• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국작물학회지
• /
• 제3권
• /
• pp.1-40
• /
• 1965

본실험은 우리 나라 중부지방에 있어서의 수도의 재배 시기를 이동함에 따르는 실용제형질의 변화를 구명하기 위하여1958~'60년의 3개년에 걸쳐 농업시험장(현 작물시험장) 답작과(수원)에서 시행한 실험으로서 공시품종은 조만성, 초형 등 생태적특성을 달리하는 연산.수원 8002.오조.팔달 및 조광의 5품종을 공시하였으며, 파종기는 3월 2일 ~7월 10일까지를 10일 간격으로 14회에 걸쳐 파종하였고, 또 각 파종기마다 각각 못자리 일수를 30일, 40일, 50일, 60일, 70일 및 8일묘로 하여 이앙하여 실험하였다. 그 결과를 요약하면 다음과 같다. 1. 출수기 : 1) 파종기가 지연됨에 따라서 출수기도 거의 일직선으로 지연되나, 그 정도는 조생종에서 크고 만생종은 작으며, 또 못자리 일수가 길어짐에 따라서 커진다. 2) 출수까지의 일수는 각 품종 모두 파종기의 지연에 따라서 거의 일직선으로 단축하나, 품종에 따라 그 정도의 차이가 있어서 조생종은 단축일수가 작고 만생종이 크다. 그리고 동일품종 내에서도 못자리 일수가 길어짐에 따라 단축일수는 작아졌다. 또 최단축일수에 도달하는 시기도 조생종은 빠르나 만생종은 늦어진다. 또 못자리 일수가 긴 구에서 그 시기는 빨라진다. 품종 및 못자리 일수에 따라 차이가 있으나 어느 시기 이후의 파종기가 되면 단축을 나타내지 않게 되고, 다시 파종기가 늦어지면 한냉한 기후의 영향을 받아 출수일수는 오히려 연장된다. 3) 파종기(X)와 출수까지의 일수(Y)와의 회귀직선식 Y=a+bX의 계수 b(출수일수단축율)와 평균일수일수와는 고도의 상관이 인정되며, 평균출수일수가 클수록, 즉 만생종일수록 파종기의 지연에 의한 출수촉진일수가 컸었다. 4) 어느 품종의 파종기가 동일역일이면 못자리 일수가 극단으로 길지 않은 범위 내에서는(파종기의 지연에 따라서 출수까지의 일수가 직선적으로 단축되는 범위내에서의) 출수일수의 년차간의 변이는 크지 않으므로 목적하는 품종에 대한 수회의 파종기에 걸쳐 출수기의 변동을 조사하여 실험식(파종기와 출수까지의 일수와의 회귀직선식)을 구해 두면 임의의 재배시기에 있어서의 출수기를 추정할 수 있다. 5) 파종기가 3월하순~6월중순, 못자리 일수가 30~50일의 범위에서는 보통기재배에 있어서의 품종의 출수기의 조만을 가지고 그 전후에 해당하는 파종기에 있어서의 각각의 품종에 대한 출수기를 추정할 수 있다. 2. 성숙기 : 6) 출수기가 지연됨에 따라서 성숙한계 출수기의 범위 내에서는 성숙기도 거의 일직선으로 지연된다. 그 정도는 품종 및 못자리 일수의 장단에 의한 차이가 크다. 평균온도의 영향을 받는 범위 내에서는 출수기(X)가 지연됨에 따라서 성숙기간 중의 평균온도(Y)는 그것에 따라서 저하하며 품종간에 차이가 있으나, 전체적으로 보아 양자의 관계를 8월 1일부터 9월 13일까지의 범위에서는 Y=25.53-0.182X의 회귀직선식으로 나타낼 수 있다. 7) 품종의 조만생에 의한 성숙기간에 있어서의 평균온도의 차이가 심하며, 조생종은 최고 28$^{\circ}C$의 고온에서 경과하나 만생종은 22$^{\circ}C$에 불과하다. 8) 성숙기간중의 평균온도(X)와 성숙일수와의 관계는 극히 높은 상관이 인정되며, 양자의 관계를 Y=82.30-1.55X의 회귀직선식으로 표시할 수 있었다. 성숙기간중의 평균기온이 18~28$^{\circ}C$의 범위 내에서는 온도가 1$^{\circ}C$ 상승함에 따라서 성숙일수는 1.55일 단축되는 결과가 되며, 품종별로는 관산이 2.24일로서 단축정도가 컸고, 수원 8002가 0.78일로서 가장 적었다. 