조적 특성은 SEM,EDS, XRD, XRF 를 이용하여 분석하였다.

• Korean Journal of Food Science and Technology
• /
• v.27 no.6
• /
• pp.827-833
• /
• 1995

Temperature distribution tests for a water cascading horizontal retort utilizing superheated water with overpressure as a heating medium were carried out under three different loading conditions, that is, empty(P-0), half-fully(P-3000) and fully(P-6000) loaded operating conditions. Tank volume and full loading capacity of sterilizer used for this study were about 5,900 liter and 1,140 kg(6000 pouches having 190 g weight each), respectively. Set point condition for sterilization was $122^{\circ}C$, 23 minutes and pressure was maintained in the range of $1.8{\sim}2.0\;kg/cm^2$ during sterilization. For each experiment, time-temperature data and F values were obtained from temperature microprocessor($F_0$ monitor). There were significant variations in the temperature distribution at different positions in the sterilizer. The temperature distribution was also affected by the pouch loading condition significantly. The application of the temperature distribution test to a product (retort pouched curry sauce) was conducted at the fully(P-6000) loading condition. Although heat transfer parameters($f_h\;and\;f_c$), and F values were varied with the position of sterilizer, sensory evaluation showed that the temperature distribution of the sterilizer used in this study didn't affect the quality of retorted curry sauce.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.1
• /
• pp.16-24
• /
• 1998

Recently Zr-based $AB_2$ type hydrogen absorbing alloy has received much attention as a negative electrode material for the Ni-MH batteries because of its high capacity. In this study $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ alloy was chosen and the effects of heat treatment and a partial substitution of the Mo in Mn site on the various electrode properties were investigated. The alloys was prepared by arc melting (as-cast sample). Some of them were heat treated at $1,100^{\circ}C$ for 4 hours. After this they were differentiated by the different cooling rates of slow cooling and quenching. Various electrode characteristics such as activation process, high rate dischargeability and self discharge characteristic were investigated with the three types of electrodes. It was found that heat treated alloys resulted in an increase in plateau flatness of P-C isotherms however both discharge capacity and high rate capability were decreased. And the partial substitution of Mo for Mn in $ZrV_{0.1}Mn_{0.7}Ni_{1.2}$ alloy improved the self-discharge characteristic without the loss of discharge capacity (300mAh/g).

• Food Science and Preservation
• /
• v.24 no.5
• /
• pp.631-637
• /
• 2017

The physiological properties of extracts from Hizikia fusiforme with different extraction methods (hot water extraction, autoclave extraction and high pressure extraction) were investigated. The amounts of substances related to polyphenol and flavonoids contents were the highest in autoclave extract (30.51 mg/g and 4.78 mg/g, respectively). The DPPH radical scavenging activity was the highest in the autoclave extract (81.80%) at the 5 mg/mL. Autoclave extract exhibited the strongest ABTS radical scavenging activity and reducing power among the three extraction methods. However, ferrous ion chelating, TBA reactive substances and xanthine oxidase inhibition activity of high pressure extract were higher than those of the other extracts. Additionally, the tyrosinase and elastase inhibition activities of high pressure extract with a concentration of 1 mg/mL were higher than those of the other extracts. These results suggest that extracts of Hizikia fusiforme have a potential to act as functional materials, and autoclave and high pressure extractions are superior to hot water extraction for enhancement of the biological activity.