• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.11
• /
• pp.874-879
• /
• 1991

The effect of air gap between specimen and jig on the material constant (permittivity, permeability) and attenuation characteristics of electromagnetic wave absorbers in the coaxial line method was investigated. The presence of a air gap made both permittivity and permeability measured lower than true value, and the tendency was greater in the case of permittivity. An inner gap compared to an outer gop was found to yield a larger difference between measured and true values. The effect of air gap was measured for a Ni0.3Zn0.7Fe2O4, with the gap eliminated by metallizing with Ag-paste. The measured characteristics were in good agreement with corrected values by calculation.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.7
• /
• pp.703-708
• /
• 2001

K2NiF4-type organic-based perovskites of the (C4H9NH3)2FexPb1-xCl4 (x=0.00, 0.25, 0.50, and 0.75) system have been synthesized using a low-temperatu re solution method under a flowing argon gas. When stoichiometric butylamine, iron chloride, and lead chloride are mixed, a yellow solution are obtained from slow cooling of 90 to -10 $^{\circ}C.$ The final product is a plate-like yellow crystal. The X-ray crystallographic analysis has been carried out using XRD in the range of $5^{\circ}{\leq}$ 2${\theta}$ ${\leq}80^{\circ}.$ The local symmetry around the absorbing Pb atom of the samples has been determined by the EXAFS spectroscopic study. The crystals assign to orthorhombic system by the XRD analysis. The FT-IR spectra are analyzed in the range of 600 to 3300 cm-1 . DSC and TGA are measured to detect thermal stability between 30 and 300 $^{\circ}C.$ Two endothermic peaks are detected in all samples. The electrical conductivity has been measured using the four-probes technique for the (C4H9NH3)2FexPb1-xCl4 system in 300-460 K. Photoluminescence phenomenon was also investigated at room-temperature.

• Korean Journal of Food Science and Technology
• /
• v.34 no.4
• /
• pp.552-558
• /
• 2002

Polyphenol oxidase from Flammulina velutipes was purified and characterized. Purification of polyphenol oxidase was achieved by ammonium sulfate precipitation, Superdex G-200 gel filtration chromatography, Phenyl superose affinity chromatography, Mono-Q anion exchange chromatography and Superdex S-200 gel filtration chromatography on FPLC. After these purification steps specific activity of purified polyphenol oxidase increased to 199.1 units/mg. Polyphenol oxidase from F. velutipes was composed of a single polypeptide with molecular weight of about 40 kDa. Optimum pH and temperature for the enzyme reaction were found to be 6.0 and $25^{\circ}C$, respectively. The activity of the enzyme gradually decreased at acidic pH between 3 and 5, and the enzyme lost its activity at alkaline pH between 8 and 10. This enzyme exhibited high substrate specificity to o-diphenols. Km-values for L-DOPA and caffeic acid were found to be 3.97 mM and 1.78 mM, respectively. 2-mercaptoethanol, L-ascorbic acid, sodium bisulfite, EDTA and $Mg^{2+}$ inhibited the activity of pholyphenol oxidase and $Cu^{2+}$, $Fe^{2+}$, $Zn^{2+}$ and $Ni^{2+}$ increased enzyme activity. The activity of enzyme was well maintained at $-70^{\circ}C$ for over 4 months, and at $-20^{\circ}C$ for 1 months.

• Economic and Environmental Geology
• /
• v.31 no.2
• /
• pp.111-125
• /
• 1998

Dispersion, migration and enrichment of environmental toxic elements from the Samkwang Au-Ag mine area were investigated based upon major, minor and rare earth element geochemistry. The Samkwang mine area composed mainly of Precambrian granitic gneiss. The mine had been mined for gold and silver, but closed in 1996. According to the X-ray powder diffraction, mineral composition of stream sediments and soils were partly variable mineralogy, which are composed of quartz, orthoclase, plagioclase, amphibole, muscovite, biotite and chlorite, respectively. Major element variations of the host granitic gneiss, stream sediments and soils of mining and non-mining drainage, indicate that those compositions are decrese $Al_2O_3$, $Fe_2O_3$, MgO, $TiO_2$, $P_2O_5$ and LOI with increasing $SiO_2$ respectively. Average compositional ranges (ppm) of minor and/or environmental toxic elements within those samples are revealed as As=<2-4500, Cd=<1-24, Cu=6-117, Sb=1-29, Pb=17-1377 and Zn=32-938, which are extremely high concentrations of sediments from the mining drainage (As=2006, Cd=l1, Cu=71, Pb=587 and Zn=481 ppm, respectively) than concentrations of the other samples and host granitic gneiss. Major elements (average enrichment index=6.53) in all samples are mostly enriched, excepting $SiO_2$, $Na_2O$ and $K_2O$, normalized by composition of host granitic gneiss. Rare earth element (average enrichment index=2.34) are enriched with the sediments from the mining drainage. Minor and/or environmental toxic elements within all samples on the basis of host rock were strongly enriched of all elements (especially As, Br, Cu, Pb and Zn), excepting Ba, Cr, Rb and Sr. Average enrichment index of trace elements in all samples is 15.55 (sediments of mining drainage=37.33). Potentially toxic elements (As, Cd, Cr, Cu, Ni, Pb, and Zn) of the samples revealed that average enrichment index is 46.10 (sediments of mining drainage=80.20, sediments of nonmining drainage=5.35, sediments of confluent drainage=20.22, subsurface soils of mining drainage=7.97 and subsurface soils of non-mining drainage=4.15). Sediments and soils of highly concentrated toxic elements are contained some pyrite, arsenopyrite, sphalerite, galena and goethite.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.21 no.2
• /
• pp.71-79
• /
• 1988