따라서 수원지방에 있어서는 평균온도가 18~28$^{\circ}C$의 범위에서는 온도가 상승함에 따라 성숙속도가 빨라진다고 할 수 있다. 9) 각 파종기별로 본 출수까지의 일수(X)에 대한 성숙기간중의 적산온도(Y)와의 관계는 거의 완전한 정의 상관관계가 있고, 성숙기간중의 적산온도는 어느 범위 내에 있어서의 파종기의 이동에 의한 차이는 비교적 작다. 3. 간장 및 수장 : 10) 품종간의 차이는 있으나 비교적 조파가 된 구간에는 간장에 큰 변화는 없으나 계속 파종기가 지연되어 만파가 되면 공시품종 모두 간장의 감소가 뚜렷해졌다. 또 간장의 감소정도는 약묘에서 완만할 뿐만 아니라, 5월 21일~6월 10일 파종과 같이 비교적 만파를 하더라도 별로 감소되지는 않으나, 80일묘와 같은 노숙묘인 때는 보통기재배에서도 급격히 감소한다. 11) 수장의 변화도 간장과 동일한 경향을 보이나 파종기의 지연에 의한 수장의 변화는 30~40일묘에서는 거의 인정되지 않았고, 못자리 일수가 길어지면 수장의 감소가 뚜렷해진다. 4. 수수 : 12) 파종기가 지연됨에 따라서 일정한 시기까지 계속수수는 감소하다가 어느 시기 이후가 되면 새로이 고차분얼의 다량발생으로 수수가 증가한다. 그 시기는 못자리 일수에 따라 차이가 있으며, 30~40 일묘는 5월 31일~6월 10일 파종기인 만파에서 수수가 최대로 감소하며, 70~80일묘의 경우 4월 11일~4월 21일의 파종기에서 이미 수수가 최대로 감소한다. 5. 지경수 : 13) 지경수는 파종기가 지연됨에 따라서 어느 일정한 시기까지는 변화가 없으나, 그 시기가 지나면 수당지경수의 감소가 현저하다. 14) 지경수가 감소되기 시작하는 시기도 30~40 일묘에서는 5월 3일 이후의 파종기가 되나, 80일묘의 경우 5월 31일 파종에서 이미 감소될 뿐만아니라, 5월 31일 파종이 되면 지경수가 3~4개에 불과하였다. 6. 비중과 천입중 : 15) 파종기의 이동에 따라 비중은 서서히 증가하나 어느 시기를 넘으면 급격히 증가하며, 이를 2개의 상이한 회귀직선으로 표시할 수 있다. 16) 이 양직선이 교차되는 지점을 성숙가능한계기로 보면 이 시기는 못자리 일수와 밀접한 관계가 있어서 30~40일묘는 6월 10일 반중기에 해당하나, 70~80일묘에서는 5월 1일로서 못자리 일수가 길어짐에 따라 성숙한계기는 당겨진다. 17) 천입중은 보통기재배에서 가장 무겁고 극조기재배를 하거나 만기재배에서 천입중은 저하한다. 7. 고중 및 완전정조중 : 18) 품종의 조만에 큰 영향없이 III~IV 파종기까지의 조기재배 하에서는 못자리 일수의 장단에 의한 고중의 큰 변이는 없으나, 파종기가 계속 이동하여 보통기재배가 되면 못자리 일수가 길어짐에 따라 차차 고종이 감소되어 오다가 만파가 되자 그 감소정도가 급격해졌다. 19) 파종기(X)와 정조수량(Y)과의 관계는 품종ㆍ못자리 일수를 종합하여 직선에 가까운 포물선으로 나타낼 수 있었다(Y=77.28-7.44X$_1$-1.001X$_2$). 따라서 조파시에는 정조수량의 변이가 작으나 어느 시기보다 파종기가 늦어짐에 따라서 정조수량은 감소하며, 그 정도는 만파인 경우에 심하고, 또 못자리 일수가 길어짐에 따라 더욱 현저하다. 20) 출수일수(X)에 대한 정조수량(Y)의 관계는 품종ㆍ못자리 일수를 구별하지 않고 보아다 회귀직선식으로써 나타낼 수 있었으나, 출수일수가 60~110일 정도까지는 조생종이 수량이 많고 만생종은 만기재배에 해당하므로 정조중의 감소가 심하였고, 출수일수가 140일 정도 이상이 되면 정조중이 거의 증가하지 않은 경향이 뚜렷하였다.

