• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.585-585
• /
• 2012

$Cu(In_{1-x}Ga_x)Se_2$(CIGS) 박막 태양전지는 Chalcopyrite 계 박막 태양전지로 Cu, In, Ga, Se 각 원소의 조성을 적절히 조절하여 박막을 성장시킨다. 성장시킨 CIGS 박막은 광흡수계수가 $10^5cm^{-1}$로 다른 물질보다 뛰어나고 직접 천이형 반도체로서 얇은 두께로도 고효율의 박막 제작이 가능하다. CIGS 태양전지를 제조하는 방법은 3-stage 동시 증착법, 금속 전구체의 셀렌화 공정법, 전기 증착법 등이 있다. 그 중에 금속 전구체의 셀렌화 공정법은 다른 제조 방법에 비해 대면적 생산에 유리한 장점이 있다. 하지만 아직 상대적으로 3-stage 동시 증착법에 비해 낮은 에너지 변환 효율이 보고된다. 본 실험에서는 기존의 금속 전구체의 셀렌화 공정법과는 달리 전구체 증착과 셀렌화 공정을 동시에 하고, Se cracker를 통하여 Se 원료를 주입하는 방식인 반응성 스퍼터링 공정에서 reservoir zone의 온도 변화에 따른 특성을 분석하였다. Se cracker의 reservoir zone 온도가 증가할수록 Cu/(In+Ga) 비가 증가한다. CIGS 박막 태양전지의 구조는 Al/Ni/ITO/i-ZnO/CdS/CIGS/Mo/Soda lime glass이다. CIGS 박막의 조성비가 Cu/(In+Ga)=0.89, Ga/(In+Ga)=0.17인 박막 태양전지에서 개방전압 0.34 V, 단락전류밀도 $32.61mA/cm^2$, 충실도 56.2% 그리고 변환 효율 6.19%를 얻었다. 본 연구는 2011년도 지식경제부의 재원으로 한국에너지 기술평가원(KTEP)의 지원을 받아 수행한 연구 과제입니다(No.20093020010030).

• Journal of the Korean Chemical Society
• /
• v.15 no.2
• /
• pp.55-63
• /
• 1971

In this study, several nickel catalysts for the steam-hydrocarbon reforming process were prepared from various nickel salt, magnesium oxide, alumina and kaolinite. The activity and strength of the catalysts were investigated. 1. The proper composition of the calcined catalysts are: NiO (5-15%)-MgO(10-20%)-$Al_2O_3$(10-40%)-Kaolinite(50-80%). 2. The admixed or cosedimented ingredients of the catalysts was pelletized and calcinated at 1000 or $1150^{\circ}C$. Calcination at $1150^{\circ}C$ for an hour was optimum. 3. The water to oil ratio (W/O) for reforming of hexane should be above 7 mole/mole. As the W/O increases, more carbon dioxide and hydrogen, but less carbon monoxide was produced. Also carbon deposition become lessen at higher W/O. 4. Maximum conversion had attained at about $850^{\circ}C$. As the reaction temperature increases, more carbon monoxide and hydrogen, but less carbon dioxide and lower hydrocarbon was produced. 5. The percent conversion at $850^{\circ}C$ was about 80%, using a catalyst which the nickel oxide content are 5%.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.3
• /
• pp.168-173
• /
• 2011

The availability, low toxicity, and high degree of technological development make silicon the most likely material to be used in solar cells, the cost of solar cells depends entirely on cost of high purity silicon production. The present work was conducted to electrodeposite of silicon from $K_2SiF_6$, an inexpensive raw material prepared from fluorosilicic acid ($H_2SiF_6$) produced in Iraqi Fertilizer plants, and using inexpensive graphite material as cathode electrode. The preparation of potassium fluorosilicate was performed at ($60^{\circ}C$) in a three necks flask provided with a stirrer, while the electro deposition was performed at $750^{\circ}C$ in a three-electrodes configuration with melt containing in graphite pot. High purity potassium fluorosilicate (99.25%) was obtained at temperature ($60^{\circ}C$), molar ratio-KCl/$H_2SiF_6$(1.4) and agitation (600 rpm). Spongy compact deposits were obtained for silicon with purity not less than (99.97%) at cathode potential (-0.8 V vs. Pt), $K_2SiF_6$ concentration (14% mole percent) with grain size (130 ${\mu}m$) and level of impurities (Cu, Fe and Ni) less than (0.02%).

