Journal of Korean Society of Environmental Engineers
/
v.22
no.2
/
pp.291-302
/
2000
This experiments have been made to develop of manganese-based sorbent for the removal of hydrogen sulfide from hot coal gases. Manganese-based sorbent were tested in an ambient-pressure fixed-bed reactor to determine steady state $H_2S$ concentrations, breakthrough times and feasibility of the sorbent when subjected to cycle sulfidation and regeneration testing. Effects of particle size of sorbent, temperature of sulfidation, regeneration temperature and regeneration characteristics on the $H_2S$ removal efficiency were investigated. Experimental results showed that the $H_2S$ removal efficiency was optimal when the temperature was about $800^{\circ}C$ and the smaller particle size, the better $H_2S$ removal efficiency but in the range of 0.214~0.631mm didn't influence it much. The equilibrium constant(K) is represented as a log(K)=3.396/T-1.1105 and the utilization efficiency of sorbents was about 92% at $800^{\circ}C$. Regeneration in air produced $SO_2$ concentration as high as 8.5% at $800^{\circ}C$, 8.4% at $850^{\circ}C$, and 8.8% at $900^{\circ}C$ and may be used in sulfuric acid production.
Journal of the Korean Society for Marine Environment & Energy
/
v.10
no.2
/
pp.112-117
/
2007
This study aims to develop an alternative energy like oil made from marine organic waste by marine products waste, spent fishing nets. There are already many commercial examples and case studies based on the petroleum industry-refuse plastic or refuse tire, however, it is rare that a research developing alternative energy from food waste and organic waste. Therefore, this study investigated the oil made from thermal decomposition under the high temperature and high pressure condition, and examined the possibility for commercial use by testing its own characteristics. A bio-oil from thermal decomposition at $250^{\circ}C$ and 40 atm was hard to remove impurities because of its high viscosity, showed lower caloric value than heavy oil, and generated various gases which were not appropriate for the use of fuel. It is noticeable that thermal decomposition was occurred at $250{\pm}5^{\circ}C$ using steam pressure, which much lower compared to the existing method of thermal decomposition, more than $500^{\circ}C$. Since the high viscosity of bio-oil, it is necessary a further study to use as liquid fuel.
Proceedings of the Korea Technology Innovation Society Conference
/
2004.11a
/
pp.101-113
/
2004
본 연구는 기술혁신파급경로를 결정하는 국가 간 무역역할에 대한 실증적인 분석을 목적으로 한다 이 연구목적을 위하여, 최근 자료인 1980년부터 2003년까지 15개 OECD국가를 대상으로 자국의 기술혁신을 결정하는 중요한 변수로 알려진 자국 R&D축적 및 무역대상국의 R&D축적자료를 구축하였으며, 이를 무역지수인 쌍방간에 수출 및 수입량을 경제규모로 나눈 가중지수를 이용하여 유입된 R&D축적량을 구축하였다. 또한 대상변수들의 기술혁신파급역할에 대하여 최근 논의되고 있는 비정상적 패널기법을 이용하여 분석하였다. 최근 제안되고 있는 비정상적 패널기법을 이용하여 국제 간에 기술혁신파급경로를 분석한 결과를 간단하게 요약하면, 다음과 같다. 첫째, 분석대상변수들은 비정상성을 갖는 것으로 나타났다. 둘째, 그러나 장기적으로 분석대상변수들이 서로 균형상태를 나타내는 공적분관계에 있음을 알 수 있었다. 