• The Journal of the Korean dental association
• /
• v.55 no.2
• /
• pp.156-164
• /
• 2017

Purpose: The aim of this in vitro study was to assess changes in remineralization by stimulated human saliva over a short period of 48 hours with quantitative light-induced fluorescence (QLF) technology. Materials and Methods: Bovine incisor surfaces were demineralized for 10 days. Two types of stimulated saliva were collected from 7 healthy persons. 24 hours after tooth brushing (Stimulated saliva group) and immediately after tooth brushing with 1,000 ppm NaF dentifrice (Dentifrice saliva group). The specimens were immersed in saliva and fluorescence images were obtained by QLF-digital (QLF-D $biluminator^{TM}$,) at 2, 4, 6, 12, 24, and 48 hours fluorescence loss (${\Delta}F%$) of the lesions. A paired t-test was performed to assess fluorescence differences between before (${\Delta}F_{baseline}$) and after (${\Delta}F_{treatment\;time}$) the remineralization process. Results: Before the remineralization, the mean ${\Delta}F_{baseline}$ of the initial demineralized specimens was $-18.42{\pm}0.15$ (%). In both groups, the ${\Delta}F$ values obtained at baseline and after 2 hours were statistically significant (P < 0.001), indicating recovery of the lesions by approximately 40% after 2 hours. After 48 hours, remineralization rates were slightly higher (49%) for the stimulated saliva group than for the dentifrice saliva group (41%), but the difference was not statistically significant. Conclusions: With QLF minute degrees of remineralization by saliva can be measured in periods as short as 2 hours. Additionally no significantly higher effects of remineralization were observed in the dentifrice saliva group when compared to the stimulated saliva group.

• Economic and Environmental Geology
• /
• v.39 no.6 s.181
• /
• pp.753-770
• /
• 2006

In urban areas, groundwater pollution is heavily affected by urbanization with land use types. This study aims to characterize groundwater quality and contamination in Sasang industrial area of Busan Metropolitan City where metalworking, machinery and footwear factories are located. Busan Metropolitan City is the highest in the utilization of groundwater resources among the metropolitan cities in Korea. $K^+,\;Na^+,\;Ca^{2+},\;Mg^{2+},\;Cl^-,\;SO_4^{2-}\;and\;HCO_3^-$ concentrations, and electrical conductivity (EC), total dissolved solids (TDS) and salinity are high in the areas near the Nakdong River. The results are attributed to the influence of salt water which intruded into the coastal sediments during sedimentation. In addition, the dominant chemical type of Ca-Cl indicates the influence of salt water in the geological formations as well as anthropogenic pollution. $SiO_2$ ion is interpreted to originate from both water-silicate mineral reactions and the decomposition of cement concretes. Trichloroethylene (TCE) was detected at 12 sites of total 18 sites. However, tetrachloroethylene (PCE) was detected at f sites and 1.1.1-trichloroethane (TCA) at 3 sites. According to the factor analysis, factor 1 was explained by 49.8%, factor 2 19.8%, and factor 3 11.0% with total 80.6% explanation. pH, TDS, salinity, $Ca^{2+},\;K^+,\;Mg^{2+},\;Na^+,\;Al^{3+},\;As^{3+},\;Cl^-\;and\;Fe^{2+}$ were positively highly loaded to factor 1. The chemical components loaded to factor 1 represent the chemical characteristics of both industrial pollution and influence by salt water. Based on the cluster analysis and distribution pattern of chemical components, the concentration of $Na^+,\;Ca^{2+},\;Cl^-,\;SO_4^{2-}\;K^+,\;and\;Mg^{2+}$ is high in the riverside area of the Nakdong River composed of coastal sediments that is influenced by salt water. The downstream area of the Hakjang Stream is judged to be affected by both salt water and artificial pollution. The other part of the study area is interpreted by anthropogenic pollution.