• 아시안잔디학회지
• /
• 제17권4호
• /
• pp.129-146
• /
• 2003

켄터키블루그라스, 퍼레니얼라이그라스, 톨훼스큐 및 한지형 혼합구의 뗏장실험 결과 파종 후 피복도, 균일도, 근계 형성력 및 잔디품질의 차이가 나타났는데 그 결과를 요약하면 다음과 같다. 1. 초종간 피복도 경향은 초기에는 발아속도의 영향을 받았지만, 후기에는 생장습성의 영향을 더 크게 받았다. 파종 후 6주까지는 발아속도가 가장 빠른 퍼레니얼라이그라스의 피복도가 가장 양호하였고, 톨훼스큐는 중간 정도, 그리고 발아속도가 느린 켄터키블루그라스는 가장 저조하였다. 하지만, 파종 후 7주정도 지나서는 퍼레니얼라이그라스나 톨훼스큐에 비해 켄터키블루그라스의 피복도 향상이 가장 두드러지게 나타났다. 2. 조성 후기에 피복도 경향이 달라지게 된 것은 켄터키블루그라스의 경우 생육형이 R-type으로 발아 후 생장이 직립경과 지하경으로 둘 다 가능함으로 생장속도가 빨라지면서 잔디면 피복이 빠르게 되었기 때문이다. 반면, 초기 피복도가 양호한 퍼레니얼라이그라스는 연약한 줄기조직으로 인해 병에 쉽게 걸려 밀도가 떨어졌고, 톨훼스큐는 저온에 약한 특성으로 인해 생장 속도가 저조해지면서 피복도가 떨어졌다. 3. 뗏장의 균일도가 가장 우수한 종류는 켄터키블루그라스였는데 이는 생육형이 R-type으로 지하경 포복으로 낮게 자라는 습성 및 질감이 고운 세엽 특성 때문이었다. 퍼레니얼라이그라스는 켄터키블루그라스와 톨훼스큐의 중간 정도였는데 이는 생육형이 B-type으로 생장이 직립경으로만 이루어지기 때문에 줄기간의 초장 차이가 크게 나타나면서 균일도가 다소 떨어졌다. 그리고 단일 초종구 중 톨훼스큐의 균일도가 가장 불량하였는데 이는 생육형이 B-type으로 직립경으로 생장하고, 또한 질감이 거칠은 광엽 특성과 함께 신초의 전개 각도가 넓어 잔디면이 북더기 모양으로 나타나기 때문이었다. 혼합구 균일도는 색상, 밀도, 질감 및 생육형 등의 특성이 서로 다른 여러 초종이 혼합되었기 때문에 단일 초종 보다 낮았다. 따라서 균질의 품질을 기대 시 여러 종류의 초종을 혼합(mixture)하여 파종하는 것보다는 단일 초종을 사용 (blend)하는 것이 훨씬 더 바람직하다. 4. 또한, 혼합구의 경우 단일 처리구에 비해 신초 출현 시 경합이 강하게 나타났다. 혼합구에서 켄터키블루그라스의 신초 발생 속도는 켄터키블루그라스 100％ 단일종으로만 식재한 것에 비해 30∼40％ 정도 느렸고, 퍼레니얼라이그라스도 퍼레니얼라이그라스 100％ 단일종류에 비해 20∼30％정도 늦었다. 따라서, 뗏장 재배시 여러 종류의 초종을 천편일률적으로 혼합하여 파종하는 것은 바람직하지 않으며, 컨셉에 따라 적절하게 초종 및 품종을 선택해서 사용하는 것이 필요하다. 5. 뗏장의 뿌리 형성 능력은 퍼레니얼라이그라스가 가장 좋았고, 가장 저조한 초종은 켄터키블루그라스였다. 톨훼스큐는 켄터키블루그라스와 퍼레니얼라이그라스의 중간정도로 나타났다. 혼합구의 뗏장 형성 능력은 초종의 혼합비에 따라 뿌리 형성력 차이가 다르게 나타났는데, 특히 퍼레니얼라이그라스 혼합비율이 많을수록 뿌리 형성 능력은 증가하였다. 6. 뗏장 수확시 잔디 품질은 단일 초종구의 품질이 혼합구에 비해 양호하였는데 가장 우수한 초종은 켄터키블루그라스였고, 톨훼스큐는 켄터키블루그라스 다음으로 중간정도, 그리고 퍼레니얼라이그라스는 가장 저조하였다. 켄터키블루그라스는 균일한 잔디 면, 고밀도 및 예초 후 상태가 우수한 특성으로 품질이 양호하였고, 퍼레니얼라이그라스의 품질이 저조하였던 것은 초장이 길어 잔디 면이 누운 상태로 나타나 균일도 저하 및 예초 후 품질이 켄터키블루그라스나 톨훼스큐 보다 떨어지기 때문이다. 그리고 혼합구의 품질은 여러 종류가 혼합됨으로 인해 색상 및 밀도의 균일도가 떨어지고, 또한 예초 시 물결처럼 불균일하게 깎여 잔디 표면이 불량하였기 때문이었다. 7. 골프장이나 경기장 기본 설계 시 초기 피복도 및 뿌리 형성력이 양호한 특성만을 고려해서 퍼레니얼라이그라스위주로 결정하여 시공하는 경우가 많이 있는데, 우수한 잔디 품질을 원할 경우 퍼레니얼라이그라스보다는 켄터키블루그라스 위주의 파종이 더 적절하다고 사료되었다. 왜냐하면 조성 후 품질, 뿌리생육 및 환경 적응성 등을 종합적으로 고려한 잔디 적응력은 켄터키블루그라스가 가장 양호하기 때문이다. 따라서, 골프장이나 경기장 건설 시 초종 선택은 기후, 지형, 인프라, 식생 지반, 장비, 관리 수준, 관리예산 및 기술인력 등의 현장 분석 및 조성 후 잔디품질의 기대수준, 잔디사용정도 및 운영방향 등의 장기적인 컨셉에 따라 결정하는 것이 바람직하다.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 핵의학기술
• /
• 제14권2호
• /
• pp.33-37
• /
• 2010

관상동맥질환의 진단 및 평가에 있어서 myocardial perfusion SPECT검사와 FDG를 이용한 myocardial PET검사 그리고 PET/CT에 장착된 64-slice CT를 이용한 coronary CT angiography를 동시에 실행함으로 검사의 신뢰도와 편의성을 한층 더 높이고자 한다. 먼저 약물부하 myocardial perfusion SPECT검사를 먼저 시행한다. 환자의 피폭경감을 위해서 $^{99m}Tc$-MIBI 10 mCi 로 주사하며 myocardial PET검사를 위해서 지방식을 먹지 않고 ursodeoxcholic acid 100 mg을 생수와 함께 복용하게 하여 1시간 후에 SPECT 영상을 얻는다. 이어서 myocardial FDG PET검사를 시행한다. 혈중의 지방산 농도를 낮추고 심장의 FDG섭취율을 증가시키기 위해 혈중 포도당 농도치에 따라 insulin과 Acipimox를 함께 사용하는 독창적인 경구 당 부하법을 사용하였으며, 환자의 피폭 경감을 위해서 $^{18}F$-FDG 5 mCi를 주사하고 1시간 후에 10분간 gated 영상을 얻으며 필요시 delay 영상을 얻는다. PET검사가 끝남과 동시에 환자는 동일한 position을 하고 연속해서 coronary CTA를 시행한다. 이 검사에서 가장 중요한 것은 심박동수 조절과 환자의 호흡협조이다. 심박동수를 65회 이하로 낮추기 위해 beta blocker 50 mg~200 mg을 의사와 상의하여 복용케 하고 호흡법을 충분히 연습을 시키다. 