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.2
• /
• pp.245-265
• /
• 1991

The purpose of this study was to observe the changes of the elemental transmission and bond strength between the metal and porcelain according to various kinds of ion beam mixing method. ion beam mixing of $meta1/SiO_2$ (silica), $meta1/Al_2O_3$(alumina) interfaces causes reactions when the $Ar^+$ was implanted into bilayer thin films using a 100KeV accelerator which was designed and constructed for this study. A vacuum evaporator used in the $10^{-5}-10^{-6}$ Torr vacuum states for the evaporation. For this study, three kinds of porcelain metal selected, -precious, semiprecious, and non-precious. Silica and alumina were deposited to the metal by the vacuum evaporator, separately. One group was treated by two kinds of dose of the ion beam mixing $(1\times10^{16}ions/cm^2,\;5\times10^{15}ions/cm^2)$, and the other group was not mixed, and analyzed the effects of ion beam mixing. The analyses of bond strength, elemental transmissions were performed by the electron spectroscopy of chemical analysis (ESCA), light and scanning electron microscope, scratch test, and micro Vickers hardness tests. The finding led to the following conclusions. 1. In the scanning electron and light microscopic views, ion beam mixed specimens showed the ion beam mixed indentation. 2. In the micro Vickers hardness and scratch tests, ion beam mixed specimens showed higher strength than that of non mixed specimens, however, nonprecious metal showed a little change in the bond strength between mixed and non mixed specimens. 3. In the scratch test, ion beam mixed specimens showed higher shear strength than that of non treated specimens at the precious and semiprecious groups. 4. In the ESCA analysis, Au-O and Au-Si compounds were formed and transmission of the Au peak was found ion beam mixed $SiO_2/Au$ specimen, simultaneously, in the higher and lower bonded areas, and ion beam mixed $SiO_2/Ni-Cr$ specimen, oxygen, that was transmitted from $SiO_2\;to\;SiO_2/Ni-Cr$ interface combined with 12% of Ni at the interface.

• Korean Journal of Metals and Materials
• /
• v.47 no.2
• /
• pp.129-137
• /
• 2009

Corrosion behaviors of TiN coated dental casting alloys have been researched by using various electrochemical methods. Three casting alloys (Alloy 1: 63Co-27Cr-5.5Mo, Alloy 2: 63Ni-16Cr-5Mo, Alloy 3: 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting(CF), high frequency induction casting(HFI) and vacuum pressure casting(VP). The specimens were coated with TiN film by RF-magnetron sputtering method. The corrosion behaviors were investigated using potentiostat (EG&G Co, 263A. USA) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The corrosion morphologies were analyzed using FE-SEM and EDX. Alloy 1 and Alloy 2 showed the ${\alpha}-Co$ and ${\varepsilon}-Co$ phase on the matrix, and it was disappeared in case of TiN coated Alloy 1 and 2. In the Alloy 3, $Ni_2Cr$ second phases were appeared at matrix. Corrosion potentials of TiN coated alloy were higher than that of non-coated alloy, but current density at passive region of TiN coated alloy was lower than that of non-coated alloy. Pitting corrosion resistances were increased in the order of centrifugal casting, high frequency induction casting and vacuum pressure casting method from cyclic potentiodynamic polarization test.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.799-816
• /
• 2023

