• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.507-511
• /
• 2018

This paper proposes a method for system development for high speed (300MHz) test of system IC semiconductors. The high-speed test system proposes a high-speed test circuit interface and a PCB design method for noise reduction. This paper proposes evaluation items and procedures for verifying the performance of the developed system. System IC The development of high speed test systems will help optimize the development of domestic system IC test equipment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.12
• /
• pp.2503-2510
• /
• 2015

This paper presents a single-phase energy measurement IC to measure electric power quantities. The entire IC includes two programmable gain amplifiers (PGAs), two ${\sum}{\Delta}$ modulators, a reference circuit, a low-dropout (LDO) regulator, a temperature sensor, a filter unit, a computation engine, a calibration control unit, registers, and an external interface block. The proposed energy measurement IC is fabricated with $0.18-{\mu}m$ CMOS technology and housed in a 32-pin quad-flat no-leads (QFN) package. It operates at a clock speed of 4,096 kHz and consumes 10 mW in 3.3 V supply.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.265-268
• /
• 1999

In this paper, a wideband MMIC distributed amplifier was designed using the fabricated PHEMT with the unit gate width of 80 ${\mu}{\textrm}{m}$ and 4 gate fingers at our Lab. S$_{21}$ gains are 7.1 ~ 10.0 ㏈. Input and output reflection coefficients obtained from the distributed amplifier in the frequency range of DC~25 ㎓ are lower then -8 ㏈. A chip size of the designed wideband MMIC distributed amplifier is 1.9 mm $\times$ 1.1 mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.25-28
• /
• 2002

Contact type Ic measurement system is needed to measure Ic continuously for long Bi-2223 tapes. Voltage and current terminals were designed several shapes for 4-probe method Ic measurement. Voltage terminals were made with brass and current terminals were made with Cu. We used 2 kinds of Bi-2223 tapes with different strength. When we measured Ic of Bi-2223 tape with Ag-Mg sheath, The proper weight was 0.3 kg and sharp pin type was better. according to voltage terminal shape and load. In case of Bi-2223 tape with Ag-Mn sheath, the proper terminal weight was 4 kg and sharp pin type was bad. It was possible to make continuous contact type Ic measurement system because We could get proper data - terminal shapes and loads - through these experiments.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.499-500
• /
• 2008

In this paper, we design and implement the monolithic power factor correction IC for system power modules using a high voltage(50V) CMOS process. The power factor correction IC is designed for power applications, such as refrigerator, air-conditioner, etc. It includes low voltage logic, 5V regulator, analog control circuit, high-voltage high current output drivers, and several protection circuits. And also, the designed IC has standby detection function which detects the output power of the converter stage and generates system down signal when load device is under the standby condition. The simulation and experimental results show that the designed IC acts properly as power factor correction IC with efficient protective functions.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1165-1175
• /
• 2015

This paper presents an advanced sensorless permanent magnet (PM) brushless motor controller integrated circuit (IC) employing an automatic lead-angle compensator. The proposed IC is composed of not only a sensorless sine-wave motor controller but also an isolated gate-driver and current self-sensing circuit. The fabricated IC operates in sensorless mode using a position estimator based on a sliding mode observer and an open-loop start-up. For high efficiency PM brushless motor driving, an automatic lead-angle control algorithm is employed, which improves the efficiency of a PM brushless motor system by tracking the minimum copper loss under various load and speed conditions. The fabricated IC is evaluated experimentally using a commercial 200 W PM brushless motor and power switches. The proposed IC is successfully operated without any additional sensors, and the proposed algorithm maintains the minimum current and maximum system efficiency under $0N{\cdot}m$ to $0.8N{\cdot}m$ load conditions. The proposed IC is a feasible sensorless speed controller for various applications with a wide range of load and speed conditions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1236-1239
• /
• 2009

Each LCD TFT panel requires a power supply IC on the panel board. The IC provides the power rails for the timing controller, source and gated driver IC and others. The industry trend moves towards higher integrated devices. The challenge for the panel manufacturer is the development and implementation of such an IC in cooperation with the semiconductor supplier. If not done carefully the solution will not reduce the overall solution cost or can't provide the expected performance and reliability. This paper discusses the key considerations to successfully develop and integrate a highly integrated LCD bias IC into the system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.83-88
• /
• 2007

In this paper, we propose the function verification method of the OLED(Organic Light Emitting Diode) drive IC using PLI verification method. This method uses the HDL(Hardware Description Language) simulator, PLI(Programing Language Interface), and GUI (Graphic User Interface) image viewer. This method improves the execute efficiency 40 times than conventional function verification methods. The proposed method can be used efficiently for function verification of DDI(display driver IC) design step.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.289-295
• /
• 2008

In this paper, we designed the off-line PWM(Pulse width modulation) control IC for flyback type power converter to reduce the standby power consumption. In normal state, this off-line PWM IC generates the output pulse with $40\sim60kHz$ frequency and duty ratio of $20\sim88%$. When SMPS operates in standby mode, this IC generates the output pulse with 33kHz frequency and duty ratio of 1 %. SPICE simulation was performed to verify the standby power consumption of the power converter with designed of-line PWM IC. Power converter with designed off-line PWM IC consumes less than 0.3W when it operates in standby mode condition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.122-122
• /
• 2009

최근 PC의 성능이 향상되면서, 고성능의 전원공급 장치가 요구되고 있다. 특히 CPU에 대전력을 공급하는 싱크로너스 벅 컨버터는 파워 MOSFET을 구동하기 위해 별도의 구동 IC가 필요하다. 본 논문은 adaptive 지연을 이용하여 파워 MOSFET을 구동하는 싱크로너스 벅 구동 IC를 설계하였다. 고정밀도의 밴드캡 기준회로와 비교기를 이용하여 30 ns의 adaptive 지연을 생성하며, 전력소모를 줄이기 위해 저전압에서 동작하는 UVLO(under voltage lock out)를 설계하였다. 또한 상단 파워 MOSFET을 구동하기 위하여 부트스트랩 방식을 이용하며, 부트스트랩 다이오드를 IC 내부에 내장하여 컨버터의 설계비용을 줄였다. 설계한 구동 IC의 동작 전압 범위는 8 V - 15 V이며, 출력 전류는 최대 2A이다. 싱크로너스 벅 구동 IC는 $0.5\;{\mu}m$ BiCMOS(Bipolar-CMOS) 공정 파라미터를 사용하여 설계되었으며, 시뮬레이션은 Cadence사의 Spectre를 이용하였다.