• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.185-188
• /
• 1999

Biepitaxial Y$_1Ba_2Cu_3O_{7-x}$ (YBCO) and La$_{0.2}Sr_{0.8}MnO_3$ (LSMO) thin films have been prepared on SrTiO$_3$ buffer layer and MgO seed layer grown on Al$_2O_3$(11${\bar{2}}$0)substrates by dc-sputtering with hollow cylindrical targets, respectively. We charaterized Josephson properties and significantly large magnetoresistance in YBCO and LSMO films with 45$^{\circ}$ grain boundary junction, respectively. The observed working voltage (I$_cR_n$) at 77 K in grain boundary junction was below 10${\mu}$V, which is typical I$_cR_n$ value of single biepitaxial Josephson junction. The field magnetoresistance ratio (MR) of LSMO grain boundary juncoon at 77K was enhanced to 13%, which it was significant MR value with high magnetic field sensitivity at a low field of 250 Oe. These results indicate that inserting the insulating layer instead of the grain boundary layer with metallic phase can be possible to apply a new SIS Josephson junction and a novel magnetic device using spin-polarized tunneling junction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.157-160
• /
• 2004

Ferroelectric $(Ba_xSr_{1-x})TiO_3$ (BST) thin films have been deposited on (001) MgO single crystals by a pulsed laser deposition (PLD) method. The structure of deposited BST thin films were investigated by an x-ray diffractometer. Calculated c-axis lattice parameters of the BST films exhibit a strong lattice distortion, which was not observed in ceramic BST at room temperature. This lattice distortion of BST has been attributed to strains caused by lattice constant difference between film and substrate, oxygen vacancies in BST film, and thermal expansion difference between film and substrate. Ferroelectric properties at 10 GHz have been measured using a HP 8510C vector network analyzer. Dielectric properties, capacitance tunability and quality factor, of the interdigitaed capacitors fabricated on BST films were calculated from the measured s-parameters. Two distinct behaviors in structural, opitical, and microwave properties of BST films were observed; below and above 200 mTorr of oxygen pressure in the deposition chmber.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1496-1498
• /
• 2003

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films were deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method according to the deposition condition. The optimum conditions of RF power and Ar/$O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about 18.75[${\AA}/min$] at the optimum condition. The capacitance characteristics had a stable value within ${\pm}4[%]$. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films were observed above 200[kHz].

• 센서학회지
• /
• 제18권5호
• /
• pp.343-348
• /
• 2009

$NiO{\cdot}(Co_{0.25}Mn_{0.75})_2O_3$(Mn-Ni-Co) and $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thick films were screen printed on Pt patterned alumina substrate to investigate the effects of sintering temperature on humidity and temperature sensing properties of ceramic sensors. A raise in sintering temperature increased resistance and B constant of the Mn-Ni-Co temperature sensor. This may have derived from the synergic effects of the reduction in charge carriers caused by the substitution of Co for Mn as well as the formation of microcracks from the difference in thermal expansion coefficients. Dependence of resistance on humidity of the Mn-Ni-Co temperature sensor, however, was not found. BST films sintered at temperatures in the range of $1100^{\circ}C$ to $1150^{\circ}C$ showed excellent humidity sensing properties. The BST humidity sensor was faster in its response than the Mn-Ni-Co temperature sensor. The humidity sensor, however, proved to be unstable under various temperatures, suggesting a need for a temperature stabilizing device. In contrast, the Mn-Ni-Co temperature sensor was stable under humid conditions.

• 한국결정성장학회지
• /
• 제11권6호
• /
• pp.252-258
• /
• 2001

($Ba_{0.7}Sr_{0.3})TiO_3$박막을 ITO-coated glass 기판위에 spin-coating법으로 제조하였다. 제조된 용액을 초음파 bath 내에서 초음파 처리하여 균일화를 촉진시킨 후 박막을 제조하여 초음파 처리하지 않은 용액으로 제조한 박막과의 비교를 통하여 초음파 효과를 알아보았다. 용액의 초음파 처리로 박막의 결정화 온도를 다소 낮추었으며 박막의 표면이 보다 균일하고 치밀화되었고 거칠기도 8.4nm에서 5.6nm로 더 낮아졌다. 그리고 박막의 투광성 및 전기적 특성 또한 용액의 초음파 처리로 인하여 향상되었다.

• 한국재료학회지
• /
• 제11권11호
• /
• pp.997-1000
• /
• 2001

Conducting perovskite oxide, $(Ba,Sr)RuO_3(BSR)$, which has many advantages for $(Ba,Sr)TiO_3(BST)$ due to their similarity in crystal structure, lattice constant and chemical composition, was prepared on n-type Si (100) by liquid delivery metalorganic chemical vapor deposition(LDMOCVD). The deposition characteristics of BSR were controlled by gas-phase mass-transfer in the experiment. The BSR films deposited at 50$0^{\circ}C$ and oxygen flow rate of 100 sccm(standard cc/min) showed an average roughness of 22 $\AA$and resistivity of 810 $\mu$$\Omega$-cm. The roughness of BSR films with oxygen flow rate showed a close relationship with the resistivity of films. BSR (110) peak shifted toward lower Bragg angle with increase of x in the$(Ba_x,Sr_{1-x})TiO_3$. The resistivity of BSR films increased from 810 to 924 $\mu$$\Omega$-cm with increase of Ba content(x).