Mineralogical and geochemical studies of shales within the Lower Anambra Basin was conducted to unravel the depositional environment, provenance, maturity, paleo-weathering conditions, and tectonic settings. Mineralogical studies conducted using X-ray diffraction analysis revealed that the samples were composed of kaolinite, montmorillonite, chlorite, and illite. KaolinIite is the dominant mineral, constituting approximately 41.5% of the bulk composition, whereas the non-clay minerals are quartz, ilmenite, and sillimanite. Geochemical analysis showed a predominance of SiO₂, Al₂O₃, and Fe₂O₃ contents of the shale samples with mean values of 52.29%, 14.09%, and 6.15% for Imo Shale (IS); 52.31%, 16.70%, and 7.39% for Mamu Shale (MS); 43.21%, 21.33%, and 10.36% for Enugu Shale (ES); 53.35%, 15.64%, and 7.17% for Nkporo Shale (NS); and 51.24%, 17.25%, and 7.78% for Agwu Shale (AS). However, the shales were depleted in Na₂O, MgO, K₂O, MnO, TiO₂, CaO, and P₂O₅. The trace element ratios of Ni/Co and Cu/Zn of the shale suggest an oxic depositional environment. The average SiO₂ vs. Al₂O₃ ratio of the shales indicated textural maturity. Compared to the PAAS standard, the shales plot below the PAAS value of 0.85, suggesting a high degree of maturity and intensive chemical weathering, further confirmed on a CIA vs. PIA plot. On log (K₂O/Na₂O) against SiO₂ and tectonic setting discriminant function diagrams, the shales plot mostly in the field of passive continental margin tectonic setting. The discriminant function diagrams as well as Al₂O₃/TiO₂ ratio of the shales showed that they were derived from a mixed source (mafic and intermediate igneous rocks).

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.4
• /
• pp.478-483
• /
• 2014

Objectives: The main objective of this study is to assess the levels of hazardous substances in floor dust in primary schools located in the city of Busan in Korea. Materials and Methods: An on-site investigation of three primary schools was performed between April and May 2013. The hazardous substances measured in this study were 14 heavy metals (Cu, Fe, Pb, Mn, Ni, Zn, Cr, Cd, As, Al, Sn, Co, Mo and Si) and the biological agents were bacteria, fungi and endotoxin). Results: Among the heavy metals, Cd, Co, Pb and Cr were not detected in the floor dust from the three primary schools. The mean levels of other heavy metals were as follows: $20({\pm}10)ng/cm^2$ for As, $30({\pm}20)ng/cm^2$ for Al, $5({\pm}4)ng/cm^2$ for Sn, $20({\pm}20)ng/cm^2$ for Mo, $1,340({\pm}620)ng/cm^2$ for Si, $110({\pm}100)ng/cm^2$ for Cu, $240({\pm}50)ng/cm^2$ for Fe, $30({\pm}30)ng/cm^2$ for Mn, $10({\pm}10)ng/cm^2$ for Ni, and $50({\pm}30)ng/cm^2$ for Zn. It was found that mean concentrations of bacteria, fungi and endotoxin in the floor dust of primary schools were $4.7{\time}10^7({\pm}2.2{\time}10^7)cfu/cm^2$, $6.3{\time}10^6({\pm}6.4{\time}10^6)cfu/cm^2$, and $8,140({\pm}5,801)EU/cm^2$, respectively. The predominant species identified in the floor dust of the primary schools were Pseudomonas spp. for bacteria and Penicillium spp.,Cladosporidium spp.,and Aspergillus spp. for fungi, which would be somewhat similar to the microbial distribution pattern of other general environments. Conclusions: Based on the results obtained from this study, the levels of heavy metals, microbes and endotoxin distributed in the floor dust of primary school were higher than those reported for other general facilities. Thus, preventive measures should be prepared for the health care of children.

