• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.243-251
• /
• 1994

ITO(Indium Tin Oxide) film with thickness of 1500.angs. was prepared by an e-beam evaporator onto a glass and a p-type InP wafer (100) LEC grown Zn-doped p=2.3*10$\^$16/cm$\^$-3/), in which the components of ITO used for evaporation source were hot pressed pellets 1 mole% ln$\_$2/O$\_$3/+9 mole% SnO$\_$2/, and evaporated in O$\_$2/ ambient. The optimum conditions to preparation of ITO thin film were the substrate temperature of 350.deg. C, the injected oxygen pressure of 2*10$\^$-4/ torr, and the evaporation speed of 0.2-0.3.angs./sec, respectively. In these optimum conditions, the resistivity and the carrier concentration were 5.3*10$\^$-3/ .ohm.-cm, 6.5*10$\^$20/cm$\^$-3/, and the transmittance was over 80%. From the results of J-V measurements in ITO/p-InP structure solar cells, the higher pressure of injected oxygen, the more open circuit voltage. The efficiency of ITO/p-InP solar cell without the grid line contact, prepared by the optimum evaporation conditions, was 7.19%. By using the grid line contact, the efficiency, the open circuit voltage, the short circuit current density, the fill factor, the series resistance, and the shunt resistance were 8.5%, 0.47V, 29.48 mAcm$\^$-2/ , 61.35%, 3.ohm., and 26.6k.ohm., respectively.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.5
• /
• pp.239-243
• /
• 2014

The electrical and optical properties of amorphous In-Tin-Zinc-Oxide(ITZO) deposited at room temperature using rf-magnetron sputtering were investigated. The amorphous ITZO thin films were obtained at the composition of In:Sn:Zn = 6:2:2, 4:3:3, and 2:4:4, but the ITZO (8:1:1) showed a crystalline phase of bixbyite structure of In2O3. The resistivity of ITZO could be controlled by oxygen pressure in the sputtering ambient. The resistivity of post-annealed ITZO thin films exhibited the dependence on the amount of Indium. Optical energy band gap and transmittance increased as the amount of indium in ITZO increased. For the device application with ITZO, the bottom-gated thin-film transistor using ITZO as a active channel layer was fabricated. It showed a threshold voltage of 1.42V and an on/off ratio of $5.63{\times}10^7$ operated with saturation field-effect mobility of $14.2cm^2/V{\cdot}s$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.54.1-54.1
• /
• 2010

산화물 기반의 TFT는 유리, 금속, 플라스틱 등 기판 종류에 상관없이 균일한 제작이 가능하며, 상온 및 저온에서 대면적으로 제작이 가능하고, 저렴한 비용으로 제작 가능하다는 장점 때문에 최근 많은 연구가 이루어지고 있다. 현재 TFT 물질로 많이 연구되고 있는 산화물은 ZnO (3.4 eV)나 InOx (3.6 eV), GaOx (4.9 eV), SnOx(3.7 eV)등의 물질과 각각의 조합으로 구성된 재료들이 주로 사용되고 있으며, 가장 많은 연구가 이루어진 ZnO 기반의 TFT는 mobility와 switching 속도에서 우수한 특성을 보이나, 트렌지스터의 안정성이 떨어지는 것으로 보고 되고 있다. 그러나 IGZO 물질의 경우 결정학적으로 비정질이며 상온 및 저온에서 대면적으로 제작이 가능하고, 높은 전자 이동도의 특성을 가지고 있는 장점 때문에 최근 차세대 산화물 트렌지스터로 각광받고 있다. IGZO TFT 소자의 경우 Ag, Au, In, Pt, Ti, ITO 등 다양한 전극 물질이 사용되고 있는데, 이들 중 active channel과 ohmic contact을 이루는 Al, Ti, Ag의 적용을 통해 향상된 성능을 얻을 수 있다. 하지만 이들 전극 재료는 TFT 소자 제작시 필수적인 열처리 공정에 노출되면서 active channel 과 전극 사이 계면에 문제점을 야기할 수 있다. 특히, Ti의 경우 산화가 잘되기 때문에 전극계면에 TiO2를 형성하여 contact resistance의 큰 영향을 미치는 것으로 보고 되고 있다. 본 연구에서는 ohmic 전극재료인 Ti 또는 Ti/Au를 적용하여 TFT 소자 제작 및 특성에 대한 평가를 진행했으며, 열처리에 따른 전극과 IGZO 계면 사이의 미세구조와 전기적인 특성간의 상관관계를 연구하였다. 이를 통해, 소자 제작 공정을 최적화하고 신뢰성 있는 소자 특성을 얻을 수 있었다.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.734-740
• /
• 2016

The micron-sized indium zinc tin oxide (IZTO) particles were prepared by spray pyrolysis from aqueous precursor solution for indium, zinc, and tin and organic additives such as citric acid (CA) and ethylene glycol (EG) were added to aqueous precursor solution for indium, zinc, and tin. The obtained IZTO particles prepared by spray pyrolysis from the aqueous solution without organic additives had spherical and filled morphologies, whereas the IZTO particles obtained with organic additives had more hollow and porous morphologies. The micron-sized IZTO particles with organic additives were changed fully to nano-sized IZTO particles, whereas the micron-sized IZTO particles without organic additives were not changed fully to nano-sized IZTO particle after post-treatment at $700^{\circ}C$ for 2 hours and wet-ball milling for 24 hours. Surface resistances of micron-sized IZTO's before post-heat treatment and wet-ball milling were much higher than those of nano-sized IZTO's after post-heat treatment and wet-ball milling. From IZTO with composition of 80 wt. % $In_2O_3$, 10 wt. % ZnO, and 10 wt. % $SnO_2$ which showed a smallest surface resistance IZTO after post-heat treatment and wet-ball milling, thin films were deposited on glass substrates by pulsed DC magnetron sputtering, and the electrical and optical properties were investigated.