• Transactions on Electrical and Electronic Materials
• /
• 제11권6호
• /
• pp.261-265
• /
• 2010

In this paper, we attempt to improve the electrical characteristics of epoxy resin at high temperature (above $80^{\circ}C$) by adding magnesium oxide (MgO), which has high thermal conductivity. Scanning electron microscopy (SEM) of the dispersion of specimens with added MgO reveals that they are evenly dispersed without concentration. The dielectric breakdown characteristics of $SiO_2$ and MgO nanocomposites are tested by measurements at different temperatures to investigate the filler's effect on the dielectric breakdown characteristics. The dielectric breakdown strength of specimens with added $SiO_2$ decreases slowly below $80^{\circ}C$ (low temperature) but decreases rapidly above $80^{\circ}C$ (high temperature). However, the gradient of the dielectric breakdown strength of specimens with added MgO is slow at both low and high temperatures. The dielectric breakdown strength of specimens with 0.4 wt% $SiO_2$ is the best among the specimens with added $SiO_2$, and that of specimens with 3.0 wt% and 5.0 wt% MgO is the best among those with added MgO. Moreover, the dielectric strength of specimens with 3.0 wt% MgO at high temperatures is approximately 53.3% higher than that of specimens with added $SiO_2$ at $100^{\circ}C$, and that of specimens with 5.0 wt% of MgO is approximately 59.34% higher under the same conditions. The dielectric strength of MgO is believed to be superior to that of $SiO_2$ owing to enhanced thermal radiation because the thermal conductivity rate of MgO (approximately 42 $W/m{\cdot}K$) is approximately 32 times higher than that of $SiO_2$ (approximately 1.3 $W/m{\cdot}K$). We also confirmed that the allowable breakdown strength of specimens with added MgO at $100^{\circ}C$ is within the error range when the breakdown probability of all specimens is 40%. A breakdown probability of up to 40% represents a stable dielectric strength in machinery and apparatus design.

• 한국주조공학회지
• /
• 제5권3호
• /
• pp.19-26
• /
• 1985

This study has been carried out to examine into wettability of Cu-5%Sn alloy in $Al_2O_3$, MgO, $SiO_2$ and graphite, respectively and investigated into the change in macrostructure of Cu-5%Sn alloy according to kind and mixing rate of mold-coating. The results obtained from the experiment are summerized as follows; 1. Cu Cu-5%Sn alloy, wettabilities of $Al_2O_3$ and MgO were good, on the other hand, wettabilities of $SiO_2$ and graphite were bad. 2. The fine equiaxed zone was created because of the role of $Al_2O_3$ and MgO as preferential nucleation sites. 3. Notwithstanding change of mixing rate of $SiO_2$ in mold coating the equixed zone was not created. 4. The area of equiaxed zone was varied according to mixing rate in the case of using $Al_2O_3$ and MgO in mold-coating.

