• The Korean Journal of Pesticide Science
• /
• v.4 no.1
• /
• pp.1-10
• /
• 2000

The purpose of this study is to establish the assessment techniques of hazardous chemicals by the development of analytical method of biological samples. In this study, we have developed an extraction method of nine pesticides used for rice paddy that resulted in high recovery from the spiked human urine by the liquid-liquid extraction with diethyl ether at pH 7.0. Calibration curve obtained from each pesticide standard using by gas chromatography/mass spectrometry/selected ion monitoring has shown good linearity and detection limits were the range of $0.4{\sim}2.0$ ng/mL in urine. As a biological monitoring, urine samples of local farmers exposed directly to nine pesticides in the field were collected and analyzed by GC/MS. Of the tested pesticides, metabolites of phenthoate assumed were identified by GC/MS analysis. No parent compound was detected.

• Analytical Science and Technology
• /
• v.24 no.2
• /
• pp.142-149
• /
• 2011

This study was conducted to define metabolite of the resveratrol by gas chromatography- time-offlight mass spectrometric detection. From these results, we suppose that the structure of metabolite is the result of reduction of double-bond attached by two-phenyl groups. Also, validity of method for determining metabolite of resveratrol and endogenous steroids was tested. The recoveries ranged from 96.47 to 114.74%, and intraand inter-day precision ranged 11.40 - 10.87% and 1.10 - 10.93%, accuracy ranged 80.03 - 119.92% and 80.02 - 119.56%, respectively. Resveratrol and endogenous steroids had correlation coefficients above or equal to 0.996. The method was successfully validated for the determination of resveratrol and endogenous steroids. Urinary samples from volunteers dosed resveratrol were analyzed to confirm a correlation resveratrol and its metabolite. From these results, the highest level of resveratrol and its metabolite was excreted in 10 - 15 hr more slowly than common drug, and conversion rate of metabolite was higher in woman than that in man. In addition, endogenous steroids were shown same the highest level of 10 - 15 hr. For estrone and estradiol, sensitivity was relatively higher in female than in man. And there were no significant changes of excretion patterns in the other endogenous steroids. Thus, we assumed that activation of resveratrol has impact on woman than man.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.18 no.2
• /
• pp.160-166
• /
• 1989

This study was conducted to investigate whether egg-shell may be used as a mineral sourceor leavening agent in breadmaking. In Korea the waste volume of egg shell has been estimated at about 28,694 tons per year. Carbon dioxide generation maxima were established for barking powder$(153{\pm}3ml/g)$, egg-shell(205in reaction with lactic acid) and yeast$(115{\pm}3ml/sugar\;g)$. Gas release time required for each substance to reach $CO_2$ maximum was, for baking powder 7 minutes, for egg-shell 45 mins and for yeast 240 mins. Particle size of egg-shell in breadmaking was suitable more than 20 mesh (-). When egg-shell only was added to the basic formular without including lactic acid, no leavening effect was observed. However, when lactic acid and egg-shell were used together, the leavening effect was more or less equivalent to that of yeast(control). Addition of egg-shell was found to increase calcium content of bread products without noticeable altering flavor, as compared with control. Joint use of egg-shell was organic acids in breadmaking was shown to have potential in time saving, volume increase and yeast saving.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.11
• /
• pp.6261-6265
• /
• 2013

Background: Recent studies have suggested that expression of the RAS protein activator like-1 gene (RASAL1) is decreased in gastric carcinoma tissues and cell lines, indicated a role in tumorigenesis and development of gastric cancer. Reduced expression of RASAL1 could result in aberrant increase of activity of RAS signaling pathways in cancer cells. However, the exact mechanism which induces down-regulation of the RASAL1 gene remains unclear. This study aimed to determine the methylation status and regulation of RASAL1 in gastric cancer. Materials and Methods: Using the methylation-specific polymerase chain reaction (MSP), the methylation status of CpG islands in the RASAL1 promoter in gastric cancers and paired adjacent non-cancerous tissues from 40 patients was assessed and its clinicopathological significance was analyzed. The methylation status of RASAL1 in gastric cancer lines MKN-28, SGC-790l, BGC-823, as well as in normal gastric epithelial cell line GES-l was also determined after treatment with a DNA methyltransferase inhibitor, 5-aza-2'-doexycytidine (5-Aza-CdR). RAS activity (GAS-GTP) was assessed through a pull-down method, while protein levels of ERK1/2, a downstream molecule of RAS signaling pathways, were determined by Western blotting. Results: The frequencies of RASAL1 promoter methylation in gastric cancer and paired adjacent non-cancerous tissues were 70% (28/40) and 30% (12/40) respectively (P<0.05). There were significantly correlations between RASAL1 promoter methylation with tumor differentiation, tumor size, invasive depth and lymph node metastasis in patients with gastric cancer (all P<0.05), but no correlation was found for age or gender. Promoter hypermethylation of the RASAL1 gene was detected in MKN-28, SGC-790l and BGC-823 cancer cells, but not in the normal gastric epithelial cell line GES-1. Elevated expression of the RASAL1 protein, a decreased RAS-GTP and p-ERK1/2 protein were detected in three gastric cancer cell lines after treatment with 5-Aza-CdR. Conclusions: Aberrant hypermethylation of the RASAL1 gene promoter frequently occurs in gastric cancer tissues and cells. In addition, the demethylating agent 5-Aza-CdR can reverse the hypermethylation of RASAL1 gene and up-regulate the expression of RASAL1 significantly in gastric cancer cells in vivo. Our study suggests that RASAL1 promoter methylation may have a certain relationship with the reduced RASAL1 expression in gastric cancer.

