• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.45-47
• /
• 2004

We have investigated the microstructures and the mechanical properties of TiA1/Cerameti1721 (Ag-Cu-Ti insert metal)/AISI4140 joints at 800$^{\circ}C$ for 60 to 300s using induction brazing method. Two continuous reaction layers of AICuTi and AICu$_2$Ti were formed at the interface between the braze and TiAl, whose thickness increased with the brazing time. The braze consisted of Ag-rich, Ti-rich, CuTi and CuTi$_2$ phases. The maximum tensile strength achieved 296MPa, which was 71% of that of TiAl base metal, for the specimen bonded at 800$^{\circ}C$. Further increase of the brazing temperature and time resulted in constant deterioration of its bonding strength due to large amount of brittle IMC.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.16-16
• /
• 1991

Generally brittle eta phase produced during TiC deposition has a effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η), phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase)have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as follows; 1. by inserting underlayer eta phase were decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest grain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.168-175
• /
• 1992

The surface and interface morphology as well as the sheet resistance, and uniformity of TiSiz film are significantly improved and the lateral titanium silicide growth over the oxide spacer is minimized by the use of ion beam mixing and rapid thermal annealing in nitrogen ambient. In addition, TiSiz film formations on TiISi and TiISiOz system were also studied.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.1
• /
• pp.16-23
• /
• 1992

Generally brittle eta phase produced during TiC deposition has a bad effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η) phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase) have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as fellows; 1. by inserting underlayer eta phase was decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest gain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1165-1171
• /
• 2000

Ti-C-Ni 혼합분말을 이용하여 SHS 공정에 의해 TiC-Ni 복합체를 제조하였으며, 리칭(leaching) 공정을 통하여 Ni을 제거함으로써 TiC 분말을 얻었다. TiC 분말의 특성분석을 위하여 XRD, SEM, TEM, AES 등을 사용하였다. 리칭 공정에 의해 얻어진 TiC 분말은 구형을 유지하고 있으며, 평균 입자크기는 0.4$\mu\textrm{m}$였다. 구형 TiC 분말을 다시 Ni 분말과 혼합하여 소결한 후 특성을 분석하였다. 140$0^{\circ}C$에서 소결하였을 때 TiC 입자는 구형에서 각진 형태로 변화하였다. 기계적 특성결과 상용 TiC 분말을 사용하였을 때보다 SHS 공정에 의해 제조된 TiC 분말을 사용하여 소결하였을 경우 파괴 인성값이 약 20% 증가하였다.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.3
• /
• pp.157-164
• /
• 1998

Effects of alloying elements on the pitting behavior of Ti-Al intermetalic compounds in the electrolytic soution containing Cl- were investigated through electrochemical tets and corrosion morphologies. Corrosion potential increased in the case of Cr addition to Ti-48%Al, whereas it decreased in the case of Si and B addition. The simultaneous addition of Cr and Si increased passive current density and decrosion corrosion potential. The passive current density of N addtion was higher than that of B addition in H2SO4 solution. With the addition of alloying elements, The pitting resistance decreased in order of TiAl>TiAlSi>TiAlN>TiAlB>TiAlCr and whin siumultaneous addition, it decreased in order of TiAlCrSi>TiAlCrBN>TiAlCrrN. The surface merohology after pitting test showed that the TiAl coataining Si had for fewer pits than that containing Cr and N simultaneously.

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.38-43
• /
• 2009

In this study, we investigated photocatalytic ability of plasma sprayed $TiO_2$ and Ag sputtering $TiO_2$(Ag-$TiO_2$) coatings. A sputtering processes were adopted to coat the surface of $TiO_2$ with Ag(99.99%). Ag was sputtered at 10mA, 450V for $1{\sim}11$ seconds. $TiO_2$ and Ag-$TiO_2$ coatings were heat-treated at 250, 300, 350, $400^{\circ}C$ for $0{\sim}240$seconds. Photoelectrical conductivity was measured by four-point probe, and photodegradation was calculated by UV-V is spectrometer. Microstructure observation of $TiO_2$ and Ag-$TiO_2$ coatings were investigated by SEM. Crystal structure of $TiO_2$ and Ag-$TiO_2$ coatings were investigated by XRD. Qualitative analyses of $TiO_2$ and Ag-$TiO_2$ coatings were conducted by EDX. When $TiO_2$ coatings were heat-treated at $350^{\circ}C$ for 30 sec, photoelectrical conductivity and photodegradation were best. And in XRD analysis result, (101)/(110) relative intensity ratio of $TiO_2$(rutile) was comparably changed with photoelectrical conductivity. When Ag-$TiO_2$ coatings were heat-treated at $350^{\circ}C$ for 30 [sec] after sputtering Ag for 7 sec, Photoelectrical conductivity and photodegradation are best. Surface of coatings in such condition has very small and uniform Ag particles.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.240-248
• /
• 2002