• Archives of Pharmacal Research
• /
• v.20 no.3
• /
• pp.253-258
• /
• 1997

Ten, heretofore unreported, $ 5^I-methyl-5^I-[2-(5-substituted uracil-1-yl)ethyl)]-2^I-oxo-3^I$-methylenetetrahydrofurans (H, F, Cl, Br, I, $ CH_3$,$CF_3$,$CH_2CH_3$,$ CH=CH2$, SePh) (7a-j) were synthesized and evaluated against four cell lines (K-562, FM-3A, P-388 and U-937). For the preparation of ${\alpha}$-methylene-${\gamma}$-butyrolactone-linked to 5-substituted uracils (7a-j), the convenient Reformasky type reaction was employed which involves the treatment of ethyl ${\alpha}$-(bromomethyl)acrylate and zinc with the respective 1-(5-substituted uracil-1-yl)-3-butanone (6a-j). The 5-substituted uracil ketones (6a-j) were directly obtained by the respective Michael type reaction of vinyl methyl ketone with the $K_2CO_3$(or NaH)-treated 5-substituted uracils (5a-j) in the presence of acetic acid in the DMF solvent. The .alpha.-methylene-.gamma.-butyrolactone compounds showing the most significant antitumor activity are 7e, 7f, 7h and 7j (inhibitory concentration $(IC_50)$ ranging from 0.69 to $2.9 {\mu}g/ml$), while 7b, 7g and 7i have shown moderate to significant activity. The compounds 7a, 7c and 7d were found to be inactive. The synthetic intermediate compounds 6a-j were also screened and found marginal to moderate activity where compounds 6b and 6g showed significant activity $(IC_50:0.4~2.8 {\mu}g/ml)$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.399-399
• /
• 2013

Metal silicides는 Si 기반의microelectronic devices의 interconnect와 contact 물질 등에 사용하기 위하여 그 형성 mechanism과 전기적 특성에 대한 연구가 많이 이루어지고 있다. 이 중 Rare-earth(RE) silicides는 저온에서 silicides를 형성하고, n-type Si과 낮은 Schottky Barrier contact (~0.3 eV)을 이룬다. 또한 낮은 resistivity와 Si과의 작은 lattice mismatch, 그리고 epitaxial growth의 가능성, 높은 thermal stability 등의 장점을 갖고 있다. RE silicides 중 ytterbium silicide는 가장 낮은 electric work function을 갖고 있어 n-channel schottky barrier MOSFETs의 source/drain으로 주목받고 있다. 또한 Silicon 기반의 CMOSFETs의 성능 향상 한계로 인하여 germanium 기반의 소자에 대한 연구가 이루어져 왔다. Ge 기반 FETs 제작을 위해서는 낮은 source/drain series/contact resistances의 contact을 형성해야 한다. 본 연구에서는 저접촉 저항 contact material로서 ytterbium germanide의 가능성에 대해 고찰하고자 하였다. HRTEM과 EDS를 이용하여 ytterbium germanide의 미세구조 분석과 면저항 및 Schottky Barrier Heights 등의 전기적 특성 분석을 진행하였다. Low doped n-type Ge (100) wafer를 1%의 hydrofluoric (HF) acid solution에 세정하여 native oxide layer를 제거하고, 고진공에서 RF sputtering 법을 이용하여 ytterbium 30 nm를 먼저 증착하고, 그 위에 ytterbium의 oxidation을 방지하기 위한 capping layer로 100 nm 두께의 TiN을 증착하였다. 증착 후, rapid thermal anneal (RTA)을 이용하여 N2 분위기에서 $300{\sim}700^{\circ}C$에서 각각 1분간 열처리하여 ytterbium germanides를 형성하였다. Ytterbium germanide의 미세구조 분석은 transmission electron microscopy (JEM-2100F)을 이용하였다. 면 저항 측정을 위해 sulfuric acid와 hydrogen peroxide solution (H2SO4:H2O2=6:1)에서 strip을 진행하여 TiN과 unreacted Yb을 제거하였고, 4-point probe를 통하여 측정하였다. Yb germanides의 면저항은 열처리 온도 증가에 따라 감소하다 증가하는 경향을 보이고, $400{\sim}500^{\circ}C$에서 가장 작은 면저항을 나타내었다. HRTEM 분석 결과, deposition 과정에서 Yb과 Si의 intermixing이 일어나 amorphous layer가 존재하였고, 열처리 온도가 증가하면서 diffusion이 더 활발히 일어나 amorphous layer의 두께가 증가하였다. $350^{\circ}C$ 열처리 샘플에서 germanide/Ge interface에서 epitaxial 구조의 crystalline Yb germanide가 형성되었고, EDS 측정 및 diffraction pattern을 통하여 안정상인 YbGe2-X phase임을 확인하였다. 이러한 epitaxial growth는 면저항의 감소를 가져왔으며, 열처리 온도가 증가하면서 epitaxial layer가 증가하다가 고온에서 polycrystalline 구조의 Yb germanide가 형성되어 면저항의 증가를 가져왔다. Schottky Barrier Heights 측정 결과 또한 면저항 경향과 동일하게 열처리 증가에 따라 감소하다가 고온에서 다시 증가하였다.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.494-498
• /
• 2012