• 농업과학연구
• /
• 제2권1호
• /
• pp.61-100
• /
• 1975

수도재배(水稻栽培)에 있어 작중토(作中土)의 유효규산함량(有效珪酸含量), ppm과 유기물함량(有機物含量)% 비(比) $SiO_2$/O.M. 근거(根據)한 N 적량(適量) 추정식(推定式) $Nkg/10a=(4.2+0.096\;SiO_2/O.M.).F$에서 N시비량(施肥量)을 추정(推定) 시용(施用)할 때의 적정(滴定) 가리(加里) 시용량(施用量) 추정식(推定式) $K_2Okg/10a=(K_O/\sqrt{Ca+Mg}-Ks/\sqrt{Ca+Mg})\sqrt{Ca+Mg}{\cdot}47{\cdot}BD$ 단 (但) $K_O/\sqrt{Ca+Mg}=0.03158+0.0007658\;SiO_2/O.M.$ $K_S/\sqrt{Ca+Mg}=Kme/100g/\sqrt{(Ca+Mg)}me/100g$의 타당성(妥當性) 여부(如否)를 판단(判斷)하기 위하여 3수준(水準)의 규회석처리(珪灰石處理)를 주구(主區)로하여 작토중(作土中)의 $SiO_2$/O.M. 비(比)를 증대(增大) 시키고 각주구별(各主區別)로 적정가리시용량(適正加里施用量) 추정식(推定式)에서 추정(推定)한 $K_2O$ 시용량(施用量)과 이에30%를 증비(增肥)하는구(區) 및 적정가리시용추정치(適正加里施用推定値)와는 관계(關係)없이 $K_2O\;8kg/10a$를 시용(施用)하는 3개수준(個水準)의 $K_2O$ 처리구(處理區)를 설정(設定)하여 수도품종(水稻品種) Akibare를 재배(栽培)하는 포장시험(圃場試驗)을 수행(遂行)하고 토양(土壤), 식물체분석(植物體分析) 및 수도(水稻)의 생육(生育)과 수량(收量) 및 수량구성요소(收量構成要素)들을 조사(調査)한 성적(成績)들을 종합검토(綜合檢討)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 작토중(作土中) 유효규산함량(有效珪酸含量) ppm과 유기물함량(有機物含量)%비(比), $SiO_2$/O.M.에 근거(根據)한 수도(水稻)에 대(對)한 N적량추정식(適量推定式)에서 추정(推定)한 N시용량(施用量)은 수도품종(水稻品種) Akibare의 생육(生育) 및 수량면(收量面)에서 볼 때 과량(過量)이었으며 토양(土壤) 및 식물체(植物體) 분석치(分析値)들에서 검토(檢討)한 결과(結果) $SiO_2$/O.M. 비조절(比調節)의 기본원리(基本原理)는 합당(合當)하나 그 식(式)의 상수(常數) 또는 F값은 변동(變動)되여야 한다고 판단(判斷)되였다. 2. 작토중(作土中)의 K활성도(活性度) 치환성(置換性) 염기 me/100 g비(比) $K/\sqrt{Ca+Mg}$를 조절(調節)하기 위한 $K_2O$ 시비량(施肥量) 추정식(推定式)에서 추정(推定)한 $K_2O$ 시용량(施用量)은 수도품종(水稻品種) Akibare의 생육(生育) 및 수량면(收量面)에서 과량(過量)이였으며 토양(土壤) 및 식물체(植物體) 분석치(分析値)들에서 검토(檢討)한 결과(結果) 조절기준(調節基準)되는 $K_O/\sqrt{Ca+Mg}$의 설정식(設定式) 즉(卽) $K_O/\sqrt{Ca+Mg}=0.03158+0.0007658\;SiO_2/O.M.$의 원리(原理)는 합리적(合理的)이나 기상수(其常數)의 변동(變動)이 필요(必要)하며 $K_S/\sqrt{Ca+Mg}$에 있어서도 토양(土壤)의 K공급능(供給能)을 고려(考慮)할수 있는 새로운 조절기준(調節基準)이 설정(設定)되어야 한다고 판단(判斷)되였다. 3. 수도(水滔)에 대한 $K_2O$ 시용량(施用量) 추정식중(推定式中)의 $K_S/\sqrt{Ca+Mg}$ 조절(調節) 기준(基準)은 K 공급능(供給能)을 대표(代表)할수 있는 작토중(作土中)의 치환성(置換性) Kme/100g에 근거(根據)해서 마음과 같이 설정(設定)함이 보다 합리적(合理的)임을 수도품종(水稻品種) Akibare의 천상수량 $K_2O$ 흡수량면(吸收量面)에서 밝힐수 있었다. 즉 $K_S/\sqrt{Ca+Mg}=0.037+0.78Kme/100g$.

• 자원리싸이클링
• /
• 제24권1호
• /
• pp.35-42
• /
• 2015

본 연구는 건식제련법으로 폐 PCB를 처리하는 공정에서 슬래그 중 Ni의 용해거동에 대한 기초연구로서, CaO-$SiO_2-Al_2O_3$-MgO계 슬래그와 Cu-5 wt%Ni합금 사이의 Ni 분배거동을 1623~1823 K의 $CO_2$-CO 분위기 중에서 조사하였다. 평형산소분압이 증가할수록 Ni의 분배비는 선형적으로 증가하였으며, 이 결과로부터 Ni의 슬래그 중 용해반응은 다음과 같이 나타낼 수 있다. $$Ni(l)_{metal}+\frac{1}{2}O_2(g)NiO(l)_{slag}$$ 슬래그 중 염기성 산화물(CaO와 MgO)의 농도가 증가할수록 Ni의 분배비는 선형적으로 증가하였다. 그러나 반응 온도가 높을수록 Ni의 분배비는 선형적으로 감소하였다. 이러한 결과로부터 Ni의 분배비에 미치는 실험변수의 영향을 다중 회귀분석하여 다음과 같은 경험식을 얻었다. $${\log}L_{Ni}=0.4000{\log}P_{O2}-5.1{\times}10^{-4}T+0.3375\(\frac{X_{CaO}+X_{MgO}}{X_{SiO2}}\)$$

