• 한국분말재료학회지
• /
• 제25권1호
• /
• pp.1-6
• /
• 2018

Uniform $TiO_2$ blocking layers (BLs) are fabricated using ultrasonic spray pyrolysis deposition (USPD) method. To improve the photovoltaic performance of dye-sensitized solar cells (DSSCs), the BL thickness is controlled by using USPD times of 0, 20, 60, and 100 min, creating $TiO_2$ BLs of 0, 40, 70, and 100 nm, respectively, in average thickness on fluorine-doped tin oxide (FTO) glass. Compared to the other samples, the DSSC containing the uniform $TiO_2$ BL of 70 nm in thickness shows a superior power conversion efficiency of $7.58{\pm}0.20%$ because of the suppression of electron recombination by the effect of the optimized thickness. The performance improvement is mainly attributed to the increased open-circuit voltage ($0.77{\pm}0.02V$) achieved by the increased Fermi energy levels of the working electrodes and the improved short-circuit current density ($15.67{\pm}0.43mA/cm^2$) by efficient electron transfer pathways. Therefore, optimized $TiO_2$ BLs fabricated by USPD may allow performance improvements in DSSCs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1223-1225
• /
• 1994

The properties of $TiN/TiSi_2$ bilayer formed by a rapid thermal anneal ing is investigated when thin $SiO_2$ film exists at the Ti-Si interface. The competitive reaction for the $TiN/TiSi_2$ bilayer occurs above $600^{\circ}C$. The thickness of the $TiSi_2$ layer decreases with increasing $SiO_2$ film thickness while the TiN layer increases at the competitive reaction. The composition of TiN layer is changed to the $TiN_xO_y$ film due to the thin $SiO_2$ layer at the Ti-Si interface while the structure of the TiN and $TiSi_2$ layers was not changed.

• 태양에너지
• /
• 제9권1호
• /
• pp.14-21
• /
• 1989

Preparation of $TiO_2$ Film by the Dip-coating Method and its Application to photo-electrochemical Electrodes. $TiO_2$ film of n-type semiconductor has been of great interest as a material for solar energy conversion. For its practical application, the dip-coating method has been applied to prepare $TiO_2$ (anatase) film on the nesa glass substrate. Films up to about $1.8{\mu}m$ in thickness can be obtained by repeating the operation, dipping $\to$ pulling up $\to$ drying $\to$ heating at $500^{\circ}C$ for 10 minute. Heating temperature at $500^{\circ}C$ was adopted to convert $TiO_2$ gels into $TiO_2$ crystalline films. The $TiO_2$ films showed the maximum photocurrent ($14mA/cm^2$) at the film thickness of about $1.8{\mu}m$. It was also found that the additional heating at $500^{\circ}C$ for about 20 minutes improved remarkably the photo current of the $TiO_2$ films.

• 한국분말재료학회지
• /
• 제17권3호
• /
• pp.216-222
• /
• 2010

Self-standing $TiO_2$ nanotube arrays were fabricated by potentiostatic anodic oxidation method using pure Ti foil as a working electrode and ethylene glycol solution as electrolytes with small addition of $NH_4F$ and $H_2O$. The influences of anodization temperature and time on the morphology and formation of $TiO_2$ nanotube arrays were investigated. The fabricated $TiO_2$ nanotube arrays were applied as a photoelectrode to dye-sensitized solar cells. Regardless of anodizing temperature and time, the average diameter and wall thickness of $TiO_2$ nanotube show a similar value, whereas the thickness show a different trend with reaction temperature. The thickness of $TiO_2$ nanotube arrays anodized at $20^{\circ}C$ and $30^{\circ}C$ was time-dependent, but on the other hand its at $10^{\circ}C$ are independent of anodization time. The conversion efficiency is low, which is due to a morphology breaking of the $TiO_2$ nanotube arrays in manufacturing process of photoelectrode.

• 한국재료학회지
• /
• 제17권10호
• /
• pp.548-554
• /
• 2007

[ $BaTiO_3$ ] thick film by an interfacial polymerization method was prepared at the liquid/liquid interface between benzyl alcohol saturated solution with the basic catalyst [diethyl amine ($NHEt_2$) or triethylamine ($NEt_3$)], and the water dissolved with $TiO_2$ and $Ba(CH_3COO)_2$. The film thickness increased gradually with an increase in diethyl amine($NHEt_2$) or triethylamine($NEt_3$) volume and the reaction time. The homogeneity of $BaTiO_3$ thick film after sintered at $600^{\circ}C$ was confirmed by EPMA analysis, which showed that both of Ba and Ti element were homogeneously distributed on the surface as well as in the perpendicular direction of the film. The thickness of $BaTiO_3$ film obtained by this process was $8.75\;{\mu}m$.

• Bulletin of the Korean Chemical Society
• /
• 제23권5호
• /
• pp.741-744
• /
• 2002

Single phase of multicomponent oxide ZrTiO4 film could be prepared through surface sol-gel route simply by coating the mixture of 100 mM zirconium butoxide and titanium butoxide on $Pt/Ti/SiO_2Si(100)$ substrate, following pyro lysis at $450^{\circ}C$, and annealing it at 770 $^{\circ}C.$ The dielectric constant of the film was reduced as the film thickness decreased due to of the interfacial effects caused by layer/electrode and a few voids inside the multilayer. However, the dielectric property was independent of applied dc bias sweeps voltage (-2 to +2 V).The dielectric constant of bulk film, 31.9, estimated using series-connected capacitor model was independent of film thickness and frequency in the measurement range, but theoretical interfacial thickness, ti, was dependent on the frequency. It reached a saturated ti value, $6.9{\AA}$, at high frequency by extraction of some capacitance component formed at low frequency range. The dielectric constant of bulk ZrTiO4 pellet-shaped material was 33.7 and very stable with frequency promising as good applicable devices.

