• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.606-612
• /
• 2022

Relatively high indoor CO₂ concentration (>1,000 ppm) has a negative impact on human health. In this work, indoor CO₂ adsorbent was developed by impregnating KOH or K₂CO₃ on commercial activated carbon, named as KOH/AC and K₂CO₃/AC. Commercial activated carbon (AC) showed relatively high BET surface area (929 m²/g) whereas KOH/AC and K₂CO₃/AC presented lower BET surface area of 13.6 m²/g and 289 m²/g. Two experimental methods of TGA (2,000 ppmCO₂, weight basis) and chamber test (initial concentration: 2,000 ppmCO₂, CO₂ IR analyzer) were used to investigate the adsorption capacity. KOH/AC and K₂CO₃/AC exhibited similar adsorption capacities (145~150 mg_CO2/g), higher than K₂CO₃/Al+Si supports adsorbent (84.1 mg_CO2/g_sample). Similarly, chamber test also showed similar trend. Both KOH/AC and K₂CO₃/AC represented higher adsorption capacities (KOH/AC: 93.5 mg_CO2/g K₂CO₃/AC: 94.5 mg_CO2/g_sample) K₂CO₃/Al+Si supports. This is due to the KOH or K₂CO₃ impregnation increased alkaline active sites (chemical adsorption), which is beneficial for CO₂ adsorption. In addition, the regeneration test results showed both K-based adsorbents pose a good regeneration and reusability. Finally, the current study suggested that both KOH/AC and K₂CO₃/AC have a great potential to be used as CO₂ adsorbent for indoor CO₂ adsorption.

• Resources Recycling
• /
• v.19 no.2
• /
• pp.45-53
• /
• 2010

During the biomass gasification, tar generation is typically accompanied, which causes many problems, such as pipe plugging and equipment fouling. In the experiments, activated carbon was applied to the upper reactor of the two-stage gasifier in order to remove the tar generated during gasification. In addition, the effects of the upper-reactor temperature and equivalence ratio on the producer gas characteristics (composition, tar content and lower heating value) were investigated. To investigate the effect of the upper reactor-temperature, experiments were performed at 743, 793, $838^{\circ}C$, respectively. To examine the influence of the equivalence ratio, a comparison experiment was carried out at a equivalence ratio of 0.17. In all experiments, tar contents in the producer gases were below $2mg/Nm^3$. The maximum LHV of the producer gas was above $10MJ/Nm^3$, which is much higher than the typical LHV($3\sim6MJ/Nm^3$) in the air gasification of biomass.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.57.1-57.1
• /
• 2012

금속을 용해 응고시킬 때 생성되는 소위, 주조 결함이나 소결금속 내의 기공은 재료의 성능이나 강도를 현저하게 낮추는 결함으로서 예전부터 기피되어 왔다. 또한, 재료공정에 있어서도 여하의 기공이나 기포가 없는 치밀한 고강도 및 고기능성 재료를 개발하는 것에 최대한의 주의와 관심을 기울여 왔다. 반면에 자연계의 천연물이나 인공물을 둘러보면 그 대부분이 다공질임을 쉽게 눈치챌 수 있다. 예를 들어 목재, 지엽 등의 생물을 시작해서 콘크리트 등의 인공물, 우리 체내의 뼈도 전형적인 다공질구조로 구성되어 있다. 이러한 구조로부터 재료의 재질제어 이외에 구조제어라는 새로운 어프로치를 고려할 수 있고, 최근 들어, 금속재료에 있어서도 이러한 다공질 구조에 관한 연구가 활성화되어 충격흡수재, 생체재료, 베어링재료 등의 다양한 응용이 전개되고 있다. 원주상의 방향성 기공을 갖는 로터스 금속의 제조 원리는 용융금속의 높은 가스용해도와 고체금속의 낮은 가스고용도의 차이를 이용하여 응고할 때 고용되지 않는 가스원자가 기포를 형성시키는 것이다. 수소용해도는 모든 금속에 있어서 온도상승에 따라 증가하지만 융점에 있어서 용해도의 불연속적 증가를 나타내며 응고할 때 고액계면에서 다량의 가스를 방출하고 기공 생성을 야기한다. 특히, 고 액상에 있어서 수소용해도 차가 큰 마그네슘, 니켈, 철, 동 등은 기포를 생성하기 쉽다. 또한 기공의 배열구조를 제어하기 위해 일방향응고법를 이용하여 기공에 방향성을 부여한다. 외관상 기공구조가 연근뿌리를 닮은 것으로 부터 로터스 금속이라는 명칭이 널리 알려져 있다. 이와 같은 제조방법에 의해 로터스 금속은 기공 방향, 기공크기, 기공률을 자유롭게 제어할 수 있고 우수한 기계적 성질이 기존의 발포금속, 소결금속과 전혀 다른 특성을 가지고 있다. 이러한 기공구조는 용해온도, 응고속도, 분위기 가스압, 불활성가스와의 혼합체적비 등의 제어를 통해서 조절할 수 있다. 이와 같이 제조한 방향성 다공질금속은 BT (인플란트, 생체적합성, 저탄성, 경량), ST (초음속기엔진부품, 경량), IT (고성능수냉모듈), ET(고온촉매, 필터)의 분야로의 응용을 기대한다.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.28-36
• /
• 2018