셋째, 국가 간에 기술혁신파급경로의 방향과 정도를 파악하기 위하여 패널 공적분계수를 추정하였으나, 설정함수형태에 따라서 여러 가지 상반된 실증결과가 나타났다. 따라서 기존 연구Coe et al., 1995, Keller, 1998, Kao, et al., 1999 그리고 Funk, 2001]의 분석결과 및 그 시사점들이 서로 다른 이유는 분석대상변수들의 선택차이뿐만 아니라, 기술혁신경로에 대한 설정함수형태에 따라서 서로 다른 분석결과가 나타날 수 있는 가능성을 보여준다. 본 연구에서 나타난 분석결과의 시사점을 보면, 국가 간에 기술혁신파급경로분석은 기술혁신파급을 결정하는 매개변수선정도 중요하지만, 결정된 설명변수들 사이에 어떤 기술혁신파급에 관한 연관관계가 존재하는지에 대한 실증분석 즉 파급경로분석도 매우 중요함을 보여준다. 이러한 파급경로분석에는 기존의 선형가정뿐만 아니라 비선형가정을 이용한 기술파급경로분석을 통한 시사점제안이 요구된다.관적인 시스템을 제공하는 것이다.가 생성된다. $M_{C}$에 CaC $l_2$를 첨가한 경우 $M_{C}$는 완전히 $M_{Cl}$ 로 전이를 하였다. $M_{Cl}$ 에 CaC $l_2$를 첨가하였을 경우에는 아무런 수화물의 변화는 발생하지 않았다. 따라서 CaS $O_4$.2$H_2O$를 CaC $O_3$및 CaC $l_2$와 반응시켰을 때의 AFm상의 안정성 순서는 $M_{S}$ < $M_{C}$< $M_{Cl}$ 로 된다.phy. Finally, Regional Development and Regional Environmental Problems were highly correlated with accommodators.젼 공정을 거쳐 제조된다는 점을 고려할 때 이용가능한 에너지 함량계산에 직접 활용될 수는 없을 것이다.총단백질 및 AST에서 시간경과에 따른 삼투압 조절 능력에 문제가 있는 것으로 보여진다.c}C$에서 5시간 가열조리 후 잔존율은 각각 84.7% 및 73.3%였고, 질소가스 통기하에서는 잔존율이 88.9% 및 81.8%로 더욱 안정하였다.8% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에 적응된 개체의 면적보다 유의성
AISI 4600 Iron powder was mixed with 0~1.0% phosphor as F$e_2$P powder and/or 0~0.8% carbon as graphite powder in rotating mixer. Mixed powder was pressed 800MPa in double-punch mould. Compacts were sintered at 115$0^{\circ}C$for 30 min. in vacuum or mixed hydrogen and nitrogen gas. Sintered compacts were ground and polished, and etched by 2% nital etchant. The microstructure was observed by image analyzer and optical microscope. Density and microhardness were tested by ASTM B3l2 and Microvickers hardness tester. The results obtained were as follows : (1) As the amount of F$e_2$P powder increased, sintered microstructure showed more densified effect and the grain size was larger. (2) The shape of pore was rounded and the number of pore was decreased by F$e_2$P addition. But mean pore size was larger with F$e_2$P content. (3) Simultaneous alloying addition of F$e_2$P and graphite brought about larger grain growth than respective addition. (4) Sintering atmosphere did not affect the microstructure. (5) Hardness of sintered compact increased with phosphrous and carbon content.
Silicon carbide candle filters for the pressurized fluidized bed combustion system were fabricated by extrusion process. Carbon black was added to control the porosity. Inorganic additives such as clay and calcium carbonate were added to exhibit appropriate strength. Silicon carbide layer with a finer pore size (mean pore diameter ~$10{\mu}m$) was coated on the silicon carbide support layer (mean pore diameter ~$47{\mu}m$, porosity ∼40%). After that, the filter was sintered at 1400${\circ}C$ in air. We evaluated the filtration performances of the filter at 500${\circ}C$ and $5kgf/cm^2$ of pressure. As a result, high separation efficiency, >99.999% was measured. It is expected that silicon carbide candle filter can be successfully used for the pressurized fluidized bed combustion system.
