• Journal of the Korean Society of Radiology
• /
• v.2 no.1
• /
• pp.31-34
• /
• 2008

The neutron capture spectrum for the light nuclide was very useful to study the nuclear structure. In the present study, the capture gamma-ray from the 27-keV resonance of $^{19}F(n,g)^{20}F$ reaction were measured with an anti-Compton NaI(Tl) spectrometer and the 3-MV Pelletron accelerator of the Research Laboratory for Nuclear Reactors at the Tokyo institute of technology. A neutron Time-of-Flight method was adopted with a 1.5 ns pulsed neutron source by the $^7Li(p,n)^7Be$ reaction. In the present experiment, a Teflon(($CF_2$)n) sample was used The sample was disk with a diameter of 90mm. The thickness of sample was determined so that reasonable counting rates could be obtained and the correction was not so large for the self-shielding and multiple scattering of neutrons in the sample, and was 5mm. The primary gamma-ray transitions were compared with previous measurement of Kenny.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.39 no.2
• /
• pp.72-81
• /
• 2016

There can be included a variety of uncertainties in all measurement results whether we can perceive or not on the causes. These uncertainties may end up in lowering the reliability of measurement results and also deteriorate the level of quality. For the purpose, we tried to combine the strengths of measurement uncertainty and measurement system analysis together to present a practical flowchart so as to verify those potential variation factors in general measurement processes. As a case study, we did an experiment and gathered data on the length between two holes of an engine cylinder head which is a core part for vehicles with a coordinate measuring machine and estimated nine uncertainty factors of it. Consequently, it was identified that the four primary factors among the nine which were related to the measurement standard, random errors or spread of the repeat measurements, differences between the coefficients of thermal expansion and the environment especially had been the influence around the laboratory. Since it is impossible to analyze the equipment and appraisal variations respectively through the only measurement uncertainty, we have used the measurement system analysis following the flowchart. Showing the result of being just about 0.5% lower for the appraisal variation, and the equipment variation occupied about 7% for the total Gage R&R. Through this research, we have come to a conclusion that much more detail analysis on variation factors can be possible to be identified in measurement processes by using the developed flowchart which is composed of measurement uncertainty and measurement system analysis. Therefore, we expect engineers who are involved in quality and measurements to utilize this developed method.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.32 no.2
• /
• pp.172-181
• /
• 2022

Objectives: In order to reduce the burden on employers and increase the reliability of measurement results, improvements to the provisions related to the work environment measurement reporting system, such as the current Occupational Safety and Health Act and its Enforcement Rules, are planned. This study aimed to suggest improvements for the work environment measurement reporting system through a survey and Delphi investigation. Method: This survey included workplaces (health managers), national institutions (the Ministry of Employment and Labor) that use the results of the work environment measurement reporting system for policy and supervision purposes, and work environment measurement institutions that enter the results were included. In addition to the survey, we tried to derive results through meetings with stakeholders and expert advisory meetings. Results: It is difficult to abolish or partially improve the reporting system under the Enforcement Regulations of the Occupational Safety and Health Act at this point because the opinions of workplaces, supervisory agencies, and measuring agencies differ in terms of its intended purpose and use. In the case of high-exposure harmful factors (over 50% on the basis of exposure) in the "comprehensive opinion" described in the work environment measurement results table, it is necessary to insert unit of work with exposed harmful factors, exposure factors, and current conditions in checklists or tables so that they can be reflected in government policies. In the case of workplaces that are feared to be highly exposed to substances subject to measurement, it seems desirable to improve them so that industrial health instructors registered with the Korea Safety and Health Agency or local labor offices can provide technical guidance. As an improvement plan to increase the reliability of data and the use of big data, it is necessary to improve the input method for processes and jobs. Conclusion: The laws and regulations of the work environment measurement reporting system are difficult to revise due to a lack of consensus among current stakeholders, but improvements can be achieved by improving the Ministry of Employment and Labor's notifications and other means. In addition, in order to effectively utilize the data from the K2B system, it is necessary to improve the input method for processes and jobs.