검사 직전에 isosorbide dinitrate를 3~5회 분무하여 혈관벽의 긴장을 낮추고 혈관을 확장시켜서 coronary artery의 해부학적 형태를 더욱 잘 나타낼 수 있게 한다. 촬영 시 CT 조영제를 4.0~5.0 mL/sec의 압력으로 주입하며 촬영을 한다. Coronary CTA를 이용하면 coronary artery stenosis가 잘 보이며, 약물부하 myocardial perfusion SPECT로 coronary CTA에서 보인 stenosis와 perfusion저하의 상관관계를 검토(culprit vessel 확인)할 수 있으며, FDG PET으로 hibernating myocardium 또는 infarction site의 viability를 확인할 수 있다. 한 가지 검사로 lesion site와 severity 및 치료에 대한 반응 예측이 가능함으로 약물치료, PCI, CABG 등 치료방향을 설정할 수 있다. 또한 모든 검사 과정들이 연속적으로 동시에 이루어지기 때문에 짧은 시간(3시간) 내에 one-stop으로 검사를 종료할 수 있는 큰 장점을 가지게 된다. 그러므로 이 검사법은 ischemic heart disease의 one-stop evaluation에 있어서 유용한 protocol로 보여진다.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권23호
• /
• pp.10061-10066
• /
• 2015

Background: The aetiological relationship between human papillomavirus (HPV) infection and cervical cancer (CC) is widely accepted. Our goal was to determine the prevalence of HPV types in Mexican women attending at the Mexican Institute for Social Security from different areas of Mexico. Materials and Methods: DNAs from 2,956 cervical samples were subjected to HPV genotyping: 1,020 samples with normal cytology, 931 with low-grade squamous intraepithelial lesions (LGSIL), 481 with high grade HGSIL and 524 CC. Results: Overall HPV prevalence was 67.1%. A total of 40 HPV types were found; HPV16 was detected in 39.4% of the HPV-positive samples followed by HPV18 at 7.5%, HPV31 at 7.1%, HPV59 at 4.9%, and HPV58 at 3.2%. HPV16 presented the highest prevalence both in women with altered or normal cytology and HPV 18 presented a minor prevalence as reported worldwide. The prevalence ratio (PR) was calculated for the HPV types. The analysis of PR showed that HPV16 presents the highest association with CC, HPV 31, -33, -45, -52 and -58 also demonstrating a high association. Conclusions: The most prevalent HPV types in cervical cancer samples were -16, -18, -31, but it is important to note that we obtained a minor prevalence of HPV18 as reported worldwide, and that HPV58 and -52 also were genotypes with an important prevalence in CC samples. Determination of HPV genotypes is very important in order to evaluate the impact of vaccine introduction and future cervical cancer prevention strategies.

• 한국유통학회지:유통연구
• /
• 제16권4호
• /
• pp.1-27
• /
• 2011

브랜드확장은 다양한 마케팅 영역 중에서도 전통적으로 활발하게 연구가 진행되어 왔던 영역으로서, 본 연구는 최근 그 중요성이나 활용도가 급증하고 있는 PL(Private Label)제품에 대해 브랜드확장의 개념을 활용하여 차별적으로 접근하고자 하였다. 최근 PL제품에 관한 마케팅연구가 활발하게 진행되고 있으나, 대부분 기존 틀에서 크게 벗어나지 못한 채 단순한 적용에 그치고 있으며, 특히 브랜드확장에 관련된 연구들에서도 PL시장의 특성을 제대로 반영하고 있다고 볼 수 없다. 특히 PL제품의 확장에 있어서는 두 가지 모브랜드가 존재할 수 있는데, 이에 대한 연구는 부재한 상황이다. 이에 본 연구에서는 확장 PL제품의 태도에 영향을 미치는 변수로서 두 가지 모브랜드인 유통업체와 기존 PL제품에 대한 태도를 제시하였다. 또한 개별 모브랜드가 PL제품의 태도에 미치는 영향은 개별 모브랜드와 확장 PL제품간 유사성에 의해 상이할 것이라고 제안하였으며, 유통업체와 기존 PL제품에 대한 태도에 영향을 미치는 변수로서 신뢰와 만족을 제시하였다. 분석결과 유통업체와 기존 PL제품에 대한 태도 모두 확장 PL제품의 태도에 유의한 영향을 미쳤으며 동시에 적합도 정도에 따라 그 영향력이 상이함도 실제 데이터를 통해 검증하였다. 즉 확장 PL제품의 태도는 모브랜드의 적합도가 보다 강하게 형성된 모브랜드의 영향을 더 크게 받는 것을 확인할 수 있었다. 이를 토대로 향후 PL제품을 확장할 경우 소비자가 보다 긍정적인 태도를 갖고 있는 모브랜드에 기초하여 해당 모브랜드와의 연상이 강하게 나타날 수 마케팅 전략을 구사할 필요가 있을 것이다.