Geopolymer cements and geopolymer resins are newly advanced mineral binders that are used in order to reduce the carbon dioxide generation that accompanies cement production. The effect of additives on the compressive strength of geopolymerized class-F fly ash was investigated. Blast furnace slag, calcium hydroxide($Ca(OH)_2$), and silica fume powders were added to fly ash. A geopolymeric reaction was initiated by adding a solution of water glass and sodium hydroxide(NaOH) to the powder mixtures. The compressive strength of pure fly ash cured at room temperature for 28 days was found to be as low as 291 $kgf/cm^{-2}$, which was not a suitable value for use in engineering materials. On the contrary, addition of 20 wt% and 40 wt% of blast furnace slag powders to fly ash increased the compressive strength to 458 $kgf/cm^{-2}$ and 750 $kgf/cm^{-2}$, respectively. 5 wt% addition of $Ca(OH)_2$ increased the compressive strength up to 640 $kgf/cm^{-2}$; further addition of $Ca(OH)_2$ further increased the compressive strength. When 2 wt% of silica fume was added, the compressive strength increased to 577 $kgf/cm^{-2}$; the maximum strength was obtained at 6 wt% addition of silica fume. It was confirmed that the addition of CaO and $SiO_2$ to the fly ash powders was effective at increasing the compressive strength of geopolymerized fly ash.

• Journal of Radiation Protection and Research
• /
• v.41 no.2
• /
• pp.81-86
• /
• 2016

Background: For positron emission tomography (PET) application, cadmium zinc telluride (CZT) has been investigated by several institutes to replace detectors from a conventional system using photomultipliers or Silicon-photomultipliers (SiPMs). The spatial and energy resolution in using CZT can be superior to current scintillator-based state-of-the-art PET detectors. CZT has been under development for several years at the Korea Atomic Energy Research Institute (KAERI) to provide a high performance gamma ray detection, which needs a single crystallinity, a good uniformity, a high stopping power, and a wide band gap. Materials and Methods: Before applying our own grown CZT detectors in the prototype PET system, we investigated preliminary research with a developed discrete type data acquisition (DAQ) system for coincident events at 128 anode pixels and two common cathodes of two CZT detectors from Redlen. Each detector has a $19.4{\times}19.4{\times}6mm^3$ volume size with a 2.2 mm anode pixel pitch. Discrete amplifiers consist of a preamplifier with a gain of $8mV{\cdot}fC^{-1}$ and noise of 55 equivalent noise charge (ENC), a $CR-RC^4$ shaping amplifier with a $5{\mu}s$ peak time, and an analog-to-digital converter (ADC) driver. The DAQ system has 65 mega-sample per second flash ADC, a self and external trigger, and a USB 3.0 interface. Results and Discussion: Characteristics such as the current-to-voltage curve, energy resolution, and electron mobility life-time products for CZT detectors are investigated. In addition, preliminary results of gamma ray imaging using 511 keV of a $^{22}Na$ gamma ray source were obtained. Conclusion: In this study, the DAQ system with a CZT radiation sensor was successfully developed and a PET image was acquired by two sets of the developed DAQ system.