80년대 초반에 등장한 퍼스널 컴퓨터에서부터 90년대에 급격히 확산된 클라이언트/서버 환경에 이르기까지 분산 컴퓨팅은 관리가 어렵다고 증명되었다. IBM의 Tivoli나 HP의 OpenView 등을 포함한 거대한 엔터프라이즈 관리 시스템 산업이 이러한 표면상의 극복하기 힘든 법칙처럼 여겨지는 것이 그 증거라고 하겠다. 이 후 무선의 개념이 등장했다. NOP World Technology가 Cisco사를 위해 2001년에 시행한 조사에 의하면 최종 사용자는 무선랜을 사용함으로써 생산성이 최고 22% 향상되었고 조사대상의 63%가 일상적인 직무에서 정확도가 향상되었다. 이 모든 것은 투자대비수익(ROI) 계산상 사용자 당 $550 해당한다. 현재 이동성과 IT 관리 기능의 딜레마를 동시에 고려하며 저렴한 몇몇 솔루션들이 소개되고 있다. 본 논문에서는 분산 컴퓨팅의 다음 진화 단계인 무선 네트워킹과 관련된 문제를 해결할 수 있는 혁신적이고 전체적인 접근법을 소개한다. 본 논문에서는 무선 컴퓨팅과 보안의 본질 및 무선랜이라는 새로운 컴퓨팅 패러다임으로 인하여 파생되는 운영과 관리의 어려움을 소개한다. 이러한 환경이 정의되면 본 논문은 이해하기 쉬운 5x5 레이어 매트릭스를 바탕으로 각 레이어의 독특한 본질을 고려한 혁신적인 무선랜 관리 방법에 대해 설명한다. 마지막으로 무선 네트워킹, 컨버젼스, 궁극적으로 분산 컴퓨팅만이 가지는 문제점을 해결할 수 있는 Red-M의 백 오피스 애플리케이션에 기반한 솔루션을 소개한다. 본 논문의 목표는 Red-M의 성공에 관한 두 가지 중요한 과정을 설명하고자 함이다. 이는 안전한 무선 네트워크 제어에서 비롯되는 무선 환경이 약속하는 장점들을 고루 제공하는 것과 나쁜 의도의 사용자를 차단할 뿐 아니라 올바른 사용자와 또한 나머지 일반 사용자를 총체적으로 관리할 수 있는, 안정적이고 확장 가능하며 직관적인 시스템을 제공하는 것이다.가 생성된다. $M_{C}$에 CaC $l_2$를 첨가한 경우 $M_{C}$는 완전히 $M_{Cl}$ 로 전이를 하였다. $M_{Cl}$ 에 CaC $l_2$를 첨가하였을 경우에는 아무런 수화물의 변화는 발생하지 않았다. 따라서 CaS $O_4$.2$H_2O$를 CaC $O_3$및 CaC $l_2$와 반응시켰을 때의 AFm상의 안정성 순서는 $M_{S}$ < $M_{C}$< $M_{Cl}$ 로 된다.phy. Finally, Regional Development and Regional Environmental Problems were highly correlated with accommodators.젼 공정을 거쳐 제조된다는 점을 고려할 때 이용가능한 에너지 함량계산에 직접 활용될 수는 없을 것이다.총단백질 및 AST에서 시간경과에 따른 삼투압 조절 능력에 문제가 있는 것으로 보여진다.c}C$에서 5시간 가열조리 후 잔존율은 각각 84.7% 및 73.3%였고, 질소가스 통기하에서는 잔존율이 88.9% 및 81.8%로 더욱 안정하였다.8% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에 적응된 개체의 면적보다 유의성있게 나타났다. 해수(海水)에 적응(適應)된 틸라피아의 신단위(腎
Kim, Jaewon;Choi, Junhyung;Choe, Keumbong;Sim, Sumin;Lee, Dae Sung
Tunnel and Underground Space
/
v.27
no.1
/
pp.26-38
/
2017
In this study, bedding rock permeability was measured using Berea sandstones with three different beddings. The fracture permeability was also measured using tight sandstone with two different fracture regimes considering in-situ stress conditions. The Berea sandstone with vertical, horizontal and non-bedding was used to analyze evolution of permeability upon in-situ stress conditions. In order to describe applied effective stress around rock in underground, the triaxial pressure cell & hydrostatic pressure cell was designed and permeability experiments were performed with controlled axial and confining pressures. The measurement of permeability was conducted by increasing and decreasing effective stress. The permeability of non-bedding rock sample is the most sensitive to applied stress conditions and fracture permeability of tight sandstone increases with fracture treatment with proppant.