For the purpose of producing low salt fermented anchovy by accelerated method with a strong proteolytic bacteria, in this study, a strong proteolytic bacterium was isolated from low salt fermented anchovy and its bacteriological characteristics and properties of protease were experimented. The results obtained were as fellows : three proteolytic bacteria, Aeromonas anaerogenes Barillus subtilis and Staphylococcus saprophyticus were isolated from low salt fermented anchovy($4\%\;of\;salt,\;4\%\;of\;KCl,\;0.5\%\;of\;lactic\;acid,\;6\%$of sorbitol and $4\%$ of alcohol extract of red pepper) after 40 days fermentation. Among these strains, which grow best at $30^{\circ}C$, pH 7.0, B. subtilis was found the best proteolytic strain and benefit for industrial use as shown $0.95\;hr^{-1}$ of specific growth rate, $89{\mu}g-Tyr/hr.ml$ of maximum activity after 12 hrs culture in TPY broth. The protease produced by by B. subtilis showed maximum activity at $35^{\circ}C$, pH 7.0, and molecular weight was estimated to be 23,000 by Sephadex G-100 filtration, and it was supposed to be a kind of metal chelator sensitive neutral protease from the results of strong sensitivity against EDTA, o-phenanthroline and metal ions such as $Cu^{2+},\;Ni^{2+},\;Fe^{2+}.Km$ value of that by method of Lineweaver-Burk was determinded to be $0.73\%$ for casein as a substrate.

• Resources Recycling
• /
• v.2 no.4
• /
• pp.1-9
• /
• 1993

A study on the recovery of nitric and hydrofluoric acids is carried out with pulsed column extractor in order to the industrial application of this process. Firstly, from the continuous experiments about the recovery of acids using domestic stainelss steel pickling solution, it is found out that the free nitric and hydrofluoric acids are only extracted by 70% TBP and the heaby metals such as Fe, Cr and Ni are not extracted. The effectiveness of extraction and stripping generally improves as the pulse velocity(product of amplitude and frequency) is increased, optimum performance typically occuring slightly below an amplitude-frequency product which results in flooding the column because of excessive emulsification. When the pickling solution is treated by 70% TBP at a phase ratio of A/O=1/2 in the extraction and by distilled water at a phase ratio of O/A=1 in the stripping, the concentration of refined acides are 102g/$\ulcorner$ $HNO_3$and 8.8g/$\ulcorner$ HF, respectively and the recovery of $HNO_3$and HF are 90.7% and 75.2%, respectively.

• Economic and Environmental Geology
• /
• v.28 no.3
• /
• pp.259-269
• /
• 1995

Column leaching tests were conducted using fresh and weathered pulverised fuel ash of some 17 and 40 years old from two major British power plants, with deionised water and simulated synthetic industrial leachate. The former was to see the leaching behaviour of weathered ash and the latter was to see if the formation of secondary products from water and PFA interaction and ameliorating effect in removing metals from industrial leachates. Fresh PFA liberates elevated concentrations of surface-enriched inorganics, including Ca, Na, K, B, $Cr_{total}$, Li Mo, Se and $SO^{2-}_4$. This might indicate their association with the surface of PFA particles. In the column leaching tests using weathered ash and deionised water, elements are not readily leached but are released more slowly, showing relatively constant concentrations. For the case of weathered ash, some readily soluble surface-enriched elements appears to have been liberated in their early stage of leaching and the liberation of glass associated elements are thought to be more important function in controlling the element concentration. The result from column leaching tests exceed for a number of elements when compared with various Water Standards and suggests the leachate from PFA disposal mound needs dilution to achieve target concentrations. PF A shows element retention effect for many elements, including B, Fe, Zn, Hg, Ni, Li and Mo, in the order of fresh Drax ash > weathered Drax ash > Weathered Meaford ash in retaining capacity. Geochemical modelling using a computer program WATEQ4F reveals some solubility controlling secondary solid products. These include $CaSO_4{\cdot}2H_2O$ for Ca, $Al(OH)_3$ for Al and $Fe(OH)_3$ for Fe.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.327-332
• /
• 1999