• 농업과학연구
• /
• 제4권2호
• /
• pp.254-282
• /
• 1977

벼의 생육(生育) 및 수량(收量)에 관(關)한 주요양적형질(主要量的形質)의 유전(遺傳)에 관(關)한 정보(情報)를 얻고져 1974년(年) 농백(農白), 통일(統一), 팔굉(八紘), 만경(萬頃), 금남풍(金南風)을 교배친(交配親)으로 전조합(全組合) 이면교배(二面交配)를 실시(實施)하여 $F_1$종자(種子)를 얻었으며 1975년(年) 이들 $F_1$ 및 교배친(交配親) 품종(品種)을 재배(栽培)하여 여러 형질(形質)을 조사(調査)하고 그 결과(結果)를 Griffing 및 Hayman의 방법(方法)에 따라 유전분석(遺傳分析)을 하였던 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 통일(統一)을 교배친(交配親)으로 한 조합(組合)에서는 출수기(出穗期)가 늦어지는 쪽이 우성(優性)이었고 출수기(出穗期)가 늦어지는 방향(方向)으로 각(各) 조합(組合)에서 모두 높은 Heterosis를 나타내었던 바 높은 우성효과(優性效果)와 비대립유전자간(非對立遺傳子間)의 교호작용(交互作用)도 인정(認定)되었는데 통일(統一)을 제외(除外)한 품종(品種)을 양친(兩親)으로 한 조합(組合)에서는 출수기(出穗期)가 빠른 쪽이 우성(優性)이었고 상가적효과(相加的效果)가 우성효과(優性效果)에 비(比)해 현저(顯著)히 큰 부분우성(部分優性)을 나타내었으며 비대립유전자간(非對立遺傳子間)의 교호작용(交互作用)도 인정(認定)되지 않았다. 2. 통일(統一)을 교배친(交配親)으로 한 조합(組合)에서는 장간(長稈)쪽으로 높은 Heterosis율(率)을 나타내었으며 간장(稈長)이 긴 것이 짧은 것에 비(比)해 우성(優性)이었고 상가적효과(相加的效果)에 비(比)해 우성효과(優性效果)가 매우 커서 초월우성(超越優性)을 나타내었으며 협의(狹意)의 유전력(遺傳力)은 아주 낮았다. 그리고 교배조합(交配組合)에 따라 모본효과(母本效果)와 정역효과(正逆效果)가 현저(顯著)하였다. 3. 이삭의 추출도(抽出度)는 모든 조합(組合)에서 양친(兩親)의 평균(平均)보다 약간 길었으며 추출도(抽出度)가 길어지는 방향(方向)으로 부분우성(部分優性)을 나타내고 있었다. 우성효과(優性效果)에 비(比)해 상가적작용(相加的作用)이 현저(顯著)히 컷고 광의(廣意) 및 협의(狹意)의 유전력(遺傳力)도 모두 높았다. 추출도(抽出度)에서도 간장(稈長)에서와 같이 모본효과(母本效果)와 정역효과(正逆效果)가 유의(有意)하였다. 4. 지엽각(止葉角)은 대체로 예각(銳角)의 방향(方向)이 우성(優性)이었으나 팔굉(八紘)에서만은 교배조합(交配組合)에 따라 예각(銳角)과 둔각(鈍角)의 두 가지 상반(相反)되는 방향(方向)으로 Heterosis를 보였다. 우성효과(優性效果)가 상가적효과(相加的效果)보다 약간 높았는데 지엽각(止葉角)의 유전(遺傳)에는 교배조합(交配組合)에 따라 비대립유전자간(非對立遺傳子間)의 교호작용(交互作用)도 상당히 크게 작용(作用)한 것으로 보여진다. 5. 지엽장(止葉長)과 지엽폭(止葉幅)에서는 모두 이들이 증가(增加)되는 방향(方向)이 우성(優性)이었으나 Heterosis의 정도(程度)는 교배조합(交配組合)에 따라 각각 다르게 나타났다. 