• Solar Energy
• /
• v.17 no.2
• /
• pp.3-11
• /
• 1997

In conventional heat and vent dryer, both sensible and latent heat could not be recovered from the exhaust air, but this problem could be solved by introducing a heat pump to a conventional dryer, having a connection with cooling, dehumidifying and heating of heat pump. In this work, HFC134a as a substitute refrigerant of CFC12 adopted in heat pump and a batch type is also introduced. The variables affected on the system performance are holding temperature of a drying chamber, bypass air ratio, degree of superheat and refrigerant flowrate, etc. The moisture contents were decreased curvilinearly in the range of $86{\sim}75%$ on the wet basis. Under the constant drying temperature, the face velocity plays an important role to the drying performance. The COPs are increased in accordance with the air velocity, on the other hand the SMERs are gradually decreased.

• Food Science and Preservation
• /
• v.11 no.2
• /
• pp.250-256
• /
• 2004

The objectives of this study were to develop a new commercial grain cooler suited to domestic weather and post-harvesting conditions for paddy, and to evaluate the performance. A prototype grain cooler capable of cooling paddy of 200 tons within 24 hours was developed. The grain cooler was designed to control the refrigeration capacity from 0 to 100% by controlling the capacity of compressor with unloading solenoid valve and by changing the flow rates of hot refrigerant gas flowing into reheater and evaporator from compressor. And a controller with one chip microprocessor was developed to control temperature and relative humidity of cooling air. The maximum cooling capacity of the grain cooler was 35,284㎉/hr at condensing/evaporating pressure of 16.5/3.6 kgf/$\textrm{cm}^2$. Maximum flow rate of cooling air was 120 ㎥/min at static pressure of 279 mmAq. The total maximum required power was 22.8㎾, and total required energy was saved from 26.7 to 33.3% of maximum power depending on operating conditions. The coefficient of performance of refrigeration devices and total coefficient of performance of the grain cooler were 4.71 and 1.8, respectively.

• Journal of Sensor Science and Technology
• /
• v.5 no.4
• /
• pp.17-24
• /
• 1996

Planar multi-junction thermal converters were fabricated for precise measurements of the ac voltage and current by an ac-dc transfer method. A heater and a thermocouple array were fabricated onto a sandwiched membrane, $Si_{3}N_{4}$ (200 nm) / $SiO_{2}$ (400 nm) / $Si_{3}N_{4}$ (200 nm), a thickness of $0.8\;{\mu}m$ and a size of $2{\times}4\;mm^{2}$, which is supported by a surrounding frame. The NiCr heater is located at the center of the membrane vertically. Hot junctions of $48{\sim}156$ pairs of thermocouples (Cu-CuNi44) are located near or onto the heater, and cold junctions are located onto the silicon frame. Output of the thermal converters for 10 mA dc input was $76\;mV{\sim}382\;mV$ dependent on a model, and short term stability of the outputs was ${\pm}5{\sim}15\;ppm$/ 10 min with 5 mA dc input. Responsivity in air was in the range of $3.9{\sim}14.5V/W$. Responsivity of the model BF48 in air which has 48 thermocouples was 2 times or greater than that of 3 dimensional multi-junction thermal converter in vacuum which has 56 thermocouples. AC-DC transfer differences with an input of 10 mA or less were less than ${\pm}1\;ppm$ in the frequency range from 5 Hz to 2 kHz, and about $2{\sim}3\;ppm$ at 5 kHz and 10 kHz.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.4
• /
• pp.239-246
• /
• 2008

This research tried to find out the optimum fabrication method of calcined clay granules comprising zeolite. Kaolin clay and natural zeolite powder were used as raw materials of calcined clay, and silica stone powder was used for controlling the porosity of the granules. The granulation was performed with two kinds of granulators: a pan granulator and a high-shear mixer granulator. Various granules were fabricated by the mixing ratios and the rotation speeds of the granulators, and were heated from 400 to $700^{\circ}C$ at $100^{\circ}C$ interval. The crushing strength, pore size distribution, and CEC of the granules were measured. The evaluation method for the resistance of granules to human treading was created and the tests were conducted at dry and wet conditions. The resistance and crushing strength improved in proportion to the rotation speed of the granulator and the heating temperature, but the CEC decreased. The pellet made by the pan granulator did not have the strength against treading upon heating to below $700^{\circ}C$, but the pellet made by the high-shear mixer granulator endured the treading test upon heating to over $500^{\circ}C$

• Journal of the Korean Wood Science and Technology
• /
• v.8 no.1
• /
• pp.13-21
• /
• 1980