• 태양에너지
• /
• 제10권2호
• /
• pp.69-76
• /
• 1990

[ $TiO_2$ ] 박막을 물에 담그고 빛을 조사하였을때의 물의 광전기화학적 분해현상을 관찰하였다. $TiO_2$ 박막은 스프레이법에 의해 $SnO_2$ 네사글라스를 만들고 이 네사글라스 위에 딥-코오팅법을 이용하여 $TiO_2$ 박막을 코오팅하였다. 다양한 두께의 $TiO_2$ 박막의 I-V 특성을 조사하였고 SEM에 의해 그 표면 상태를 알아 보았다. 필름의 두께가 $1.8{\mu}m$ 일때 광전기 전류가 최대로 나타남을 볼 수 있었다. $TiO_2$ 박막을 산성 수용액(pH=1)에 담그고 Xe-램프를 광원으로 하여 광전기 화학반응에 의한 물의 광 분해에 의해 산소 및 수소 가스가 발생함을 볼 수 있었다.

• 한국분말재료학회지
• /
• 제29권3호
• /
• pp.207-212
• /
• 2022

Nanosized rutile titanium dioxide (TiO₂) is used in inorganic pigments and cosmetics because of its high whiteness and duality. The high quality of the white pigments depends on their surface coating technique via the solgel process. SiO₂ coatings are required to improve the dispersibility, UV-blocking, and whiteness of TiO₂. Tetraethyl orthosilicate (TEOS) is an important coating precursor owing to its ability to control various thicknesses and densities. In addition, we use Na₂SiO₃ (sodium silicate) as a precursor because of its low cost. Compared to TEOS, which controls the pH using a basic catalyst, Na₂SiO₃ controls the pH using an acid catalyst, giving a uniform coating. The coating thickness of TiO₂ is controlled using a surface modifier, cetrimonium bromide, which is used in various applications. The shape and thickness of the nanosized coating layer on TiO₂ are analyzed using transmission electron microscopy, and the SiO₂ nanoparticle behavior in terms of the before-and-after size distribution is measured using a particle size analyzer. The color measurements of the SiO₂ pigment are performed using UV-visible spectroscopy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1379-1381
• /
• 1998

Powder electroluminescent device (PELD) structured conventionally dielectric and phosphor layer, between electrode and their layer fabricated by screen printing splaying or spin coating method. To promote performance of PELDs, we approached the experiments for different structure and thickness variation of PELD. Thickness variation($30{\mu}m{\sim}130{\mu}m$) was taken. To investigate electrical and optical properties of PELDs, EL spectrum, transferred charge density using Sawyer-Tower's circuit brightness was measured. Variation of structure in PELDs was as follows: WK-1 (ITO/BaTiO3/ZnS:Cu/Silver paste), WK-2 (ITO/BaTiO3/ZnS:Cu/BaTiO3/ZnS:Silver paste), WK-3 (ITO/BaTiO3/ZnS:Cu/BaTiO3/Silver paste), WK-4(ITO/BaTiO3+ZnS:Cu/Silver paste) As a result, structure of the highest brightness appeared WK-4 possessed 60 ${\mu}m$ thickness. The brightness was 2719 cd/$m^2$ at 100V, 400Hz.

• 한국안광학회지
• /
• 제14권1호
• /
• pp.57-62
• /
• 2009

목적: Magnetron의 세기를 비대칭으로 한 unbalanced magnetron sputtering 장치를 설계 제작하고 sus304시편 위에 TiN박막을 증착하여 색상과 경도에 관한 연구를 하고자 한다. 방법: 증착된 박막표면의 화학조성을 양적으로 분석하기 위하여 XPS high resolution scan과 curve fitting을 수행하였으며, 박막 표면의 경도를 측정하기 위해 nano indentation 장비를 이용하였다. 결과: 박막 두께가 두꺼워지면 박막의 색상은 처음에는 연한 금색, 시간이 지남에 따라 어두운 금색, 연보라, 남색으로 바뀌었다. 두께에 따른 박막의 색상변화는 박막에$TiO_{x}N_{y}$, $TiO_2$, TiN과 같은 세가지 화합물의 조성변화에 기인함을 알 수 있었으며,$ TiO_{x}N_{y}$의 조성변화가 두께에 따른 색상변화에 가장 큰 영향을 미치는 것을 여겨졌다. 결론: TiN박막의 비커스 경도가 TiN의 일반적인 경도보다 수치가 작은 것은 박막이 TiN, $TiO_2$,$TiO_{x}N_{y}$ 세가지 물질 섞여 있기 때문이라고 여겨지며, 두께에 따른 박막의 경도가 점점 커지다가 줄어드는 것은 두께에 따른 TiN 양과 밀접한 관계가 있음을 알 수 있었다.