Adsorption experiments of three target gases such as acetone, benzene, and methyl mercaptan (MM) were carried in a continuous reactor using the activated carbon prepared from waste citrus peel. In a single gas system, the breakthrough time obtained from using the activated carbon (WCAC) prepared from waste citrus peel. In a single gas system, the breakthrough time obtained from the breakthrough curve decreased with increasing the inlet concentration and flow rate, but increased with respect to the aspect ratio (L/D). Adsorbed amounts of the target gases by WCAC increased as a function of the inlet concentration and aspect ratio. However, adsorbed amounts with the increase of the flow rate were different depending upon target gases. Results from the breakthrough time and adsorbed amount showed that the affinity for WCAC was the highest in benzene, followed by acetone and then MM. On the other hand, in the binary and ternary systems, the breakthrough curve showed a roll-up phenomenon where the adsorbate having a small affinity for WCAC was replaced with the adsorbate with a high affinity. The adsorption of acetone on WCAC was more strongly affected when mixing with the nonpolar benzene than that of using sulfur compound MM.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.3
• /
• pp.175-181
• /
• 2015

Activated carbon impregnated with polyethyleneimine (PEI) was evaluated as a functionalized adsorbent for $CO_2$ capture. The $CO_2$ adsorption characteristics of the adsorbents was undertaken using GC/TCD, BET surface area and FT-IR. A series of adsorbents were synthesized by impregnating 10, 30, 50 wt% of PEI on activated carbons and were investigated $CO_2$ adsorption capacity at high and low adsorption temperature. The $CO_2$ adsorption capacity at $20^{\circ}C$ and $100^{\circ}C$ was as follow: AC > PEI(10)-AC > PEI(30)-AC > PEI(50)-AC at $20^{\circ}C$ and PEI(10)-AC > PEI(30)-AC > PEI(50)-AC > AC at $100^{\circ}C$. Adsorption capacities of amine functionalized AC was lager than virgin AC at high temperature due to chemisorption by amino-group content. From the results, the PEI(10)-AC showed one of the most promising adsorbents for $CO_2$ capture from flue gas at high temperature.

• Applied Chemistry for Engineering
• /
• v.19 no.4
• /
• pp.445-451
• /
• 2008

In order to regenerate the activated carbon polluted by volatile organic compounds (VOCs) using microwave, adsorption and desorption characteristics of benzene over activated carbon (AC) coated with insulating materials were investigated. Physical characteristics of activated carbon and insulator-coated ACs were investigated by means of $N_2$ gas adsorption and scanning electron microscopy (SEM). The amount of VOC adsorbed showed a positive relationship with the specific surface area of the ACs, and spark discharge over insulator-coated ACs did not occur. Potassium silicate (PS) was the best binder for coating of insulating materials on AC. Amount of benzene desorbed by microwave irradiation was dependent on output power of microwave. Nearly same performance was obtained even though the adsorption-desorption operation under microwave irradiation was repeated 5 times. Finally, it was known that the microwave heating was a very effective mean for regenerating the polluted AC.

• Applied Biological Chemistry
• /
• v.16 no.3
• /
• pp.146-165
• /
• 1973

Crop damages caused by sulfur dioxide poisoning were studied with respect to physiology of lesion, yield loss and prevention measures. The results are summarized as follows; 1. On the physiology of injury: The sulfur dioxide gas did no: affect the pH and $E_h$ values of the tested leaf juice of plants. Peroxidase activity was inhibited just after sulfur dioxide treatment but gradually recovered to normal after 10 hours. Methanolic chlorophyll solution was instantaneously and irreversibly bleached by the addition of sulfur dioxide gas with no evidence of pheophytin formation. It seems that chlorophyll forms colourless addition product or is reduced to colourless form with either sulfur dioxide gas or sulfurous acid. Chlorophyll in the chloroplast was also bleached by the sulfur dioxide treatment, as in the case of methanolic solution of chlorophyll, except that the rate of bleaching was rather slow, requiring 1-2 hours. It appears that the most inflicting cause of sulfur dioxide gas to plants may be the destruction of chlorophyll by the poisoning gas. 2. On the effects to crop yield: The crop yield losses were proportional to the concentration of inflicting sulfur dioxide gas. The order of tolerence of the crops to the sulfur dioxide gas was as follows - chinese cabbage being the most susceptible; wheat, paddy rice, barley, soybean, welsh onion, radish and chinese cabbage. The crucifer crops were generally found more susceptible than other crops studied. With respect to the growing stages of crops exposed to sulfur dioxide gas, it was found that the flowering stage was the most susceptible fellowed by panicle forming, milky and tillering in the decreasing order of susceptibility. 3. On the preventive measures of yield losses: Soil applications of potassium, wollastonite, lime or spray of lime water were effective to prevent yield losses from sulfur dioxide fumigation of paddy rice, barley, and soybeans. The most responsive treatment was lime water spray for all crops tested. In case of sulfur dioxide fumigated paddy rice, the lime water spray also increased carbon assimilation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.7
• /
• pp.662-669
• /
• 2017