지엽장(止葉長)의 유전(遺傳)에서는 상가적효과(相加的效果)에 비(比)해 아주 높은 우성효과(優性效果)를 보여 초월우성(超越優性)이 인정(認定)되었던 반면(反面) 지엽폭(止葉幅)에서는 우성효과(優性效果)는 적었고 상가적효과(相加的效果)가 매우 크게 나타나 부분우성(部分優性)을 보였으며 광의(廣意) 및 협의(狹意)의 유전력(遺傳力)이 모두 높았다. 그리고 지엽장(止葉長), 지엽폭(止葉幅) 및 지엽각(止葉角)에서는 모두 모본효과(母本效果)나 정역효과(正逆效果)는 인정(認定)되지 않았다. 6. 통일(統一)을 한쪽친(親)으로 하는 조합(組合)의 수장(穗長)은 모두 양친(兩親)에 비(比)해 현저(顯著)히 길었으나 그 외의 조합(組合)에서는 $F_1$의 수장(穗長)이 양친(兩親)의 평균치(平均値)와 비슷하였고 수장(穗長)의 유전(遺傳)에는 상가적(相加的) 효과(效果)보다 우성효과(優性效果)가 크게 작용(作用)하였으며 수장(穗長)이 길어지는 방향(方向)이 우성(優性)이었고 협의(狹意)의 유전력(遺傳力)은 아주 낮았다. 7. 수수(穗數)가 많은 것이 적은 것에 대(對)해 우성(優性)이었으며 $F_1$의 Heterosis 정도(程度)는 교배조합(交配組合)에 따라 각각상이(各各相異)하였다. 수수(穗數)의 유전(遺傳)에는 우성효과(優性效果)가 상가적효과(相加的效果)보다 약간 크게 작용(作用)하고 있어 완전우성(完全優性)에 가까우며 모본효과(母本效果)와 정역효모(正逆效母)에 유의성(有意性)이 인정(認定)되었다. 8. 수당입수(穗當粒數)는 교배조합(交配組合)에 따라 각각(各各) 정부(正負)의 상반(相反)되는 방향(方向)으로 Heterosis가 나타났으며 Heterosis의 정도(程度)도 조합(組合)에 따라 상이(相異)하였다. 평균(平均) 우성방향(優性方向)은 수당입수(穗當粒數)가 증가(增加)되는 쪽이었으나 조합(組合)에 따라 우성(優性)의 방향(方向)은 수당입수(穗當粒數)가 증가(增加)되는 경우와 감소(減少)되는 경우를 동시(同時)에 인정(認定)할 수 있었다. 수당입수(穗當粒數)의 유전(遺傳)에는 우성효과(優性效果)가 아주 크게 나타났으며 비대립유전자(非對立遺傳子)의 교호작용(交互作用)도 인정(認定)되었다. 9. 등숙비율(登熟比率)은 조합(組合)에 따라 출수기(出穗期)의 지연(遲延)에 기인(基因)되는 등숙장해(登熟障害)와 기타 환경(環境)의 영향으로 그 유전양식(遺傳樣式)의 파악(把握)이 거의 불가능(不可能)하였으나 통일(統一)을 제외(除外)한 조합(組合)에서는 등숙비율(登熟比率)이 증가(增加)하는 방향(方向)의 우성효과(優性效果)가 인정(認定)되었다. 10. 천입중(千粒重)은 무거운 것이 가벼운 것에 대(對)해 우성(優性)이었고 우성(優性)의 정도(程度)는 상가적효과(相加的效果)가 우성효과(優性效果)에 비(比)해 현저(顯著)히 높아 부분우성(部分優性)을 나타내었다. 천입중(千粒重)은 광의(廣意) 및 협의(狹意)의 유전력(遺傳力)이 모두 높았으며 모본효과(母本效果)나 정역효과(正逆效果)는 인정(認定)되지 않았다. 11. 고중(藁重)은 통일(統一)을 한쪽 친(親)으로 하는 조합(組合)에서는 고중(藁重)이 무거워지는 방향(方向)으로 높은 Heterosis를 보였으나 그외(外)의 조합(組合)에서는 양친(兩親)의 평균(平均)보다 고중(藁重)이 감소(減少)되었고 조합(組合)에 따라 우성(優性)의 방향(方向)이 정부(正負)로 나타날 뿐 아니라 그 정도(程度)도 서로 다르며 비대립유전자간(非對立遺傳子間)의 교호작용(交互作用)도 현저(顯著)하였다.

