• Composites Research
• /
• v.27 no.6
• /
• pp.254-259
• /
• 2014

In this study, a device and pressure press process that is able to substitute autoclave process is developed. This process complements disadvantages of autoclave process which are long process-time and high production cost. The developed device provides air pressure as well as the vacuum which are greatest feature of autoclave process. The device is sealed using hydraulic pressure to keep the air pressure inside the mold. The transfer of the heat is designed to be direct. The heating and pressure charging time are decreased by reducing the interior space. Tooling cost is reduced dramatically compared to autoclave process. Spring-back phenomenon is measured and compared. The temperatures of several parts of the mold during molding are measured. The fiber volume fraction of the parts molded by autoclave process and by the developed process are compared.

• Composites Research
• /
• v.20 no.4
• /
• pp.9-17
• /
• 2007

Powder metallurgy has been employed for the development of SiC particle reinforced aluminum metal matrix composites by means of hot isotropic pressing and vacuum hot pressing. A material model based on micro-mechanical approach then has been presented for the processes. Densification occurs by the inelastic flow of matrix materials during the consolidation, and consequently it depends on many process conditions such as applied pressure, temperature and volume fraction of reinforcement. The model is implemented into finite element software so that the process simulation can be performed enabling the predicted relative density to be compared with experimental data. In order to determine the performance of finished products, further tensile test has been conducted using the developed specimens. The effect of internal void of the materials on mechanical properties therefore can be investigated.

• Journal of Energy Engineering
• /
• v.2 no.1
• /
• pp.123-132
• /
• 1993

This work is focussed on the reduction of ethanol separation energy from alcohol fermented broth and categorized into the development of a computer program for the design of the pressurized/depressurized distillation process which has been regarded as one of the energy-reducing models for the conventional distillation process, the optimization of operating conditions of distillation towers by means of the developed program, and the evaluation of the total annual energy cost of pressurized/depressurized distillation columns compared with that of the conventional single distillation columns. The operating pressures are, in case of pressurized/depressurized distillation, 3103/760 mmHg, 3103/450 mmHg, 3103/160 mmHg, and in case of conventional distillation, 760 mmHg. The optimum reflex rations which the sum of the annual energy cost and the annual fixed cost for each process becomes minimum are 3.7475/2.9111 for the operating pressures of 3103/760 mmHg, 3.814/2.9712 for 3103/450 mmHg, 3.0783/2.2400 for 3103/150 mmHg, and 3.8544 for the atmospheric operating pressure. And the annual energy cost of pressurized/depressurized distillation process for the above-mentioned operating pressures is distributed between 42% and 47% of that of conventional distillation process.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.48-48
• /
• 2010

소형 공조장치용 냉매 압축기 부품인 기계식 제어 밸브는 에어컨 컴프레서의 핵심부품이고 년간 수백만 개가 국내에 수입된다. 이를 국산화 하기 위하여 진공로 속에서의 브레이징 공정이 수반되는 외국제품의 제조공정을 탈피하여 진공 속에서 DC 프로젝션 용접을 수행하는 기법을 개발하였다. 실린더 형상의 캡과 케이스를 맞대고 그 사이에 박판을 삽입한 상태에서 butt welding 방식으로 진행되는 본 공정에서는, 생산성이 높고 서보가압 장치를 사용하여 soft touch 를 구현하므로 프로젝션이 손상되지 않은 상태에서 통전이 시작되고 2 단 가압 및 프로파일 가압이 가능하므로 링(ring)형상의 너깃이 축대칭으로 안정적으로 형성되기 때문에 실린더 내부의 밀봉성능이 우수함을 확인하였다. 진공로 속에서 본 가압장치를 설치하여 간편한 방법으로 실린더 내부의 진공상태를 유지할 수 있기 때문에 진공로 속에서의 브레이징 공정이 적용되는 외국제품보다 생산성이 월등함을 알 수 있다. 본 연구에서 개발된 링 프로젝션(ring projection) 용접기법은 초소형 및 소형 실린더 형상의 부품 내부를 진공으로 유지해야 하는 산업현장에서 당장 적용될 수 있는 혁신적인 용접공정이라 판단된다.

• Membrane Journal
• /
• v.23 no.6
• /
• pp.460-468
• /
• 2013

This study reviewed optimum dosage rate of coagulant and ability to remove dissolved organic carbon without sedimentation in conventional water purification plant. It was confirmed that floc formated by pre-treatment process was broken by impeller of booster pump. Optimum dosage rate of coagulant was 4 mg/L (as PACl 17%) for floc formation through blend, coagulation and after passing through the pump when turbidity of raw water was less than 10 NTU. And average removal rate of dissolved organic carbon was 43% at that time. Maximum removal rate of dissolved organic carbon was 48%, even though coagulation rate was increased gradually until 8 mg/L (as PACl 17%). So removal rate of dissolved organic carbon is not much improved even if dosage rage of coagulant increase. TMP of PVDF (polyvinylidene flouride) pressurized MF process without pre-treatment operated at 0.54 bar and TMP of PVDF pressurized MF process with pre-treatment operated at 0.41 bar.