Surfactant-enhanced air sparging (SEAS) was developed to suppress the surface tension of groundwater prior to air sparging resulting in higher air saturation and larger contact area between NAPL and gas during air sparging. Larger contacting interface between NAPL and gas means faster mass transfer of contaminants from NAPL to gas phase. This new technique, however, is limited to relatively volatile contaminants because vaporization is its basic mechanism of mass transfer. In this study, SEAS was tested at an elevated temperature for a semi-volatile n-decane, which is expected not to be a good candidate of SEAS application due to its low vapor pressure at ambient temperature. Three sparging experiments were conducted using 1-dimensional column (5 cm id, 80 cm length) packed with sand; (1) ambient temperature ($23^{\circ}C$), column saturated with distilled water, (2) SEAS at ambient temperature ($23^{\circ}C$), for n-decane contaminated sand, (3) SEAS at elevated temperature ($73^{\circ}C$), for n-decane contaminated sand. Higher air saturation was achieved by SEAS compared to that by air sparging without surfactant application. The n-decane removal efficiency of SEAS at elevated temperature was significantly higher(> 10 times) than that of ambient SEAS. The n-decane concentrations in the gas effluent from column during SEAS at $73^{\circ}C$ are found to be 10 times of those measured at ambient temperature. Thus, SEAS technique can be applied for removal of semi-volatile contaminants provided that an appropriate technique for elevating aquifer temperature is available.
Proceedings of the Korean Vacuum Society Conference
/
1999.07a
/
pp.53-53
/
1999
전계방출을 이용한 평판 표시장치는 CRT가 가진 장점을 모두 갖는 동시에 얇고 가벼우며 낮은 전력소모로 완벽한 색을 구현할 수 있는 차세대 표시장치로서 이에 대한 여국가 활발히 이루어지고 있다. 여기에 사용되는 음극물질로서 실리콘이나 몰리 등을 팁모양으로 제작하여 사용해 왔다. 하지만 잔류가스에 의한 역스퍼터링이나 화학적 반응에 의해서 전계방출 성능이 점차 저하되는 등의 해결해야할 많은 문제가 있다. 이러한 문제들을 해결하기 위하여 탄소계 재료로서 다이아몬드, 다이아몬드상 카본 등을 이용하려는 노력이 진행되어 왔다. 이중 유리화 비정형 탄소는 다량의 결함을 가지고 있는 유리질의 고상 탄소 재로로서, 전기전도도가 우수하면서 outgassing이 적고 기계적 강도가 뛰어나며 고온에서도 화학적으로 안정하여 전계방출 소자의 음극재료로서 알맞은 것으로 생각된다. 유리화 비정형 탄소가루를 전기영동법으로 기판에 코팅하여 전계방출 소자를 제작하였다. 전기영동 용액으로 이소프로필알코올에 질산마그네슘과 소량의 증류수, 유리화 비정형 탄소분말을 섞어주었고 기판으로는 몰리(Mo)가 증착된 유리를 사용하였다. 균일한 증착을 위해서 증착후 역전압을 걸어 주는 방법과 증착 후 플라즈마 처리를 하는 등의 여러 가지 방법을 사용했다. 전계방출 전류는 1$\times$10-7Torr이사에서 측정하였다. 1회 제작된 용액으로 반복해서 증착한 횟수에 따라 표면의 거치기, 입자의 분포, 전계방출 측정 결과 등의 차이가 관찰되었다. 발광이미지는 전압에 따라 변화하였고, 균일한 발광을 관찰하기 위해서 오랜 시간동안 aging 과정을 거쳐야 했다. 