• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.15-22
• /
• 2002

As the emission regulations on the automobiles have been increasingly stringent, precise control of air/fuel ration is one of the most important issues on the gasoline engines. Although many researches have been carried out to identify the fuel transport phenomena in the port fuel injection gasolines, mixture preparation in the cylinder has not been fully understood due to the complexity of fuel film behavior, In this paper, the mixture preparation during cold engine start is studied by using a Fast Response Flame ionization Detector.(FRFID) In order to estimate the transportation of injected fuel from the intake port into cylinder, the wall wetting fuel model was used. The two coefficient($\alpha$,$\beta$) of the wall-wetting fuel model was determined from the measured fuel mass that was inducted into the cylinder at the first cycle after injection cut-in. $\alpha$( ratio of directly inducted fuel mass into cylinder from injected fuel mass) and $\beta$ (ratio of indirectly inducted fuel mass into cylinder from wall wetted fuel film on the wall) was increased with increasing cooling water temperature. To reduce a air/fuel ratio fluctuation during cold engine start, the appropriate fuel injection rate was obtained from the wall wetting fuel model. Result of air/fuel ratio control, air/fuel excursion was reduced.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.157-164
• /
• 2014

Dual fuel combustion strategy with di-methl ether (DME) and gasoline was tested in a compression ignition engine. Characteristics of combustion and emissions were analyzed with the variation of engine operating parameters such as fuel proportion, DME injection timing, intake oxygen concentration, DME injection pressure and so forth. Gasoline was injected into the intake manifold to form the homogeneous mixture with intake charge and DME was injected directly into the cylinder at the late compression stroke to ignite the homogeneous gasoline-air mixture. Dual fuel combustion strategy was advantageous in achievement of higher thermal efficiency and low NOx emission compared with DME single fuel combustion. Higher thermal efficiency was attributed to the lower heat tranfer loss from the decreased combustion temperature since the amount of lean premixed combustion was increased with the larger amount of gasoline proportion. Lower NOx emissions were also possible by lowering the combustion temperature.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.151-158
• /
• 2008

Gasoline Homogeneous Charge Compression Ignition (HCCI) combustion is a new combustion concept. Unlike the conventional internal combustion engine, the premixed fuel mixture with high residual gas rate is auto-ignited and burned without flame propagation. There are several operating factors which affect HCCI combustion such as start of combustion (SOC), residual gas fraction, engine rpm, etc. Among these factors SOC is a critical factor in the combustion because it affects exhaust gas emissions, engine power, fuel economy and combustion characteristics. Therefore SOC of gasoline HCCI should be controlled precisely, and SOC detection should be preceded SOC control. This paper presents a control oriented SOC detection method using 50 percent normalized difference pressure. Normalized difference pressure is defined as the normalized value of difference pressure and difference pressure is difference between the in-cylinder firing pressure and the motoring pressure. These methods were verified through the HCCI combustion experiments. The SOC detection method using difference pressure provides a fast and precise SOC detection.

• Journal of ILASS-Korea
• /
• v.17 no.2
• /
• pp.71-76
• /
• 2012

The aim of this work was to investigate the combustion and nanoparticle emission characteristics of premixed charge compression ignition (PCCI) combustion at various test conditions using a single cylinder common-rail diesel engine. In order to create the homogeneity of fuel-air mixture, the premixed fuel (gasoline) was injected into premixing chamber during the intake process and then the diesel fuel was directly injected into the combustion chamber as an ignition source for the gasoline premixture. From these results, it revealed that the ignition delays and combustion durations were gradually prolonged and the peak combustion pressure were increased because diesel fuel was injected early injection timing with the increase of premixed ratio. In addition, as the increase of premixed ratio, total particle number is generally decreased and particle volume also indicated low levels at the direct injection timing from BTDC $20^{\circ}$ to TDC. At further advanced injection timing, total particle number and volume were generally increased