The recovery activation energy, the order of reaction and the recovery rate constant were detemined by isochronal and isothermal annealing treatment to investigate the recovery behaviors of neutron irradiated Mn-Mo-Ni low alloy steels$(fluence: 2.3\times10^{19}ncm^{-2}, 553K, E\geq1.0 MeV)$. Vickers microhardness tests were conducted to trace the recovery behavior after heat treatments. The results were analyzed in terms of recovery stages, behavior of responsible defects and recovery kinetics. It was shown that recovery occurred through two annealing stages(stage I : 703-753K, stage n : 813-873K) with re$\infty$very activation energies of 2.5 eV and 2.93 eV for each stage I and n, respectively. From the comparison of unirradiated and irradiated isochronal anneal curves, a radiation anneal hardening(RAH) peak was identified at around 813K. Most of recovery have occurred during about 120 min irrespective of isothermal annealing temperatures of 743K and 833K. Recovery rate constants were determined to be $3.4\times10^{-4}min^{-1} and 7.1\times10^{-4}min^{-1}$ for stage I and II, respectively. The order of reaction was about 2 for both recovery stages. Comparing the obtained data with those of previously reported results on neutron irradiated Mn- Mo- Ni steels, the thermal recovery be­havior of the present material seems to occur by the dissociation of point defect clusters formed during irradiation, and by the recombination process of self-interstitials and vacancies from dissociated vacancy clusters.

• Resources Recycling
• /
• v.24 no.3
• /
• pp.27-33
• /
• 2015

EAFD (Electric Arc Furnace Dust) is considered as pernicious pollutant, assigned hazardous waste. Since this dust is a by-product of industry, it contains valuable metals such as Fe, Zn, Ni, Cu which can be turned into resources by recycling process. In this study, hydrometallurgical process was applied to recover Zn from Electric Arc Furnace Dusts. The result showed 95% Zn recovery at 3M $H_2SO_4$, Solids/Liquid ratio 1:2 and aeration of 1.8L/min for 2hr. However there was 80% Zn recovery at lower $H_2SO_4$ concentration apply for pilot scale plant.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.4
• /
• pp.547-555
• /
• 2014

Objective: This study was conducted to investigate the association between subjective distress symptoms and argon welding among workers in Gyeongnam Province shipyard. Method: 31 argon and 29 non-argon welding workers were selected as study subjects in order to measure concentrations of personal dust, welding fumes and other hazardous materials such as ZnO, Pb, Cr, FeO, MnO, Cu, Ni, $TiO_2$, MgO, NO, $NO_2$, $O_3$, $O_2$, $CO_2$, CO and Ar. An interviewer-administered questionnaire survey was also performed on the same subjects. The items queried were as follows: age, height, weight, working duration, welding time, welding rod amounts used, drinking, smoking, and rate of subjective distress symptoms including headache and other symptoms such as fever, vomiting and nausea, metal fume fever, dizziness, tingling sensations, difficulty in breathing, memory loss, sleep disorders, emotional disturbance, hearing loss, hand tremors, visual impairment, neural abnormality, allergic reaction, runny nose and stuffiness, rhinitis, and suffocation. Statistical analysis was performed using SPSS software, version 18. Data are expressed as the mean ${\pm}SD$. An ${\chi}^2$-test and a normality test using a Shapiro wilk test were performed for the above variables. Logistic regression analysis was also conducted to identify the factors that affect the total score for subjective distress symptoms. Result: An association was shown between welding type (argon or non-argon welding) and the total score for subjective distress symptoms. Among the rate of complaining of subjective distress symptoms, vomiting and nausea, difficulty breathing, and allergic reactions were all significantly higher in the argon welding group. Only the concentration of dust and welding fumes was shown to be distributed normally after natural log transformation. According to logistic regression analysis, the correlations of working duration and welding type (argon or non-argon) between the total score of subjective distress symptoms were found to be statistically significant (p=0.041, p=0.049, respectively). Conclusion: Our results suggest that argon welding could cause subjective distress symptoms in shipyard workers.