This experiment was carried out to investigate the effect of heating periods on the physical and mechanical properties of maple (Acer mono Max.) by oven heating and heating in water at 100$^{\circ}C$ for 0, 2, 4, and 6 days respectively. The results obtained are summarized as follows: 1. The green volume specific gravity due to oven heating decreased from 6 days of exposure, and that, due to heating in water decreased from 4 days of exposure. 2. The radial shrinkage due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 6 days of exposure. The tangential shrinkage due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 2 days of exposure. 3. The amount of water absorption due to oven heating decreased from 2 days of exposure, but that due to heating in water increased from 4 days of exposure. 4. The compressive strength pararelled to grain due to oven heating increased till 4 days of exposure but decreased from 6 days, and that due to heating in water decreased from 2 days of exposure. 5. The shearing strength pararelled to grain due to oven heating increased till 2 days of exposure, but decreased from 4 days of exposure, and that due to heating in water decreased from 4 days of exposure. 6. The bending strength due to oven heating increased till 4 days of exposure but decreased from 6 days, and that due to heating in water decreased from 6 days of exposure. The impact bending absorbed energy due to oven heating decreased from 4 days of exposure, and that due to hearing in water decreased from 2 days of exposure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.93.2-93.2
• /
• 2015

플라즈마를 포함한 반응성 가스 공정 분석용 사중극자 질량분석기의 필라멘트의 파손양상을 조사하였다. 또한 유전체 증착층이 이온원 성능에 미치는 영향을 분석하기 위하여 이온원의 일반적인 가동 전압 조건에서 Poisson방정식을 이용하여 전위를 수치 해석으로 구하였다. 사용중 파손된 필라멘트의 파단면을 주사전자현미경으로 관찰결과, 수직으로 절단되는 양상과 직경이 점차 작아지면서 erosion되는 두가지 양상을 보였다. 또한 파단면은 표면균열과 패시팅(faceting) 현상을 보였다. 필라멘트 사용시 가장 큰 문제는 패시팅(faceting)이다. 대부분의 결정에서는 다른 결정면보다 에너지 준위가 낮은 결정면이 존재한다. W 원자는 고온에서 확산 또는 증발하여 표면에서 다시 응축할 때 표면 에너지를 최소화하기 위한 독특한 평형 형상이 만들어 지는데 이것이 패시팅의 구동력이다. 이때 국부적으로 단면적이 감소하는 곳이 생기는데, 이 지점이 집중적으로 가열되고 증발이 가속화하여 파손된다. 파단면을 EDS 분석결과, 산화물을 포함한 F, Fe 및 C이 검출되었다. 이 F과 C는 공정중 사용된 CF4의 분해에 의한 것으로 생각되며, 파손된 필라멘트를 Ar 유도결합 플라즈마로 처리한 결과 이 F, Fe 및 C의 양이 감소하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.8
• /
• pp.112-119
• /
• 2002

Three dimensional numerical heat transfer analysis was carried out against periodically arranged fuel injectors of the liquid rocket engine. A finite volume method based on SIMPLE algorithm was adapted which gave a good agreement with the published results of the heat transfer problem of a backward facing step. The Nusselt number and pressure drop increased as the distance between the injector elements decreased. When the Reynolds number increased, the Nusselt number increased but nondimensionalized pressure drop decreased slightly.

• The Journal of the Acoustical Society of Korea
• /
• v.8 no.4
• /
• pp.5-12
• /
• 1989

In the clinical application of ultrasonic hyperthermia, selective heating of tumor is essential and thus precise control of ultrasonic intensity in both tumor and normal tissue is needed. In this paper, a hexagonal array transducer for ultrasonic hyperthermia is designed and manufactured of which focal point and focal region can be ocntrolled by the digital phase control circuit proposed by authors. Profiles of the focussed ultrasound beam in water and those of temperature in phantom were determined. The experimental and computed results are in good agreement.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.623-626
• /
• 2007

킬른형 열분해 반응기를 이용하여 혼합폐플라스틱의 열분해로부터 얻어진 고분자성분의 열적분해 특성에 관한 연구를 TGA와 GC-MS를 이용하여 수행하였다. 열적분해의 속도론적 연구는 $10{\sim}50^{\circ}C/min$ 사이의 여러 가열속도에서 비등온 질량감소 기술을 이용하여 수행하였으며 활성화 에너지 및 반응 차수와 같은 속도 상수들에 대한 정보를 얻기 위하여 문헌에 제시된 여러 가지의 속도론 해석방법을 이용하여 질량감소곡선 및 그 미분 값을 해석하였다. 또한 회분식 열분해 반응기를 이용하여 반응온도에 따른 액상 생성물의 수율변화를 고찰하였으며 GC-MS를 이용하여 액상 생성물의 반응온도 증가에 따른 특성연구를 수행하였다.

• Solar Energy
• /
• v.11 no.3
• /
• pp.9-20
• /
• 1991

Experiments for drying radish were carried out to analyze the drying characteristics and quality evaluation between solar heated-air drying and natural air drying system. Solar heated-air drying system consists of a small fan, a solar air heater and a tunnel dryer. Simulation model for thermal environments of solar collector was developed to investigate the effect of solar radiation and airflow rate on thermal performance.