• Radiation Oncology Journal
• /
• 제23권3호
• /
• pp.186-193
• /
• 2005

목적: 방사선치료의 핵심 장비인 선형가속기의 10년간 고장 기록을 분석하여 효율적인 관리 지표로 활용하고자 한다. 대상 및 방법: 1994년 4월부터 2004년 12월까지 10년 8개월간 의공기술과에서 기록한 장비 수리일지와 사용자가 기록한 업무일지의 내용을 통계분석을 통해 관리실태를 분석했다. 장비 장애 요인을 다각적으로 분석하기 위해 고장 원인을 치료기 부위별로 세분했고, 고장 발생 시 치료업무에 미치는 영향에 따라 세 단계로 구분하여 조사했다. 또한, 장비 사용량이 고장에 미치는 영향을 분석하기 위해 연간 치료 환자 수와 고장건수, 중요 부속의 평균 수명, 수리비용 등을 분석했다. 결과: 10년간 발생한 전체 고장건수는 587건이였으며, 이중 조사헤드부의 고장이 전체 건수의 $20\%$ 차지해 가장 높게 나타났고, 고장이 미치는 영향에서는 일시적 장애에 해당하는 '조사능력 저하'상태의 고장이 $41\%$를 차지해 가장 높았다. 고장 부위에 따른 장애 영향 분석에서는 장애 등급이 가장 높은 '조사 불가능'상태의 고장이 가속부에서 전체 건수의 약 $10\%$를 차지해 가장 높게 나타났으며, 고장과 관련된 각종 지표 및 수리비용은 사용연수 및 치료건수가 증가함에 따라 함께 증가했다. 중요 부속의 평균 수명은 클라이스트론과 싸이라트론의 경우 치료건수가 증가함에 따라 교체 주기가 빨라져 각각 제조사 권고치의 $42\%,\;83\%$ 수준이었다. 결론; 안정적인 치료서비스 제공을 위해서는 사용 연수가 증가함에 따라 장비 관리의 필요성이 더욱 중요시되어야하며, 10년간 장비 관리기록을 통해 얻은 각종 지표가 향후 예방적 관리의 좋은 지침이 될 것으로 생각된다.방사선으로 인한 폐손상 시에 항섬유증 약물로의 사용가능성을 확인하였다.방향으로 2.1 mm, 그리고 SI 방향으로 1.7 mm이다. 결론: 연구 결과 SSD, CLD, 클립의 움직임 및 isocenter의 위치변화 측면에서 분석될 경우 그다지 큰 오차는 발생하지 않았음을 보여준다. 그러므로 본 연구결과 유방암 환자의 경우 진단용 CT를 사용한다 하더라도 준비오차는 모의 CT를 사용하는 경우와 비교하여 차이가 없음을 알 수 있다. 그러나 모의치료와 CT스캔 사이의 준비오차를 감소하기 위해서는 CT 영상 획득 시 환자 위치고정에 특별한 주의를 기울여야 한다.EX>$\alpha/\beta$=10인 경우 $62.0\~121.9\;Gy_{10}$ (중앙값: $93.0\;Gy_{10}$)의 분포를, ${\alpha/\beta}=3$인 경우 $93.6\~187.3\;Gy_3$ (중앙값=$137.6\;Gy_3$ )의 분포를 보였다. MD-BED $Gy_3$는 직장합병증 발생과의 관계는 통계적으로 유의하였고, 방광합병증과는 유의하지 않았다. 직장합병증과의 연관성은 MD-BED $Gy_3$보다 개별 환자의 직장전벽 총 선량 BED값인 R-BED $Gy_3$가 훨씬 더 높았다. 요도카테터 풍선의 후방지점이 대변하는 방광의 총 선량 BED값인 V-BED $Gy_3$도 방광합병증과 경향성 테스트에서 통계적 유의성을 보였다. 하지만, 어떠한 방사선선량도 골반제어율과 의미 있는 상관관계를 보이지 않았다. 본 기관에서 주치의의 선호도에 따라 강내근접치료가 외부방사선치료의 중간에 시행되는

• 한국산림과학회지
• /
• 제16권1호
• /
• pp.1-32
• /
• 1972

본연구(本硏究)는 주요조림수종(主要造林樹種)인 송백류중(松柏類中) 특(特)히 Sub-genus Diploxylon내(內)의 종간교잡(種間交雜)에 의(依)하여 생산(生産)된 일대잡종(一代雜種) ${\times}$P. rigielliottii, ${\times}$P. rigiradiata, ${\times}$P. rigiserotina 및 ${\times}$P. densithunbergii의 임성종자확득율(稔性種字穫得率)을 기준(基準)으로한 교배친화력(交配親和力)과 분류학상(分類學上)의 유연관계(類緣關係)를 검토(檢討)하는 동시(同時)에 조림지(造林地)에 있어서의 생장비교(生長比較), 침엽(針葉)의 외부(外部) 및 해부형태비교(解剖形態比較), phenol성물질(性物質)에 의(依)한 특성비교(特性比較) 및 천연적송림(天然赤松林)에 대(對)한 이입교잡현상등(移入交雜現象等)을 구명(究明)하여 금후계획적조림(今後計劃的造林)에 공헌(貢獻)할 잡종채종림조성(雜種採種林造成) 여부(與否)와 일대잡종(一代雜種)과 그 양친종간(兩親種間)의 차이점(差異點)을 분별관찰(分別觀察)한 결과(結果) 다음과 같은 성적(成績)을 얻었다. 1. 