• 공업화학
• /
• 제29권4호
• /
• pp.461-467
• /
• 2018

본 연구에서는 $(n-BuCp)_2ZrCl_2$를 $SiO_2/MgCl_2$ 이원 지지체에 담지시켰다. 촉매를 담지하기 전, $SiO_2/MgCl_2$ 이원 지지체를 3종의 알킬알루미늄 화합물, 트리메틸알루미늄, 트리에틸알루미늄 또는 에틸알루미늄 세스퀴클로라이드로 표면처리 하였다. 합성된 표면 처리된 $SiO_2/MgCl_2$에 담지된 메탈로센 촉매로 에틸렌 및 1-헥센의 공중합을 하였다. 촉매 특성 및 성능을 BET, XPS 분석, ICP-AES 분석 및 FE-SEM을 통해 비교 분석하였다. 생성된 공중합체를 DSC 분석, GPC 분석, 13C-NMR 분석 및 FE-SEM을 통해 비교 분석하였다. 합성된 $SiO_2/MgCl_2$ 담지된 메탈로센 촉매의 분석은 이들 촉매의 Zr 함량이 $SiO_2$에 담지된 촉매에 비해 상대적으로 낮다는 것을 보여 주었다. 이것은 재결정된 $MgCl_2$ 및 알킬알루미늄의 존재로 인한 $SiO_2$의 표면적 감소에 기인할 수 있다. 또한, $SiO_2/MgCl_2$ 담지된 메탈로센 촉매는 $SiO_2$에 담지된 메탈로센 촉매보다 활성이 높았으며 이 중 EASC-표면 처리 이원 지지체에 담지된 메탈로센촉매가 1.9 kg PE/($mmol-Zr^*hr$)의 가장 높은 활성을 보였다. 이것은 EASC가 강한 루이스 산으로 작용하기 때문이다. 또한, 사용된 알킬알루미늄의 리간드가 클수록 생성된 중합체의 입자 표면이 더 거칠었다.

• 한국전기전자재료학회논문지
• /
• 제23권2호
• /
• pp.118-123
• /
• 2010

The eco-friendly technologies have been extended as matter of international concern due to various diseases and syndromes according to an environmental pollution. In this study, we have manufactured a ceramic cluster with thick film type for anion generation equipment which is maximized anion but minimized ozone contents generated. To develop the formulation of ceramic cluster, we conducted the $Mg_2SiO_4$ powders doped with 10 vol% glass frits as Na-Zn-B-O system and sintered at $1050^{\circ}C$ for 2 hours in air for starting materials and investigated the matching properties between the Ag-Pd electrode and the starting materials. The sintered sample for the composition of cluster has 6.7 of dielectric constant and 32 kV/mm of withstand voltage. The yield of anions was measured according to an electrode pattering, discharge gap between electrode, and thickness of electrode protective layer in the cluster of thick film type. We have manufactured the ceramic clusters with optimized thick film structure that have an anion over a hundred particles and the ozone of 0.6 ppb generated.

• Journal of Welding and Joining
• /
• 제21권1호
• /
• pp.107-113
• /
• 2003

Joining of $Si_3N_4$ to $Si_3N_4$ with crystallized glass solder was studied. $SiO_2-Al_2O_3-MgO$ glass with $P_2O_5$ as a crystallizing reagent was used as a solder. To improve the hish temperature toughness of joined specimen, two stage heat treatment was applied to Joined sample for the crystallization of joined layer, Two factors, i.e. thickness of soldered layer and crystallization were taken and thier effects on joining strength were investigated by a SEM-EDX observation of joined interface and bending strength both at room and elevated temperatures. Obtained results are summarized as follows: (1) Nitrogen diffused from $Si_3N_4$ to solder during the Joining process. Average amount of nitrogen in soldered layer depended on the thickness of the soldered layer and increased with decrease of the thickness. (2) Joining strength of the specimen having a thinner soldered layer was stronger than that of thicker layer. This can be mainly attributed to the difference of the nitrogen content in the soldered layer. (3) Higher content of nitrogen in solder brought forth higher viscosity of the solder. Hence the crystallization of the solder become more difficult in thinner layer of the solder than thicker one. (4) Thus, the effect of crystallization was evaluated mostly by the thicker layer specimen. Crystallization of soldered layer improved markedly the fracure strength of joining at higher temperatures than the softening temperature of glass solder.