• Asian Journal of Atmospheric Environment
• /
• v.6 no.4
• /
• pp.288-303
• /
• 2012

In this study, real time measurements of particle number size distribution in urban Gwangju, coastal Taean, and industrial Yeosu in Korea were conducted in 2008 to understand the occurrence of ultrafine particle (UFP) (<100 nm) events, the variation of its concentration among different sampling sites, and UFP formation pathways. Also, to investigate seasonal and long-term variation of the UFP number concentration, data were collected for the period of 5 years (2007, 2008, 2010, 2011, and 2012) in urban Gwangju. Photochemical and combustion events were found to be responsible for the formation of UFP in the urban Gwangju site, whereas only photochemical event led to the formation of UFP in the coastal Taean site. The highest UFP concentration was found in industrial Yeosu (the average UFP number fractions were 79, 59 and 58% in Yeosu, Gwangju, and Taean, respectively), suggesting that high amount of gas pollutants (e.g., $NO_2$, $SO_2$, and volatile organic carbon (VOC)) emitted from industries and their photochemical reaction contributed for the elevated UFP concentration in the industrial Yeosu site. The UFP fraction also showed a seasonal variation with the peak value in spring (61.5, 54.5, 50.5, and 40.7% in spring, fall, summer, and winter, respectively) at urban Gwangju. Annual average UFP number concentrations in urban Gwangju were $5.53{\times}10^3\;cm^{-3}$, $4.68{\times}10^3\;cm^{-3}$, $5.32{\times}10^3\;cm^{-3}$, $3.99{\times}10^3\;cm^{-3}$, and $2.16{\times}10^3\;cm^{-3}$ in the year 2007, 2008, 2010, 2011, and 2012, respectively. Comparison of the annual average UFP number concentration with urban sites in other countries showed that the UFP concentrations of the Korean sites were lower than those in other urban cities, probably due to lower source strength in the current site. TEM/EDS analysis for the size-selected UFPs showed that the UFPs were classified into various types having different chemical species. Carbonaceous particles were observed in both combustion (soot and organics) and photochemical events (sulfate and organics). In the photochemical event, an internal mixture of organic species and ammonium sulfate/bisulfate was identified. Also, internal mixtures of aged Na-rich and organic species, aged Ca-rich particles, and doughnut shaped K-containing particles with elemental composition of a strong C with minor O, S, and K-likely to be originated from biomass burning nearby agricultural area, were observed. In addition, fly ash particles were also observed in the combustion event, not in the photochemical event.

• Korean Journal of Veterinary Research
• /
• v.47 no.1
• /
• pp.103-115
• /
• 2007

