• Journal of ILASS-Korea
• /
• 제4권2호
• /
• pp.33-39
• /
• 1999

This paper presents the spray atomization characteristics of the high-pressure gasoline injector for the direct-injection gasoline engine. The gasoline sprays of the injector were minted into a pressurized spray chamber with a optical access at various ambient pressures. The atomization characteristics of fuel spray such as mean diameter, mean velocity of droplet were measured by the phase Doppler particle analyzer system. In order to investigate the effect of fuel injection pressure on the quantitative characteristics of spray, the global visualization and experiment of particle measurement in the fuel spray were investigated at 3, 5 and 7 MPa of injection pressure under different ambient pressure in the spray chamber. Based on the results of this work, the fuel injection pressure of fuel injector in gasoline direct-injection engine have influence upon distribution of the mean velocity and droplet size of fuel spray. Also, the influence of injection pressure on the velocity distribution at various measuring location were investigated.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권1호
• /
• pp.115-123
• /
• 2001

This study describes the combustion characteristics under various condition of air excess ratio and ignition timing in a 2-valve gasoline optically accessible engine with swirl control valve(SCV). It adapted three different types of SCA(open ration 72.5%, 78%, 89%) to strengthen a swirl flow. Pressure data were acquired using pressure sensor to investigate the effect of swirl flow on combustion, and from these pressure data, IMEP(indicated mean effective pressure) and MFB(mass fraction burnt)were calculated to explain burn rate and flame speed. From acquired flame images, inspected the flame propagation direction, flame area, and flame centroid, Flame propagation direction was shown different tendency between with/without SCV, and flame area with SCV was faster and larger than that of conventional engine. Finally, the representative flame image at each crank angle were acquired by PDF method to verify flame growth process. It is found that strengthened swirl flow is more beneficial for faster and stable combustion.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제4권5호
• /
• pp.197-205
• /
• 1996

The flow characteristics of five different 4-valve cylinder heads were investigated in a steady flow rig using laser-Doppler velocimetry. The tumble flow of each head with pentroof combustion chamber was quantified by nondimensional tumble number using a tumble adaptor. The formation of tumbling vortex was examined in an optical single-cylinder engine which has windows for in-cylinder LDV measurements. Tumble vortex ratio was estimated from the tumble flow measurement. The four-valve cylinder heads with pent-roof combustion chamber showed the tumble vortex from the intake process, which was investigated in the steady flow test. The tumble adaptor which converts the tumble into swirl flow was found to be feasible in predicting the tumble flow in the real engine. The tumble strength in the steady flow test coincides with that in the real engine experiment within 15%. It was found that the steady flow test on the four-valve cylinder heads provides the tip for a better design of cylinder head.

• Journal of the korean Society of Automotive Engineers
• /
• 제7권4호
• /
• pp.49-56
• /
• 1985

This study consists of instrumenting and running tests on variable compression engines and measuring the following combustion characterics: (a)flame speed, (b) emission and (c)performance parameter such as power and economy. The results were as follows: 1) The phase separation diagram of substitute fuels were obtained from phase separation experiment. 2) The flame propagation speed of substitute fuels were higher than gasoline and increased with increasing methanol weight percent of substitute fuels. 3) BEMP of substitute fuels was slightly less than that of gasoline but in the range of small weight percent, BEMP was compatible to gasoline. 4) Concentration of NOx decreased significantly with delaying spark advancing time. Also, it decreased for rich equivalence ratio but increased with high compression ratio. In general, NOx concentration was much lower than that of gasoline. 5) Concentration of HC and CO increased for rich equivalence ratio. Also it was lower than that of gasoline.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제5권5호
• /
• pp.97-103
• /
• 1997

Effects of fuel injection timing on the lean misfire limit of a sequential MPI SI engine has been investigated. To investigate the interaction of injection timing and intake flow characteristics, so called axial stratification phenomena, 4 kinds of different intake swirl port of the same combustion chamber geometry have been teated in a single cylinder engine test bench. And 2 kinds of fuel, gasoline and compressed natural gas(CNG), were used to see the effect of liquid fuel vaporization. Result shows that combination of port swirl and injection timing governs the lean misfire limit and lean misfire limit envelopes remain almost the same for a given ratio regardless of engine speed. It is also found that two phase flow has some effects on lean misfire limit.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제9권5호
• /
• pp.62-74
• /
• 2001