$Fe_xTi_{l-x}O_2$ films (x=0.07 and 0.16) were grown by oxygen-plasma-assisted molecular beam epitaxy on rutile $TiO_2$(110). The same growth conditions were applied for both films in order to determine surface characteristics of grown films as a function of Fe composition. The films were characterized by several surface analysis techniques. The oxidation states of Ti and Fe in $Fe_xTi_{l-x}O_2$ films were found to be +4 and a mixture of +2 and +3, respectively. More $Fe^{3+}$ species exist in higher Fe doped film of $Fe_{0.16}Ti_{0.84}O_2$. The morphology of $Fe_{0.07}Ti_{0.93}O_2$ film shows tall rectangular and cylinderical islands growth on flat substrate-like surface. On the other hand, $Fe_{0.16}Ti_{0.84}O_2$ film consists of round shaped small islands showing somewhat rougher surface compared to the surface of $Fe_{0.16}Ti_{0.84}O_2$ film.

• Journal of Powder Materials
• /
• v.22 no.4
• /
• pp.266-270
• /
• 2015

The synthesis of NiTi alloy powders by hydrogen reduction and dehydrogenation process of NiO and $TiH_2$ powder mixtures is investigated. Mixtures of NiO and $TiH_2$ powders are prepared by simple mixing for 1 h or ball milling for 24 h. Simple-mixed mixture shows that fine NiO particles are homogeneously coated on the surface of $TiH_2$ powders, whereas ball milled one exhibits the morphology with mixing of fine NiO and $TiH_2$ particles. Thermogravimetric analysis in hydrogen atmosphere reveals that the NiO and $TiH_2$ phase are changed to metallic Ni and Ti in the temperature range of 260 to $290^{\circ}C$ and 553 to $639^{\circ}C$, respectively. In the simple-mixed powders by heat-up to $700^{\circ}C$, agglomerates with solid particles and solidified liquid phase are observed, and the size of agglomerates is increased at $1000^{\circ}C$. From the XRD analysis, the presence of liquid phase is explained by the formation and melting of $NiTi_2$ inter-metallic compound due to an exothermic reaction between Ni and Ti. The simple-mixed powders, heated to $1000^{\circ}C$, lead to the formation of NiTi phase but additional Ni-, Ti-rich and Ti-oxide phases. In contrast, the microstructure of ball-milled powders is characterized by the neck-grown particles, forming $Ni_3Ti$, Ti-oxide and unreacted Ni phase.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.66-66
• /
• 2011

Anodic titanium dioxide (TiO2) nanotubes are very attractive materials for gas sensors due to its large surface to volume ratios. The most widely known method for fabrication of TiO2 nanotubes is anodic oxidation of metallic Ti foil. Since the remaining Ti substrate is a metallic conductor, TiO2 nanotube arrays on Ti are not appropriate for gas sensor applications. Detachment of the TiO2 nanotube arrays from the Ti Substrate or the formation of electrodes onto the TiO2 nanotube arrays have been used to demonstrate gas sensors based on TiO2 nanotubes. But the sensitivity was much lower than those of TiO2 gas sensors based on conventional TiO2 nanoparticle films. In this study, Ti thin films were deposited onto a SiO2/Si substrate by electron beam evaporation. Samples were anodized in ethylene glycol solution and ammonium fluoride (NH4F) with 0.1wt%, 0.2wt%, 0.3wt% and potentials ranging from 30 to 60V respectively. After anodization, the samples were annealed at $600^{\circ}C$ in air for 1 hours, leading to porous TiO2 films with TiO2 nanotubes. With changing temperature and CO concentration, gas sensor performance of the TiO2 nanotube gas sensors were measured, demonstrating the potential advantages of the porous TiO2 films for gas sensor applications. The details on the fabrication and gas sensing performance of TiO2 nanotube sensors will be presented.