The aim of this study was to compare the reaction of the cardiovascular system, and the anesthetic effect among 3 experimental groups, epidural administration of medetomidine as a single agent, the combination of buprenorphine and medetomidine, and the combination of fentanyl and medetomidine. Twenty one dogs were anesthetized with isoflurane and allowed to breathe spontaneously. Epidural, arterial, and venous catheters were inserted. The tip of epidural catheter was positioned at the level of the space between the sixth and seventh lumbar vertebra. After a stable plane of anesthesia was achieved, these dogs were each administered one of the following treatments epidurally : medetomidine $10{\mu}g/kg$ (Group M), a combination of medetomidine $5{\mu}g/kg$ and buprenorphine $10{\mu}g/kg$ (Group M/B), and a combination of medetomidine $5{\mu}g/kg$ and fentanyl $10{\mu}g/kg$ (Group M/F). Heart rate (HR), Respiratory rate (RR), End-tidal carbon dioxide (EtCO2), and arterial blood pressure were measured before drug administration (base line) and 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, and 60 min postinjection. Blood gas analysis was performed before injection and 5, 15, 25, 35, 45, 60 min postinjection. Isoflurane was discontinued 80 min postinjection and pain/motor function were evaluated up to 260 min postinjection every 15 min. At the early stage of drug introduction (until 5 min), the HR was decreased significantly in all 3 groups compared with base line. In Group M, HR was significantly decreased compared with the other 2 groups. With time (starting 20 min after drug introduction), the HR was decreased significantly in Group M/B in respect to base line. However, no significant difference was seen number-wise in all 3 groups. During 60 min after drug introduction, the systolic, diastolic and mean arterial pressures were highest in Group M and lowest in Group M/F. Among 3 groups, drug action and motor loss duration were longest in Group M/F. Analgesic effect observed in the M/F group was the most prominent and long-lasting, compared to those seen in the other 2 groups. Given the fact that the recovery of motor function takes place in a short period of time after analgesic effects disappeared, additional use of M/F depending on the patient's condition would be a good way to achieve effective pain management. However, proper care should be taken to ensure the function of cardiovascular system in the patient because the administration of M/F under isoflurane anesthesia results in a significant decline in arterial blood pressure ($65{\pm}10mmHg$).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.146-147
• /
• 2011

Processing a large area substrate for liquid crystal display (LCD) or solar panel applications in a capacitively coupled plasma (CCP) reactor is becoming increasingly challenging because of the size of the substrate size is no longer negligible compared to the wavelength of the applied radio frequency (RF) power. The situation is even worse when the driving frequency is increased to the Very High Frequency (VHF) range. When the substrate size is still smaller than 1/8 of the wavelength, one can obtain reasonably uniform process results by utilizing with methods such as tailoring the precursor gas distribution by adjustingthrough shower head hole distribution or hole size modification, locally adjusting the distance between the substrate and the electrode, and shaping shower head holes to modulate the hollow cathode effect modifying theand plasma density distribution by shaping shower head holes to adjust the follow cathode effect. At higher frequencies, such as 40 MHz for Gen 8.5 (2.2 m${\times}$2.6 m substrate), these methods are not effective, because the substrate is large enough that first node of the standing wave appears within the substrate. In such a case, the plasma discharge cannot be sustained at the node and results in an extremely non-uniform process. At Applied Materials, we have studied several methods of modifying the standing wave pattern to adjusting improve process non-uniformity for a Gen 8.5 size CCP reactor operating in the VHF range. First, we used magnetic materials (ferrite) to modify wave propagation. We placed ferrite blocks along two opposing edges of the powered electrode. This changes the boundary condition for electro-magnetic waves, and as a result, the standing wave pattern is significantly stretched towards the ferrite lined edges. In conjunction with a phase modulation technique, we have seen improvement in process uniformity. Another method involves feeding 40 MHz from four feed points near the four corners of the electrode. The phase between each feed points are dynamically adjusted to modify the resulting interference pattern, which in turn modulate the plasma distribution in time and affect the process uniformity. We achieved process uniformity of <20% with this method. A third method involves using two frequencies. In this case 40 MHz is used in a supplementary manner to improve the performance of 13 MHz process. Even at 13 MHz, the RF electric field falls off around the corners and edges on a Gen 8.5 substrate. Although, the conventional methods mentioned above improve the uniformity, they have limitations, and they cannot compensate especially as the applied power is increased, which causes the wavelength becomes shorter. 40 MHz is used to overcome such limitations. 13 MHz is applied at the center, and 40 MHz at the four corners. By modulating the interference between the signals from the four feed points, we found that 40 MHz power is preferentially channeled towards the edges and corners. We will discuss an innovative method of controlling 40 MHz to achieve this effect.