각공시수종(各供試樹種)을 Shaw, Pilger 및 Duffield 등(等)의 분류식(分類式)에 준(準)하여 각조합별(各組合別) 임성종자확득율(稔性種字穫得率)을 기준(基準)으로 교배친화력(交配親和力)과 유연관계(類緣關係)를 검토(檢討)한 바 각조합(各組合)의 양친종간(兩親種間)에는 상당(相當)한 교배친화력(交配親和力)이 있었고, 근연간(近緣間)임을 알수 있었으며, 각조합별(各組合別) 최고임성종자확득율(最高稔性種字穫得率)은 28~58%이었다(표(表) 13). 2. 조림지(稠林地)에 있어서 각일대잡종송(各一代雜種松)의 생장비교(生長比較)에서 특(特)히 ${\times}$P. rigiserotina는 수고(樹高)와 근원경(根元徑)에서 수종간(樹種間)에 1% 수준(水準)으로 고도(高度)의 유의성(有意性)이 있었으므로 재적비(材積比)에서도 종자모수(種字母樹) 보다 109~155%의 보다 월등(越等)한 생장(生長)을 보여 조림상(造林上) 유용성(有用性) 가치(價値)가 있는 우수(優秀)한 일대잡종(一代雜種)으로 기대(期待)되었다(표(表) 16, 17). 3. 각일대잡종송(各一代雜種松)은 내한성(耐寒性)에 있어서 종자모수(種字母樹)의 형질(形質)을 받어 전연(全然) 동해(凍害)를 받지 않았으므로 내한력(耐寒力)이 강(强)함을 알수있었다. 4. 침엽장비교(針葉長比較)에서 일대잡종(一代雜種)의 양친종간(兩親種間)에는 현저(顯著)히 식별(識別)되었으며, 화분모수(花粉母樹)의 형질(形質)을 받은 ${\times}$P. rigiserotina는 종자모수(種字母樹) 보다 65%의 보다큰치(値)를 보여 현저(顯著)하게 식별(識別)되었으나 타일대잡종송(他一代雜種松)은 종자모수(種字母樹)의 형질(形質)을 받어 엽장(葉長)만으로는 잡종성(雜種性)을 용이(容易)하게 식별(識別)하기 어려웠다(표(表) 21). 5. 침엽(針葉)의 해부형태(解剖形態)에 있어서 제형질중(諸形質中) 일부(一部) 예외(例外)도 있었으나 각일대잡종송(各一代雜種松)은 대부분(大部分)이 hypoderm에서 강화(强化)되었고, resin canal에서는 조합(組合)에 따라 종자모수(種字母樹) 또는 화분모수(花粉母樹)의 우성형질(優性形質)을 나타냈으며, fibrovascular bundle에서는 종자모수(種字母樹)와 같이 상이(相離)된 형질(形質)을 나타냈으므로 각일대잡종(各一代雜種)과 그 양친종간(兩親種間)의 식별(識別)이 어느정도(程度) 가능(可能)함을 보았다. 특(特)히 ${\times}$P. densithunbergii에서는 RDI 0.73으로 화분모수(花粉母樹)에 가까운 형질(形質)을 보였다(그림 1, 표(表) 22). 6. Phenol 성물질(性物質)에 의(依)한 특성비교(特性比較)에서 공시일대잡종중(供試一代雜種中) 특(特)히 ${\times}$P. rigielliottii, ${\times}$P. rigiradiata 및 ${\times}$P. rigitaeda는 공(共)히 Rf-0.46인 phenol 물질(物質) 7번(番)이 P. rigida와 동일(同一)하게 담황색(淡黃色)으로 반응(反應)되었으나 화분모수(花粉母樹)에는 반응(反應)이 나타나지 않았으므로 양친간(兩親間)에는 현저(顯著)한 식별(識別)을 할수있었다. 이 결과(結果)는 장차(將次) 차대검정(次代檢定)은 물론(勿論) 교잡육종(交雜育種)에 있어서 잡종성조기식별(雜種性早期識別)의 가능성(可能性)을 보았고, ${\times}$P. rigiserotina와 ${\times}$P. densithunbergii는 양친종(兩親種)과 동일(同一)한 반응(反應)을 나타내어 식별(識別)을 할수없었음을 보아 양친종(兩親種)이 근연간(近緣間)임을 알수있었다(그림 2, 표(表) 23). 7. TLC에 의(依)한 phenol성물질(性物質)의 분리(分離) 및 반응현상(反應現象)은 동일수종내(同一樹種內)에서는 개체별(個體別), 채취부위별(採取部位別), 수령별(樹齡別) 및 화분산지별(花粉産地別)에 관계(關係)없이 동일(同一)한 분리(分離) 및 반응현상(反應現象)을 보였으며, 전개용매(展開溶媒)에 있어서도 Aceton-Chloroform(3:7v/v)을 사용(使用)하였을때나 Benzene-Methanol-Acetic acid(90:16:8 v/v)를 사용(使用)했을때나 동일(同一)한 반응(反應)을 볼수있었다. 8. 천연적송림(天然赤松林)에 있어서의 이입교잡현상(移入交雜現象)은 조사지(調査地) 범위내(範圍內)에서는 동해(東海) 및 서해안지방(西海岸地方)의 각조사임분(各調査林分)의 대부분(大部分)이 잡종성(雜種性)인 사실(事實)과 동해안(東海岸) 보다 서해안지방(西海岸地方)의 조사임분(調査林分)이 월등(越等)히 높은 잡종성(雜種性)임을 알수있었다(표(表) 24, 25). 9. 한국(韓國) 및 일본(日本)에서 선발(選拔)된 수형목(秀型木)은 RDI에 있어서 순수(純粹)한 적송개체(赤松個體)를 발견(發見)할수 없었으며, 본공시목(本供試木)의 전부(全部)가 흑송(黑松)의 형질(形質)을 가진 잡종성(雜種性)임을 알수있었으므로 이러한 수형목(秀型木)은 잡종성(雜種性)에 기인(起因)한 것이라 사료(思料)된다. (그림 3,4, 표(表) 26,27).