• Electrical & Electronic Materials
• /
• v.6 no.5
• /
• pp.446-453
• /
• 1993

초기충진압력이 서로 다른 시편에 가한 가압횟수와 열처리시간의 혼합공정이 임계전류밀도 특성에 미치는 영향을 관찰하기 위하여 power-in-tube방법으로 초전도 선재를 제조하였다. 일정 초기충진압력에서 테이프화를 위한 열처리 및 가압이 혼합공정횟수가 증가할수록 임계전류밀도가 증가하였다. 초기충진압력이 1000kg/$cm^{2}$에서 Bi-2223 고온상 체적비가 가장 높게 나타났고 결정립이 판상으로 성장되었을 뿐만 아니라 C축과 직각방향으로 잘 배양되어 있음을 관찰할 수 있었다. 특히 초기충진압력 1000kg/$cm^{2}$의 시편을 두께를 줄이기 위하여 3회 가압하고 450시간 열처리하였을때 임계전류밀도가 5800A/$cm^{2}$를 나타내었으며 이를 중심으로 500, 2500kg/$cm^{2}$이 양측단으로 가우시안분포를 보였다. 결론적으로 시편의 임계특성은 적정 초기충진압력, Bi-2223 고온상 체적비, 테이프화를 위한 가압횟수, 결정의 일방향배열, 결정립의 성장등에 강하게 의존함을 알 수 있었다.

• Electrical & Electronic Materials
• /
• v.7 no.1
• /
• pp.64-72
• /
• 1994

본 고는 현재 전기적 응용을 위한 수지 절연물의 진공/가압 수지-주형처리 분야에서 가장 앞선 기술과 연구개발력을 보유하고 있는 스위스의 Ciba-Geigy사와 최신의 진공성형 시스템을 개발, 생산하고 있는 독일의 Hedrich사 및 진공주형/자동가압 성형장비를 생산하는 스위스의 Vogel사 등을 최근에 방문하여 Epoxy, Polyurethane, Polyester 및 Silicone 수지 등의 수지절연시스템을 가지고 구조적으로 기포가 없으며 전기적, 기계적, 열적특성이 매우 우수하고 매끄러운 표면이 요구되는 수지 mold제품을 생산하는데 적용되고 있는 진공 수지-주형처리기술의 현황과 아울러 경화시간을 크게 단축시켜 생산자동화가 가능한 최신의 자동가압겔화(Automatic pressure gelation)/주입몰드공정(Injection molding process)의 특징 및 기술개발현황에 대해 파악한 내용을 소개하고자 한다.

• Korean Journal of Materials Research
• /
• v.8 no.3
• /
• pp.245-251
• /
• 1998

Bi-doped n-type PbTe thermoeletric materials were fabricated by mechanical alloying and hot pressing. The intering characteristics and thermoelectric properties of the hot- pressed PbTe were characterized and compared with the properties of the specimens prepared by meltingigrinding method. The hot-pressed PbTe specimens fabricated by mechanical alloying exhibited more negative Seebeck coefficient, higher electrical resistivity and lower thermal conductivity. compared to ones prepared by meltingigrinding. The maximum figure-of-merit increased and the temperature for the maximum figure-of-merit shifted to lower temperature for the specimens fabricated by mechanical alloying. When hot pressed at $650^{\circ}C$, 0.3 wt% Bi-doped PbTe fabricated by mechanical alloying and meltingjgrinding exhibited maximum figure-of-merits of $1.33\times10^{-3}/K$ at $200^{\circ}C$ and $1.07\times10^{-3}/K$ at $400^{\circ}C$ respectively.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.333-335
• /
• 2004

현재 저항 점 용접 공정에서 기존의 공기 가압 장치에서 서보모터를 이용한 서보 가압 장치로 변화가 진행되고 있다. 특히 마이크로 접합부의 경우 그 대상부가 미소ㆍ미세하기 때문에 접합부의 두께, 변형량, 접합후 전기 저항의 크기 둥이 크게 문제가 될 수 있다. (중략)

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.239-246
• /
• 2013

Principle of foamed glass manufacturing process first starts with putting vitreous material powder into a mold. After the foaming calcination, foamed body should be annealed after separation from the mold. For this reason, existing manufacturing process could not be a continuous type process. In this study, in order to develop a continuous production process of foamed glass, the possibility of new foam glass manufacturing process was investigated by foaming calcination of the compact body obtained from compression-molding of vitreous raw materials in stead of using a mold. Through the experimental results of the foaming calcination of the compact body with adding various foaming agents such as $Na_2CO_3$, $CaCO_3$ and petroleum coke, into hydrated soda-lime vitreous raw materials, it was shown that developing a continuous process without using any molds for manufacturing foamed glass would be possible.