그리고 구 모양의 양극을 사용해서 위치를 변화시키며 시동 전기장을 관찰하여 위치에 따른 전계방출의 차이를 조사하여 발광의 균일성을 알 수 있었다.on microscopy로 분석하였으며 구조 분석은 X-선 회절분석, X-ray photoelectron spectroscopy 그리고Auger electron spectroscope로 하였다. 증착된 산화바나듐 박막의 전기화학적 특성을 분석하기 위하여 리튬 메탈을 anode로 하고 EC:DMC=1:1, 1M LiPF6 액체 전해질을 사용한 Half-Cell를 구성하여 200회 이상의 정전류 충 방전 시험을 행하였다. Half-Cell test 결과 박막의 결정성과 표면상태에 따라 매우 다른 전지 특성을 나타내었다.도상승율을 갖는 경우가 다른 베이킹 시나리오 모델에 비해 효과적이라 생각되며 초대 필요 공급열량은 200kW 정도로 산출되었다. 실질적인 수치를 얻기 위해 보다 고차원 모델로의 해석이 필요하리라 생각된다. 끝으로 장기적인 관점에서 KSTAR 장치의 베이킹 계획도 살펴본다.습파라미터와 더불어, 본 연구에서 새롭게 제시된 주기분할층의 파라미터들이 모형의 학습성과를 높이기 위해 함께 고려된다. 한편, 이러한 학습과정에서 추가적으로 고려해야 할 파라미터 갯수가 증가함에 따라서, 본 모델의 학습성과가 local minimum에 빠지는 문제점이 발생될 수 있다. 즉, 웨이블릿분석과 인공신경망모형을 모두 전역적으로 최적화시켜야 하는 문제가 발생한다. 본 연구에서는 이 문제를 해결하기 위해서, 최근 local minimum의 가능성을 최소화하여 전역적인 학습성과를 높여 주는 인공지능기법으로서 유전자알고리즘기법을 본 연구이 통합모델에 반영하였다. 이에 대한 실증사례 분석결과는 일일 환율예측문제를 적용하였을 경우, 기존의 방법론보다 더 나운 예측성과를 타나내었다.pective" to workflow architectural discussions. The vocabulary suggested
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.89-89
/
2000
AlN 박막은 Al과 N원자의 부분적 이온결합 특성을 가진 공유결합을 한 육방정계의 wurtzite 경정구조의 화합물 반도체로서, III-V족 반도체 중 가장 큰 에너지 갭(6.2 eV), 결정 구조적 이방성, 화학 양론적 결합구조, 높은 탄성종과 전달속도(약 10$\times$106 m/s)와 높은 열전도도, 고온 안정성, 가시광성.적외선 영역에서의 좋은 투과성과 높은 굴절률, 상온 대기압에서의 유일하게 안정적인 특성을 가지고 있어, 절연재료, 내열재료, 저주파 영역 센서의 압전 트랜스듀서, 광전소자, 탄성파 소자 및 내환경 소자, MIS소자 등으로 주목받고 있다. 본 연구에서는 BAW 공진기의 활용을 목적으로 반응성 마그네트론 스퍼터링 방법으로 AIN 압전박막을 제작하여, 증착 조건-질소 농도, 고주파 출력, 전체 스퍼터링 압력, 기판 온도-에 대한 박막의 특성을 조사하였다. AlN 박막의 c축 우선 방위 결정성 및 낮은 투과성, 적당한 굴절률의 특성이 BAW 공진기의 활용을 위한 요건이므로, 각각의 증착 조건하에 제작된 박막은 XRD의 $\theta$/2$\theta$ 스캔 회절상에 의한 결정성의 분석과 우선 성장 결정면의 rocking curve 및 XRD로 측정한 FWHM과 표준 편차로 결정성의 배열성과 소자 응용가능성을 조사하였다. 박막의 표면.단면 미세 구조 및 평활도는 SEM으로 관찰하였으며, Al-N 결합 상태는 XPS와 FT-IR로 분석 조사하였다. 제작된 AlN 박막의 결정성 분석 결과, c축 우선 방위 성장을 위한 스퍼터링 압력에 대한 임계 질소 농도와 임계 스퍼터링 압력이 관찰되었다. 전체 스퍼터링 압력이 6~8 mTorr의 범위에서 나타난 최소 임계질소 농도는 10%, 최대 임계 질소 농도는 60%이며, 4 m Torr 이하 10 m Torr 이상의 전체 스퍼터링 압력에서 박막의 우선 방위성장이 제재된다. 이는 AlN 박막이 형성에 관여하는 질소 이온 양의 충분한 형성에 필요로 하는 질소 가스의 유입량에 따른 것으로 판단된다. AlN 박막의 c축 결정면인 (002) 결정면의 성장을 유도하며 다른 방향으로의 성장을 제어하여 소자 활용에 유용한 박막을 제작하기 위한 고주파 출력은 300W 정도가 적당하며, 기판을 가열하지 않았을 때 낮은 투과도를 나타낸다. 본 연구에 의한 BAW 공진기 활용을 위한 AlN 압전박막의 제작을 위한 최적 증착 조건은 기판의 가열 없이 6~8 mTorr의 전체 스퍼터링 압력에 20~25%의 질소종도, 300W의 고주파 출력이다. 최적 조건에서의 AlN 박막은 약 0.19$^{\circ}$의 FWHM과 약 0.08$^{\circ}$의 표준편차를 가지며, 균일하고 조밀한 표면 미세구조와 주상정 구조의 측면구조, 파장에 대한 약 2.0의 굴절률, 낮은 투과도와 화학 양론적 구조를 가지는 우수한 박막이 형성되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.