• 한국재료학회지
• /
• 제5권6호
• /
• pp.754-762
• /
• 1995

차세대 LSI용 유전체 박막으로서의 응용을 목적으로 RF 마그네트론 스퍼터링법으로 Si기판위에 SrTiO$_3$박막을 제조하였다. Ar과 $O_2$혼합가스 비, 바이어스 전압변화, 열처리 온도등의 증착조건을 다양하게 변화시키며 SrTiO$_3$박막을 제조하여 최적의 증착조건을 조사하였다. 박막의 결정성을 XRD로, 박막과 Si 사이의 계면의 조성분포를 AES로 각각 분석하였다. Ar과 $O_2$의 혼합가스를 스퍼터링 가스로 사용함으로써 결정성이 좋은 박막을 얻었다. 그리고 보다 치밀한 박막을 얻고자 바이어스 전압을 걸어주며 증착시켰다. 본 실험결과에서는 스퍼터링 가스는 Ar+20% $O_2$혼합가스, 바이어스 전압은 100V에서 좋은 결정성을 얻었다. 또한 하부전극으로 Pt, 완충층으로 Ti를 사용함으로써 SrTiO$_3$막과 Si 기판과의 계면에서 SiO$_2$층의 형성을 억제할 수 있었으며, Si의 확산을 막을 수 있었다. 전류 및 유전특성을 측정하기 위해 Au/SrTiO$_3$/Pt/Ti/SiO$_2$/Si로 구성된 다층구조의 시편을 제작하였다. Pt/Ti층은 RF 스퍼터링으로, Au 전극은 DC 마그네트론 스퍼터링법으로 증착시켰다 $600^{\circ}C$로 열처리함에 의해 미세하던 결정림들이 균일하게 성장하였으며, 이에 따라 유전율이 증가하고 누설전류가 감소하였다. $600^{\circ}C$에서 열처리한 두께 300nm의 막에서 유전율은 6.4fF/$\mu\textrm{m}$$^2$이고, 비유전상수는 217이었으며, 누설전류밀도는 2.0$\times$$10^{-8}$ A/$\textrm{cm}^2$로 양질의 SrTiO$_3$박막을 제조하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.480-483
• /
• 2001

Epitaxial rutile-TiO$_2$ and anatase-TiO$_2$ films were grown at 80$0^{\circ}C$ on $Al_2$O$_3$ (1102) and LaAlO$_3$ (001), respectively, using pulsed laser deposition. The formation of different phases on different substrates could be qualitatively explained by the atomic arrangements at the interfaces. We also successfully deposited epitaxial rutile-TiO$_2$ and anatase-TiO$_2$ films on conductive RuO$_2$ and La$_{0.5}$Sr$_{0.5}$CoO$_3$ electrodes, respectively Using a Kelvin probe, we measured the photovoltaic properties of these multilayer structures. A rutile-TiO$_2$ film grown on RuO$_2$ showed a very broad peak in the visible light region. An epitaxial anatase-TiO$_2$ film grown on La$_{0.5}$Sr$_{0.5}$CoO$_3$ showed a strong peak with a threshold energy of 3.05 eV 3.05 eV

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.27-28
• /
• 2009

In this study, we have fabricated the 3 wt% $Li_2CO3$ doped $(Ba,Sr)TiO_3$ thick films on the Ag/Pd printed $Al_2O_3$ substrates for the LTCCs (Low Temperature Co-fired Ceramics) applications. From the X-ray diffraion analysis, 3 wt% $Li_2CO3$ doped BST thick films on the Ag/Pd printed $Al_2O_3$ substrates, which sintered at 900 $^{\circ}C$ have perovskite structure without any pyro phase. The dielectric properties of 3 wt% $Li_2CO3$ doped BST thick films were measured from 1 kHz to 1 MHz. To investigate the electrical properties of 3 wt% $Li_2CO3$ doped BST thick films, we employed the impedance spectroscopy. The complex impedance of 3 wt% $Li_2CO3$ doped BST thick films were measured from 20 Hz to 1 MHz at the various temperatures.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.480-483
• /
• 2001

Epitaxial rutile-$TiO_2$ and anatase-$TiO_2$ films were grown at $800^{\circ}C$ on $Al_2O_3$ (1102) and $LaAlO_3$ (001), respectively, using pulsed laser deposition. The formation of different phases on different substrates could be qualitatively explained by the atomic arrangements at the interfaces. We also successfully deposited epitaxial rutile-$TiO_2$ and anatase-$TiO_2$ films on conductive $RuO_2$ and $La_{0.5}Sr_{0.5}CoO_{3}$ electrodes, respectively. Using a Kelvin probe, we measured the photovoltaic properties of these multilayer structures. A rutile-$TiO_2$ film grown on $RuO_2$ showed a very broad peak in the visible light region. An epitaxial anatase-$TiO_2$ film grown on $La_{0.5}Sr_{0.5}CoO_{3}$ showed a strong peak with a threshold energy of 3.05 eV.