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.868-875
• /
• 2001

The objective of this study is to investigate the average droplet size distributions of a GDI spray by simultaneous fluorescence/scattering image technique. GDI engine is recently very popular because of high engine efficiency and low emissions. However, the injectors must have good spray characteristics because the fuel is directly injected into the cylinder. The fuel mixtures used in this study were 2% of fluorobenzene, 9% of DEMA(diethyl-methyl-amine) and 89% of hexane by volume. The system for obtaining 2-D fluorescence/scattering images of fuel spray was constituted of a laser sheet, a doubling prism, optical filters, and an ICCD camera. Using the ratio of the fluorescence to the scattering intensities, SMD distributions were obtained. SMD measured by the technique was compared with that obtained by PDA. It was found that average droplet size was bigger at spray center in the early stage of injection and at the outer periphery of the spray in the late stage of injection.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.884-890
• /
• 2008

Many researches have been carried out to reduce the emission levels and lower the fuel consumption in SI engines. Recently electronically controlled injection system is widely adapted to a passenger car to achieve these goals. Throttle body is also an important factor which influences on the emissions and engine power. In this study we redesigned a throttle body and conducted an experimental study to see the effects on engine performance and emission characteristics. We could find that idle speed control(ISC) showed stable operation characteristics as the cooling water temperature varied. And CO and HC emissions also satisfied the regulation limit.

• Journal of ILASS-Korea
• /
• v.11 no.1
• /
• pp.17-23
• /
• 2006

The influence of fuel spray characteristics on engine performance has been known as one of the major concerns to Improve fuel economy and to reduce exhaust emissions. In general, the UBHC(Unburned Hydrocarbon) emission could be reduced by decreasing the droplet size of the fuel sprays. In PFI (Port Fuel Injection) gasoline engines, the mixture of air and fuel would not be uniform under a certain condition, because the breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve sheat. In this study, were investigated the transient spray characteristics and dynamic behavior of droplets from 2holes-2sprays and 4holes-2sprays type injectors used in PFI gasoline engine. Mean droplet size and optical concentration were measured by LDPA (Laser Diffraction Particle size Analyzer). The variation of droplet mean diameter and optical concentration were measured for understanding the behavior of unsteady spray.

• Journal of ILASS-Korea
• /
• v.2 no.4
• /
• pp.15-21
• /
• 1997

In a gasoline engine with port injection system, the fuel behavior in the intake port has significant influence on the HC emission and the precise A/F control. That is to say, it is inevitable that the injection direction and behavior of fuel injected in the intake port have an effect on the generation of unburned HC within a cylinder. In this paper, we visualized fuel behavior in the intake port using micro CCD camera synchronized with the stroboscope and investigated the fuel-film characteristics formed at the wall of intake port by processing image captured with VCR in the transparent intake port made of acryl. Using these measuring methods, it was found that fuel behavior and the formation of fuel-film in the intake port could be evaluated qualitatively. And results obtained by these methods show that 2-spray injector minimizes the fuel-film formed in the intake port of a DOHC gasoline engine.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.334-342
• /
• 2009

Trends in the automotive market require the application of new engine technologies, which allows for the use of different types of fuel. Since ethanol is a renewable source of energy and has lower $CO_2$ emissions than gasoline, ethanol produced from biomass is expected to be used more frequently as an alternative fuel. It is recognized that for spark ignition (SI) engines, ethanol has the advantages of high octane number and high combustion speed. Due to the disadvantages of ethanol, it may cause extra wear and corrosion of electric fuel pumps. On-board hydrogen production out of ethanol is an alternative plan. This paper investigates the influence of ethanol fuel on SI engine performance, thermal efficiency and emissions. The combustion characteristics with hydrogen-enriched gaseous fuel from ethanol are also examined. As a result, thermal efficiency increase compared to gasoline. Also, reductions in $CO_2$, NOx, and THC combustion products for ethanol vs. gasoline are described.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.87-92
• /
• 2005

An altitude control using a fuzzy controller was performed for a series of research for autonomous flight control of industrial unmanned helicopters. The 3m class gasoline engined unmanned helicopter was designed, and using the designed specifications, Takagi-Sugeno-Kang type fuzzy controller was designed. The input membership functions were generated using target altitude, altitude error and velocity of unmanned helicopter. With these membership functions, the control inputs for altitude control were calculated. These control input signal can control the main rotor's pitch and determine the velocity and altitude of the unmanned helicopter. Also, the altitude control performance of the designed fuzzy controller was evaluated by computer simulations