• Tunnel and Underground Space
• /
• v.29 no.2
• /
• pp.124-134
• /
• 2019

Subcritical crack growth in rock material can occur under monotonic and cyclic loading. Subcritical crack growth plays an important role in evaluating the long-term stability of structures in rocks. This paper presents the results of studies conducted to determine subcritical crack growth parameters under monotonic and cyclic loading in rock-like material. The constant stress rate method was employed for monotonic loading. The subcritical crack growth parameter of n under cyclic loading was determined by the relation between the rate of crack growth per cycle and stress intensity factor range. The specimens contained pre-existing flaws with 45 and 60 degrees of inclination angle and flaws spacing and continuity were varied to arrange crack growth in shear or tensile manner. The results show that the parameter of n is almost constant regardless of the applied load conditions such as monotonic and cyclic or shear and tension.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.415-422
• /
• 2001

The present paper focuses on the development of a realistic analysis model for the deformation calculation of reinforced concrete beams subjected to fatigue loadings. The proposed model considers the effect of cyclic creep, which arises from the repeated loading, to calculate the deformation of reinforced concrete beams. A comprehensive experimental program has been set up to identify the deformation accumulation of reinforced concrete beams under repeated loadings. The major test variables were the concrete compressive strength and the magnitude of fatigue loads. The model was calibrated from the present test results. The proposed model allows more realistic analysis of reinforced concrete beams under fatigue loads, especially deformation accumulation of such beams.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1193-1199
• /
• 1990

Effects of strain hardening exponents on the behavior of fatigue crack propagation are experimentally investigated. The retardation effect of fatigue crack propagation after single overloading is investigated in relation to strain hardening exponent and crack closure. A relationship between crack opening ratio and strain hardening exponents is inspected through an examination of the crack closure behavior. An empirical equation relating retardation effect of fatigue crack propagation after single overloading, percent peak load and strain hardening exponent of materials is proposed.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.2
• /
• pp.41-48
• /
• 1989

This paper investigates the relationship between strain hardening exponents(n) of various marine materials and fatigue crack retardation effect after applying single overload. Using the four different sheet materials, following results are obtained. (1) The fatigue crack propagation rate after applying single overload was retarded and the effects of this retardation were closely related to the strain hardening exponent. (2) The larger the strain hardening exponents were, the more were the fatigue crack retardation effects after applying single overload. (3) The considerable crack closure with the applying of a overload was observed in matrals with large strain hardening exponent. When n is smaller than 0.1, the fatigue crack retardation effects are negligible. On the contrary, when n is larger than 0.2 the fatigue crack retardation effects are significant.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.167-174
• /
• 2009

The simulation of dynamic load was conducted based on surface profile on asphalt concrete pavement, vehicle speeds, and suspension types using a truck simulation program. The results of the simulated dynamic load based on different surface profile, vehicle speeds, and suspension types are analyzed. As pavement roughness and vehicle speed are increased, the dynamic load was increased. Walking beam suspension produces greater dynamic load than air spring suspension. Pavement damage index is calculated based on covariance of dynamic load and Paris-Erdogan fracture parameter, n which is based on creep compliance tests of asphalt mixtures used in Korea. The higher covariance of dynamic load, confidence level, and fracture parameter are used, the greater pavement damage index is obtained. Specification of pavement roughness can be developed in various vehicle speeds and asphalt mixtures, and pay factor can be determined after constructing asphalt concrete pavement using pavement damage concepts.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.645-645
• /
• 1989

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.167-175
• /
• 1988

The principle objective of this study is to evaluate the fatigue behavior of structural steel components of highway bridges subjected to service stresses. The main aspects of this investigation are; 1) a measurement and statistical analysis of service stress cycles observed in highway bridge. 2) fatigue tests under equivalent constant-amplitude(CA) loading and simulated variable-amplitude(VA) loading 3) a evaluation of the fatigue behavior under VA-loading by eqivalent root mean cube (RMC) stress range. Theoretically, the RMC model is adequate in evaluation of fatigue behavior under VA-loading, because the regression coefficient (m) of crack growth rate is 3 approximately. The result of fatigue test shows that the RMC model is fitter than the current RMS model in fatigue evaluation under VA-loading. The interaction effects and sequence effects under VA-loading affect little fatigue life of structural components. As the transition rate of stress ranges is higher, the crack growth rate is higher.

• Composites Research
• /
• v.12 no.2
• /
• pp.53-61
• /
• 1999

A failure criterion must be considered in each failure mode and loading condition to provide easy determining strength parameters, flexibility and rational simplicity. In this study, new failure criterion was developed by introducing equivalent strength under biaxial loading of tension and torsion. The experimental results showed that the equivalent biaxial strength has a power law relation with respect to a parameter, cos($tan^{-1}R_b$). Failure strength under biaxial loadings could be predicted as a function of tensile strength, torsional strength and biaxial ratio. The scattering of experimental data could be predicted using a Weibull distribution function and the concept of equivalent biaxial strength. Also, in this study, a fatigue theory was developed based on a plane stress model which enabled the S-N curve for combined stress states to be predicted from the S-N data for uniaxial loading. The prediction models can be predicted a biaxial strength and fatigue life of general laminated composite naterials under multi-axial loadings.

• Journal of Korean Society of Forest Science
• /
• v.86 no.1
• /
• pp.17-24
• /
• 1997

As the first step to estimate the potential natural vegetation distribution of the globe, the best spherical interpolation method was developed to the temperature and precipitation which have close relation to the distribution pattern of world natural vegetation. For developing the interpolation method, a named Light Climatic Dataset composed of 1,060 stations around the globe was randomly divided into halves of feeding side and target side. The discrepancy between the observed and estimated values at the target stations was compared with combinations of parameters and methods. The estimated values were calculated to each combination which is all-out, constant radius and constant station methods in the selection of the feeding stations, n square reciprocal and negative exponential functions in weighting function of distance between feeding stations and each target, and oval weighting in direction of the feeding stations from each target. As a result, it turned out that the spherical interpolation with negative exponential weighting function fed from the constant radius stations ovally weighed yields the best estimates both for temperature and for precipitation. The parameters for temperature are $30^{\circ}$ in constant radius, 0.78 in negative exponential function and 0.4 in oval weighting, and for precipitation are $30^{\circ}$, 0.53 and 0.4, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.261-271
• /
• 2003

A condition evaluation procedure for the pavement foundations using multi-load level Falling Weight Deflectometer(FWD) deflections is presented in this paper. A dynamic finite element program incorporating a stress-dependent material model, was used to generate the synthetic deflection database. Based on this synthetic database, the relationships between surface deflections and critical responses, such as stresses and strains in base and subgrade layers, have been established. FWD deflection data, Dynamic Cone Penetrometer(UP) data, and repeated load resilient modulus testing results used in developing this procedure were collected from the Long Term Pavement Performance (LTPP) and North Carolina Department of Transportation (NCDOT) database. Research effort focused on investigation of the effect of the FWD load level on the condition evaluation procedures. The results indicate that the proposed procedure can estimate the pavement foundation conditions. It is also found that structurally adjusted Base Damage Index (BDI) and Base Curvature Index (BCI) are good indicators for the prediction of stiffness characteristics of aggregate base and subgrade respectively. A FWD test with a load of 66.7 kN or less does not improve the accuracy of this procedure. Results from the study for the nonlinear behavior of a pavement foundations indicate that the deflection ratio obtained from multi-load level deflections can predict the type and quality of the pavement foundation materials.