• Fire Science and Engineering
• /
• v.28 no.5
• /
• pp.71-79
• /
• 2014

This study was performed to test the combustive properties of Medium Density Fibreboards (MDFs) treated with chemicals of the bis-(dimethylaminomethyl) phosphinic acid (DMDAP), N,N-dimethylethylenediaminomethyl-bis-phosphonic acid (DMDEDAP), piperazinomethyl-bis-phosphonic acid (PIPEABP), and methylpiperazinomethyl-bis-phosphonic acid (MPIPEABP). MDFs were painted in three times with 15 wt% solution of the bis-(dimethylaminomethyl) phosphinic acid and alkylenediaminoalkyl-bis-phosphonic acids at the room temperature, respectively. After drying MDF treated with chemicals, combustive properties and volatile organic compounds (VOCs) contents were examined by the cone calorimeter (ISO 5660-1), test for flame retardant (NEMA Notice No. 2012034), and gas chromatography (KS M ISO 11890-2), respectively. It was indicated that the MDFs treated with chemicals showed the longer time to combustion time (CT) = (442~492) s than that of virgin plate by reducing the burning rate except for CT treated with DMDAP. In adition, the MDFs treated with chemicals showed both of the higher char area (44.33~61.33) kg/kg and char length (10.33~11.67) cm than those of virgin plate. Especially, the MDFs treated with chemicals showed the higher mean volatile organic compounds (VOCs) (0.188~0.333) g/L than that of virgin plate within the prescribed limits. Thus, It is supposed that the combustion- retardation properties were improved by the partial due to the treated chemicals in the virgin MDF.

• Land and Housing Review
• /
• v.8 no.3
• /
• pp.189-200
• /
• 2017

The work breakdown structure and the precedence relations by work activity are very important because they are the basic data for estimating the construction duration in the construction work. However, there is no standard to accurately estimate the construction duration since the size of the school facilities construction is smaller than the general construction work. Therefore, some schools are unable to open in March or September and the delay of the construction duration can cause damage to the students. To solve this problem, this study developed a work breakdown structure of school facilities construction work and analyzed the precedence relations by work activities. The work breakdown structure of the school facilities construction is composed of three steps. The operations corresponding to level 1 and level 2 are as follows. (1) 2 preparatory work categories; preparation period and temporary construction. (2) 17 architectural work categories; temporary construction, foundation & pile work, reinforced concrete work, steel roof work, brick work, plaster work, tile work, stone work, waterproof construction, wood work, interior construction, floor work, metal work, roof work, windows construction, glazing work and paint construction. (3) 7 mechanic and fire work categories; outside trunk line work, plumbing work, air-conditioning equipment work, machine room work, city gas plumbing work, sanitation facilities and inspection & test working. (4) 4 civil work categories; wastewater work, drainage work, pavement work and other work. (5) 1 landscaping work categories; planting work. The work breakdown structure was derived from interviews with experts based on the milestones and detailed statements of existing school facilities. The analysis of precedence relations by school facilities work activity utilized PDM(Precedence Diagramming Method)which does not need a dummy and the relations were applied using FS(Finish to Start), FF(Finish to Finish), SS(Start to Start), SF(Start to Finish). The analysis of this study shows that if one work activity is delayed, the entire construction duration may be delayed because the majority of the works are FS relations. Therefore, it is necessary to use the Lag at the appropriate time to estimate the standard construction duration of the school facility construction. Lag is a term used only in the PDM method and it is used to define the relationship between the predecessor and the successor in creating the network milestone. And it means the delay time applied to the two work activities. The results of this study can reasonably estimate the standard construction duration of school facilities and it will contribute to the quality of the school facilities construction.

• Korean Journal of Food Science and Technology
• /
• v.32 no.5
• /
• pp.1029-1034
• /
• 2000

A suitable method of sample treatments to minimize the analytical interferences was presented in order to determine bisphenols [bisphenol F (BPF), bisphenol A (BPA), bisphenol F diglycidyl ether (BFDGE), and bisphenol A diglycidyl ether (BADGE)] in various canned beverages coated with epoxy resin by the reversephase high performance liquid chromatography (RP-HPLC) equipped with a fluorescence detector and the gas chromatography with mass selective detection. The recovery test of bisphenols was performed using 1, 5, and 10 ${\mu}g/L$ bisphenols spiked beverages with the combined technique of the solid-phase extraction (SPE) and the liquid-phase extraction (LPE). Both BPA and BADGE showed quite adequate resolutions in HPLC-chromatograms. The recoveries of BPA obtained by LPE with diethyl ether were higher than those obtaind with methylene chloride on coffee, shikhye and fruit juice. For cola and tea, the recoveries of BPA obtaind by SPE were higher than those by LPE with diethyl ether. The recoveries of BADGE were less than those of BPA for all beverage samples treated by either SPE or LPE method. In survey of bisphenols for eighteen commercial canned beverage samples, BPA contents of coffee, cola, tea, shikhye, and fruit juice were in the range of $1.3{\sim}11.6,\;0.5{\sim}0.9,\;1.0{\sim}1.3,\;2.4{\sim}7.9$, and $3.0{\sim}3.4\;{\mu}g/L$, respectively, but there was no detection of BPA in beer sample.