• Journal of the Korea Safety Management & Science
• /
• v.21 no.2
• /
• pp.15-23
• /
• 2019

Among service industries of knowledge based economic era, the roles of educational service field are becoming more important and standard of educational service makes a direct effect on economic development and social growth. Therefore, accurate measurement of service quality is the most important assignment and the measurement of the service quality remains difficult assignment. So, this researcher classified quality attributes applying weighted value and found potential satisfaction level(PSL) and potential customer demand improvement index(PCDI) for trainees participating in national manpower business so as to suggest measurement of service quality and easiness of use and then, calculated satisfaction position and opportunity cost by quality factor with Taguchi's loss fraction. And, improvable satisfaction level was measured, opportunity cost by degree of customer dissatisfaction was quantitatively measured, and a model that can indicate with economic factors was suggested. In addition, methodology of measuring quality cost that can be reduced by quality improvement and direction of strategic decision-making for deciding items to be improved preferentially were suggested with qualitative index that can indicate the degree of customers' dissatisfaction by loss.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.2
• /
• pp.81-86
• /
• 2006

The machining parts must be produced within the specification of drawing and those will be able to meet function and efficiency. At that time, it is very important not only precision machine and machining technique but also the measurement technique. So, the improvement of measurement technique is to be joined together at once with improvement of machining technique. Finally, the quality and value of the parts are decided by precision measurement. This paper aims to study on the machined surfaces characteristics of aluminum alloy by AFM(Atomic force microscope) measurement. The objective is contribution to ultra-precision machining by exhibit foundation data of surface roughness and tool wear when parts are cutting with diamond tool at the factory.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.104-111
• /
• 2003

Micro force measurement is required more frequently for a precision manufacturing and investment in fields of precision industries such as semiconductor, chemistry and biology, and so forth. Null balance method has been introduced as an alternative of a loadcell. Loadcells have advantages in aspects of low cost and easy manufacturing, but have also the limitation in resolution and sensitivity to environment variations. In this paper, null balance method is explained and the dominant parameters related to system performances are mentioned. Null position sensor, electromagnetic system and controller are investigated. Also, the characteristic experiment is carried out in order to estimate the resolution and the measurement range. In order to overcome the limitation by the drift of position sensor and the performance of controller, double electromagnetic force compensation method is proposed and experimented. After controlling and filtering, the resolution under $\pm$ 1mg and measurement range over 300g could be obtained.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2002.05a
• /
• pp.253-257
• /
• 2002

So far. the common elasticity data of textile fabrics has not been present because the method depends on the knowledge of measurement operators. In this paper, the new measurement equipment using road cel1 is presented to measure the coefficient of textile fabrics in real time. The measurement method is based on the volta among textile fabrics. The textiles with strong elasticity are high voltage produced from others are low. The presented method can be applied to visualize the textile, sew the cloth, control textile fabrics. Also. these measurement datum are used to B2B electronic trading system.

• Nuclear Engineering and Technology
• /
• v.56 no.2
• /
• pp.444-450
• /
• 2024

Based on multiple measurements of ionization loss, the Time Projection Chamber (TPC) combines strong tracking ability with particle identification ability in a large momentum range, which is an important advantage of TPC detection technology over traditional ionization measurement technology. According to these two characteristics of TPC, applying it to the measurement of fission cross-section can greatly improve the measurement accuracy. During the measurement of the fission cross-section, the number of target nuclei is required to be accurately measured. So this paper introduces a method for measuring the number of ²³⁵U target nuclei using a fission TPC system. The measurement result agrees with the reference value, and relative error is around 1 %.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.567-576
• /
• 2007

In order to assess the on-site applicability of 3D absolute displacement monitoring of tunnel using digital photogrammetry, the displacement of the optical target placed at the measurement section was investigated, as planned in the OO tunnel construction site. The targets on 3 measurement lines only were considered for each point of measurement for the reconstruction of 3D cubic model for the digital vision monitoring. For each 3D model, 3 or more images have to be obtained at each point. On the last 2 measurement lines, 6 targets (crown, left and right walls) were continuously overlapped to construct 3D models so that 6 or more apices can be shared by 2 3D models. In order to compare the measurement methods of 3D absolute displacements in tunnel excavation, i. e, total station and digital image measurement, both the digital image measurement and optical measurement were conducted for 10 times in the same work section. The time and measurement results of both methods were compared.

• Journal of Korean Society of Forest Science
• /
• v.3 no.1
• /
• pp.28-31
• /
• 1963

Recognizing shortcomings and unreasonable points of the usual methods of measurement of the standing-tree volume, author contrived measurement formula of standing-tree volume which is based on stem-curve equation, $y^2=2px$, resulted from the analysises and experiments on stem-curve by differentiation & integration. The results of this study are as follows ; (1) The following is the formula. $V=1/2g_{1.2}$(h+1.2) V=volume of tree $g_{1.2}$ = sectional area at breast heigh h = height of tree (2) So plain is the form of this formula that this formula is more convenient than usual formulas in measuring. (3) The percentage error of this formula is negative and it is remarkably superior to usual formulas except Pressler's formula, in other words, the higher the tree that is measured is, the more inaccurate become pressler's formula, and the percentage error of the breast-height form factor method is direct proportion to the grossness of the tree that is measured, but the higher the tree that is measured, the lower become percentage error of this formula in geometrical progression.