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.832-838
• /
• 1996

Thermite reaction products of MgO and Al were added to MgO-C refractory to improve the properties of corrosion against the attack of slag, oxidation and mechanical spalling. Corrosion rate of MgO-C-MgAl2O4 spinel refractory at the ratio of 3.3(CaO/SiO2) slag was smaller than that of MgO-C and MgO-C-Al refractory. The excellent corrosion resistance of the MgO-C-MgAl2O4 spinel refractory against the slag attack was appeared by Al and MgAl2O4 spinel with high melting point and corrosion resistance and the high thermal conductivity and low thermal expansion of AIN. Hot M.O.R at 140$0^{\circ}C$ and the resistance of oxidation weight loss at 90$0^{\circ}C$ were 210kg/cm2 and -12% respectively.

• 한국습지학회지
• /
• 제25권4호
• /
• pp.386-393
• /
• 2023

최근 들어서 국내의 해양치유산업 활성화를 위한 해양치유자원의 효능·효과에 관한 연구개발이 진행 중에 있다. 본 연구는 해양치유자원으로서 잘 알려진 머드 물질에 대한 효능성분 분석을 통해 활용·관리 기준을 제시하였다. 머드물질 시료는 국내 갯벌에서 채취되었으며, 모래질, 실트질 및 점토질 함량은 각각 평균 7.87%, 74.95% 및 17.17%로 머드(실트+점토)의 평균 함량이 90% 이상이었다. 효능성분은 SiO2(68.4%)성분이 가장 높으며, 다음으로 Al₂O₃(13.3%)>Fe₂O₃(4.0%)>K₂O(2.9%)>Na₂O(2.3%)>MgO(1.6%)>CaO(1.0%)>TiO₂(0.7%) 순으로 평균함량이 높았다. 효능성분 분석을 바탕으로 기능성을 나타내는 성분(기능 성분)을 Si, Al, Fe, K, Na, Mg, Ca를 선정하였으며, 또한 품질관리를 목적으로 정하는 성분(지표 성분)은 효능을 가진 성분 중 함량이 높은 K, Mg, Ca로 결정하였다. 결과적으로 기존 문헌을 참고하여 국내 갯벌머드자원이 해양치유자원으로서 활용·관리되기 위해서는 원재료의 머드함량이 70.0% 이상 그리고 지표 성분인 K₂O+MgO+CaO의 합이 5.0% 이상을 기준으로 제시하였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.16-16
• /
• 2012

Mg and its alloys have been of great interest because of their low density of 1.7, 30% lighter than Al, but their wide applications have been limited because of their poor resistances against corrosion and/or abrasion. Corrosion resistance of Mg alloys can be improved by formation of anodic films using anodic oxidation method in aqueous electrolytes. Plasma electrolytic oxidation (PEO) is one of anodic oxidation methods by which hard anodic films can be formed as a result of micro-arc generation under high electric field. PEO method utilize not only substrate elements but also chemical components in electrolytes to form anodic films on Mg alloys. PEO films formed on AM50 magnesium alloy in an acidic fluozirconate electrolyte were observed to consist of mainly $ZrO_2$ and $MgF_2$. Liu et al reported that PEO coating on AM30 Mg alloy consists of $MgF_2$-rich outer porous layer and an MgO-rich dense inner layer. PEO films prepared on ACM522 Mg die-casting alloy in an aqueous phosphate solution were also reported to be composed of monoclinic $Mg_3(PO_4)_2$. $CeO_2$-incorporated PEO coatings were also reported to be formed on AZ31 Mg alloys in $CeO_2$ particle-containing $Na_2SiO_3$-based electrolytes. Magnesium tin hydroxide ($MgSn(OH)_6$) was also produced on AZ91D alloy by PEO process in stannate-containing electrolyte. Effects of $OH^-$, $F^-$, $PO{_4}^{3-}$ and $SiO{_3}^{2-}$ ions and alloying elements of Al and Sn on the formation of PEO films on pure Mg and Mg alloys and their protective properties against corrosion have been investigated in this work. $PO{_4}^{3-}$, $F^-$ and $SiO{_3}^{2-}$ ions were observed to contribute to the formation of PEO films but $OH^-$ ions were found to break down the surface films under high electric field. The effect of pulse current on the formation of PEO films will be also reported.