• Archives of Pharmacal Research
• /
• v.21 no.4
• /
• pp.458-464
• /
• 1998

Search for a new $\alpha$-methylene-$\gamma$-butyrolactone-bearing 6-substituted purine as a potental antitumor agent has led to synthesize seven, hitherto unreported, $5^1$-Methyl-$5^1$-[(6-substituted-9H-purin-9-yl)methyl]-$2^1$-oxo-$3^1$- methylenetetrahydrofurans (H, Cl, l, $CH_3$, $NH_2$, SH, >C=O) (6a-g). These include $5^1$-Methyl-$5^1$-[(9H-purin-9-yl)methyll-$2^1$-oxo-$3^1$ -methylenetetrahydrofurans (6a), $5^1$-Methyl-$5^1$-[(6-chloro-9H-purin-9-yl)methyl]-$2^1$-oxo-$3^1$-methylenetetrahydr ofurans (6b), $5^1$-Methyl-$5^1$-[(6-chloro-9H-purin-9-yl) methyl]-$2^1$-oxo-$3^1$-methylenetetrahydrofurans (6c), $5^1$-Methyl-$5^1$-[(6-methyl-9H-purin-9-yl) methyl]-$2^1$-oxo-$3^1$-methylenetetrahydrofurans (6d), $5^1$-Methyl-$5^1$-[(9H-adenin-9-yl)methyll-$2^1$-oxo-$3^1$-methylenetetrahydrofurans (6e), $5^1$-Methyl-$5^1$-[(6-mercapto-9H-purin-9-yl) methyl]-$2^1$-oxo-$3^1$-methylenetetrahydrofurans (6f) and $5^1$-Methyl-$5^1$-[(9H-hypoxanthin-9-yl)methyll-$2^1$-oxo-$3^1$-methylenetetrahydrof urans (6g) which were made by the Reformatsky-type reaction of ethyl $\alpha$-(bromomethyl) acrylate with the corresponding (6-substituted-9H-purin-9-yl)-2-propanone intermediates (5a-g). These ketone intermediates 5a-g, 1-(9H-purin-9-yl)-2-propanone (5a), 1-(6-chloro-9H-purin-9-yl)-2-propanone (5b), 1-(6-iodo-9H-purin-9-yi)-2-propanone (5c), 1-(6-methyl-9H-purin-9-yl)-2-propanone (5d), 1-(9H-adenin-9-yl)-2-propanone (Se), 1-(6-mercapto-9H-purin-9-yl)-2-propanone (5f), and 1-(9H-hypoxanthin-9-yl)-2-propanone (5g) were directly obtained by the alkylation of the 6-substituted purine bases with the chloroacetone in the presence of $K_2$$CO_3$ (or NaH) under DMF (or DMSO). The preliminary in vitro cytotoxcity assay for the synthetic .alpha.-methylene-y-butyro-lactone compounds (6a-g) were determined against three cell lines (PM-3A, P-388, and K-562) and showed the moderate antitumor activity ($IC_50$ ranged from 1.4 to 4.3 $\mu\textrm{g}$/ml) with the compound $5^1$-methyl-$5^1$ -[(9H-hypoxanthin-9-yl)methyl]-$2^1$-oxo-$3^1$-methylenetetrahydrofuran (6g) showing the least antitumor activity.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.452-460
• /
• 2007

Ultra-low loss ZERODUR and fused silica mirrors were manufactured and their light scattering characteristics were investigated. For this purpose, ZERODUR and fused silica substrates were super-polished by the bowl feed method. The surface roughness were 0.292 ${\AA}$ and 0.326 ${\AA}$ in rms for ZERODUR and fused silica, respectively. To obtain the high reflectivity, 22 thin film layers of $SiO_2$ and $Ta_2O_5$ were deposited by Ion Beam Sputtering. The measured light scattering of ZERODUR and fused silica mirror were 30.9 ppm and 4.6 ppm, respectively. This shows that the substrate surface roughness is not the only parameter which determines the light scattering of the mirror. In order to investigate the mechanism for additional light scattering of the ZERODUR mirror, the surface roughness of the mirror was measured by AFM and was found to be 2.3 times higher than that of the fused silica mirror. It is believed that there is some mismatch at the interface between the substrate and the first thin film layer which leads to the increased mirror surface roughness. To clarify this, the contact angle measurements were performed by SEO 300A, based on the Giriflaco-Good-Fowkes-Young method. The fused silica substrates with 0.46 ${\AA}$ in its physical surface roughness shows lower contact angle than that of the ZERODUR substrate with 0.31 ${\AA}$. This indicates that the thin film surface roughness is determined by not only its surface roughness but also the surface energy of the substrate, which depends on the chemical composition or crystalline orientation of the materials. The surface energy of each substrate was calculated from a contact angle measurement, and it shows that the higher the surface energy of the substrate, the better the surface roughness of the thin film.