Military rotary aircraft are heavily exposed to projectile environments due to their mission characteristics, and fires caused by fuel leaks after shooting are linked directly to the loss of human life. To improve the survivability of pilots and crews, the fuel tank in rotary aircraft must have gunfire resistance and anti-explosion characteristics. Gunfire resistance can be satisfied by applying a self-sealing cell to a fuel tank. Anti-explosion can be satisfied by reducing the oxygen concentration in an explosive area and suppressing the generation of combustible fuel vapor by minimizing the evaporation rate of the fuel by heat. A Korean utility helicopter applies anon-board inert gas generation system to meet the anti-explosion requirements for ballistic impact. The generator fills the fuel tank with an inert gas and reduces the oxygen concentration. This paper describes the overall development process of the OBIGGS developed in accordance with the localization process of weapon components. OBIGGS was developed/manufactured through domestic technology, and the performance was found to be equal to or better than that of the existing products through single performance tests and aircraft mounting tests.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.30 no.4
• /
• pp.56-60
• /
• 2001

경험에 의하면 앞에서 언급한 장비의 사용, 규율, 규제된 용제의 사용, 기름 페인트 사용의 억제, 그리고 엄격한 페인트 과정을 따르는 것에 의해 잠수함내의 탄화수소 농도를 100만분의 1 또는 2 수준으로 유지할 수 있다. 예방책으로는 세심한 관찰, 선체내로 들여오는 모든 물질의 기록 그리고 규제된 물질의 사용 시간, 장소 및 양의 제어이다. 이러한 점들은 잠수함 내부를 안전하고 건강한 환경으로 설계하기 위하여 활용될 수 있는 자료들이다. 잠수함 내의 공기질은 적외선 분광 광도계, 질량 분광계, 상자성(paramagnetics), 열전도율, 광이온화 그리고 열량 검사에 의해 분석될 수 있다. 분석된 결과는 과거의 데이터와 비교되어 활성탄충의 교체등을 포함하여 유지 관리의 자료로 활용된다. 이러한 원리를 이용한 다양한 계측기가 선체 내의 대기 상태를 분석하기 위하여 사용된다. 중앙 대기 측정기, 추적 가스 분석기, 수소 탐지기, 이동형 대기 모니터, 이동형 산소 분석기, 탄광 안전 지시계, 열량 분석관, 탐지 펌프 시험기가 사용된다. 이러한 계측기는 잠수 전 또는 후에 사용된다. 계측기는 화재 발생시 영향을 받지 않은 공간 또는 냉매가 충전되는 장소에 사용된다. 오늘날 여러 종류의 특별한 잠수함이 존재한다. 정찰 업무를 통해 세계 평화를 유지하고 특별한 임무를 수행하는 것보다 덜 복잡한 목적을 지닌 잠수함도 있다. 그러나 선원들이 안전한 내부 환경 속에서 바다 속을 항해하고 계속 그 응용 범위를 확장하기 위하여 앞에서 언급한 장비들 또는 그 변형들이 사용되어야 한다.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.574-581
• /
• 2008

The optimum regeneration conditions for the regeneration of three way spent catalysts (TWCs), which were taken from automobiles with different driving conditions, were investigated to evaluate the suitability as alternative catalysts for removing VOCs. The spent catalysts were washed with five different acids ($HNO_3$, $H_2SO_4$, $C_2H_2O_4$, $C_6H_8O_7$, and $H_3PO_4$) to remove contaminants and examine the optimum conditions for recovering the catalytic activity. The physicochemical properties of spent and its regenerated TWCs were evaluated by using nitrogen adsorption-desorption isotherms, XRD, and ICP. The relative atomic ratios of contaminants and platinum group metals (PGMs) of the spent TWCs were greatly dependent on the placed positions. The main contaminants formed were lubricant oil additives and metallic components. Also, the regeneration treatment increased the PGMs ratio, BET surface area, and average pore diameter of TWCs. The catalytic activity results indicated that the spent TWCs have the possibility for removing VOCs. Moreover, the employed acid treatments greatly enhanced the catalytic activity of the spent TWCs. Especially, nitric and oxalic acids provided the most improvement in the catalytic behavior. The catalytic activities of the regenerated TWCs were significantly influenced by the containing platinum ratios rather than the removal ratios of contaminants and the changes in the structural properties offered by the acid treatments.