• Journal of Technologic Dentistry
• /
• v.31 no.1
• /
• pp.55-61
• /
• 2009

Passive fitting of meso-structure and super-structures is a predominant requirement for the longevity and clinical success of osseointegrated dental implants. However, precision and passive fitting has been unpredictable with conventional methods of casting as well as for corrective techniques. Alternative to conventional techniques, electro discharge machining(EDM) is an advanced method introduced to dental technology to improve the passive fitting of implant prosthesis. In this technique material is removed by melting and vaporization in electric sparks. Regarding the efficacy of EDM, the application of this technique induces severe surface morphological and elemental alterations due to the high temperatures developed during machining, which vary between $10,000{\sim}20,000^{\circ}C$. The aim of this study was to investigate the morphological and elemental alterations induced by EDM process of casting dental gold alloy and non-precious alloy used for the production of implant-supported prosthesis. A conventional clinical dental casting alloys were used for experimental specimens patterns, which were divided in three groups, high fineness gold alloy(Au 75%, HG group), low fineness gold alloy(Au 55%, LG group) and nonprecious metal alloy(Ni-Cr, NP group). The UCLA type plastic abutment patterns were invested with conventional investment material and were cast in a centrifugal casting machine. Castings were sandblasted with $50{\mu}m\;Al_2O_3$. One casting specimen of each group was polished by conventional finishing(HGCON, LGCON, NPCON) and one specimen of each group was subjected to EDM in a system using Cu electrodes, kerosene as dielectric fluid in 10 min for gold alloy and 20 min for Ni-Cr alloy(HGEDM. LGEDM, NOEDM). The surface morphology of all specimens was studied under an energy dispersive X-ray spectrometer (EDS). The quantitative results from EDS analysis are presented on the HGEDM and LGEDM specimens a significant increase in C and Cu concentrations was found after EDM finishing. The different result was documented for C on the NPEDM with a significant uptake of O after EDM finishing, whereas Al, Si showed a significant decrease in their concentrations. EDS analysis showed a serious uptake of C and Cu after the EDM procedure in the alloys studied. The C uptake after the EDM process is a common finding and it is attributed to the decomposition of the dielectric fluid in the plasma column, probably due to the development of extremely high temperatures. The Cu uptake is readily explained from the decomposition of Cu electrodes, something which is also a common finding after the EDM procedure. However, all the aforementioned mechanisms require further research. The clinical implication of these findings is related with the biological and corrosion resistance of surfaces prepared by the EDM process.

• 한국해양학회지
• /
• v.22 no.1
• /
• pp.43-56
• /
• 1987

A study on sedimentation, geochemical behavior and seismic stratigrapht of the continental shelf sediments along the Korea Strait and a part of south and southeast offshore area of the Korea Peninsula was carried out. In the inner shelf floor with depth ranging up to 80m zonal distribution patterns of mud, sandy silt, and silty sand were observed. In the outer shelf, however, coarse sandy sediments are dominant, and shills and gravels were frequently observed. These observations seem to confirm the Holocene sedimentary processes on the continental shelves off the south, south to east coasts of Korea discussed by Park (1985 and 1986) and Park and Choi (1986). The suface sediments (upper most 5cm thick)from selected 9 stations were analyzed for Al,Mn, Fe,Cr,Ni,Cu,Zn and Pb in order to study geochemical behavior of the sediments in the study area. All data were normalized to Al to com,pensate the size effect of the sediments.In general,inner shelf sediments show slight enrichment compared to the outer shelf sediments.In particular,Pb and Zn show heavy enrichment in most of the sediments.to degrees comparable to those observed at the polluted Kwangyang and Masan Bay sediments.Thus,it is considered that rapid migration or movement of fine-grained sediments in the study area does exist. Three seismic stratigraphic units were analyzed based on the seismic records.The acoustic basement the lower sedimentary deposit(B)and the upper deposit(A)were observed.The strong reflectivity R,in particular, between unit A and B is considered to be an erosinal unconformity during the last Glacial time.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.1
• /
• pp.59-64
• /
• 2006

Ion exchange resin particles should not be found in steam generator(S/G) sludge. The suspicious spherical resin particles observed in S/G sludge sample were characterized for particle size distribution under optical microscope using the micro-technique, for element analysis by the electron probe micro analysis (EPMA), and for molecular identification by the IR spectroscopy. The particle sizes are distributed from 1 to $200{\mu}m$ for the sludge, while 40 to $500{\mu}m$ for the spherical resin particles. The results of the elemental analysis showed different major impurities: Si, Al, Mn, Cr, Ni, Zn and Ti for the sludge particles, while Si, Cu, Zn for the spherical resin particles. However, both particles contain Fe as a matrix of magnetite $(Fe_3O_4)$. IR spectrum of the spherical particles was not quite similar to the IR spectrum of ion exchange resins used in S/G system. These results indicate that the spherical particles are not related to ion exchange resin particles and may be formed by the process of the sludge formation.