• Journal of Marine Bioscience and Biotechnology
• /
• v.2 no.3
• /
• pp.174-186
• /
• 2007

Amphora coffeaeformis and Achnanthes longipes are commonly found as dominant benthic microalgae in Jeju coastal water throughout the year. In order to investigate pharmaceutical uses of these diatoms, each single species was isolated with micropipette under phase contrast microscope and subcultured with synthetic seawater media which was enriched with F/2 media, trace metal solution and $Na_2SiO_3$). Growth characteristics of these species were also determined with different combination of salinity, nutrients concentration and temperature. Thereafter, mass culture of each species was done based on the maximum growth condition. Biomass was collected after two weeks of mass culture and freeze dried for antioxidant study. The antioxidant properties of different fractions (n-hexane, chloroform and ethylacetate) obtained by solvent fractionation of 80% methanolic extract of two microalgae were investigated for free radical, reactive oxygen species scavenging (Super oxide, Hydrogen peroxide, Hydroxyl radical and Nitric oxide), metal chelating and lipid peroxidation inhibition activities. All fractions of A. longipes showed higher $DPPH^{\cdot}$ (free radical) scavenging activities (n-hexane: 89.0%, Chloroform: 76.0%, Ethylacetate: 66.0%, Methanol: 90.6% and aqueous residue: 63.0%). N-hexane fraction of A. longipes showed significantly higher activity (49.0%) on nitric-oxide. Ethylacetate fraction of A. longipes and aqueous residue of A. coffeaeformis exhibited 64.0% and 75.6% metal chelating activity which was higher than commercial antioxidants (${\alpha}$-tocopherol: 18.0% and BHT: 16.0%). The n-hexane fraction of A. coffeaeformis had 67.5% activity on $DPPH^{\cdot}$. Chloroform and n-hexane fractions of A. coffeaeformis exhibited 46.2% and 47.6% $H_2O_2$ scavenging effects which were closely similar to commercial antioxidants (${\alpha}$-tocopherol: 49.2% and BHT: 58.6%). Chloroform and ethylacetate fractions of A. longipes and fraction of n-hexane and chloroform of A. coffeaeformis showed better lipid peroxidation activities than ${\alpha}$-tocopherol. These data suggest that both organic and aqueous fractions have good antioxidative compounds with different antioxidant properties.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1638-1643
• /
• 2018

Multi-layer ceramic capacitors as decoupling capacitor were fabricated by dielectric composition with a high dielectric constant. The fabricated decoupling capacitors were embedded in the PCB of the 10G RF transceiver module and evaluated for the characteristics of electrical noise by the level of AC input voltage. In order to further improve the electrical properties of the $BaTiO_3$ based composite, glass frit, MgO, $Y_2O_3$, $Mn_3O$, $V_2O_5$, $BaCO_3$, $SiO_2$, and $Al_2O_3$ were used as additives. The electrical properties of the composites were determined by various amounts of additives and optimum sintering temperature. As a result of the optimized composite, it was possible to obtain a density of $5.77g/cm^3$, a dielectric constant of 1994, and an insulation resistance of $2.91{\times}10^{12}{\Omega}$ at an additive content of 5wt% and a sintering temperature of $1250^{\circ}C$. After forming a $2.5{\mu}m$ green sheet using the doctor blade method, a total of 77 layers were laminated and sintered at $1180^{\circ}C$. A decoupling capacitor with a size of $0.6mm(W){\times}0.3mm(L){\times}0.3mm(T)$ (width, length and thickness, respectively) and a capacitance of 100 nF was embedded using a PCB process for the 10G RF Transceiver modules. In the range of AC input voltage 400mmV @ 500kHz to 2200mV @ 900kHz, the embedded 10G RF Transceiver modules evaluated that it has better electrical performance than the non-embedded modules.