In this study, the prediction of performances and emissions of the gasoline engine of a light passenger car has been accomplished. The method of characteristics including friction, heat transfer, area change and entropy gradients was used to analyze the flow in the intake and exhaust systems. For in-cylinder calculation, the single-zone model was adopted for the periods of the intake, exhaust, compression and the expansion of the burnt gas and the 2-zone expansion model was applied to the period of combustion process. The simulation program was verified by comparison with the experimental values both for the naturally aspirated engine and the turbocharged engine showing good agreements. Using the simulation program, multi-valve system and turbocharging were examined as a means of increasing engine Performances.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제6권2호
• /
• pp.32-42
• /
• 1998

Lean burn gasoline engine is recognized as a promising way to meet better fuel economy. Lean burn engine is classified into port injection and direct injection(DI), DI is more active technique for improving fuel economy with ultra-lean operation, Nowadays, port injected lean burn engine has been produced by many Japan maker. Also, DI engine is also possible for production owing to improvement in control technique of spray, flow air fuel ratio. DI engine uses either homogeneous stoichiometric mixture or stratified mixture by controlling injection timing to be early or late respectively. HM(homogeneous mixture) is worse than SM(stratified mixture) in view of ultra-lean operation in partical load and Nox reducion by using EGR control. But, HM has advanteges in cold starting and emission reduction during transient operation, This paper describes experimental variables and bench test results of HM GDI engine.

• Tribology and Lubricants
• /
• 제9권2호
• /
• pp.36-48
• /
• 1993

This study is concerned with the changes (deterioration) of the mechanical properties of used oil in the gasoline engine. The analysed properties of used oil were friction, antiwear, wear debris, load-carrying ability and the formation of surface film. From this study, it was found that the oil used in engine was deteriorated to increase the wear and fricion and decrease the load-carrying ability as the running distance of oil was increased. Also the main cause of deterioration was related to the formation of the protective film on the contact zone. When the film was composed with rich additives (sulfur), this could properly protect contact zone from the increase of wear and friction. But as oil was deteriorated, it could not form such a film and therefore the protective ability of sliding surface diminished.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.914-915
• /
• 2011

최근 지구온난화의 문제점으로 저 탄소 친환경 자동차로 배터리 전력과 가솔린 엔진을 같이 사용하는 하이브리드 자동차가 주목 받고 있다. 최근에 개발되고 있는 하이브리드 자동차는 전력의 효율적인 사용을 위해 배터리의 전압이 증가되고 있고 이에 따라 DC High Voltage를 다룰 수 있는 Relay의 용량이 요구된다. 이런 측면에서 하이브리드 자동차에 사용되는 EV-Relay의 경우 소형화에 따른 문제점이 발생한다. 그 대표적인 문제점으로 EV-Relay의 접점에 일시적인 과전류가 흐르면서 전기적 반발력이 발생하여 EV-Relay의 폭발과 같은 위험한 문제점이 발생 할 수 있다. 이에 따라 본 논문에서는 Relay에서 발생하는 전기반발력의 힘을 MAXWELL프로그램을 통해 모의하는 연구를 하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제11권3호
• /
• pp.20-27
• /
• 2003

In this paper, the fuel transport characteristics during transient condition was studied by using a Fast Response Flame Ionization Detector(FRFID). The quantitative measurement method for the inducted fuel mass into cylinder is studied. The inducted fuel mass into the cylinder was estimated by using calculated air-fuel ratio by hydrocarbon concentration of cylinder and air flow model. In order to estimate the transportation of injected fuel from the intake port into cylinder, the wall wetting fuel model was used. The two coefficient $\alpha$,$\beta$) of the wall-wetting fuel model was determined from the measured fuel mass that was inducted into the cylinder at the first cycle after injection cut-off To reduce an air/fuel ratio fluctuation during rapid throttle opening, the appropriate fuel injection rate was obtain from the wall wetting model with empirical coefficients. Result of air/fuel ratio control, air/fuel excursion was reduced.