• Korean Journal of Materials Research
• /
• v.2 no.4
• /
• pp.263-269
• /
• 1992

Low-firing dielectric materials with negative small temperature coefficients were investigated. The newly developed materials are based on Ti$O_2$(100-x)/ CuOx(X=1~5wt%) with small amount of Mn$O_2$ additive. The sample without CuO was not sintered at 90$0^{\circ}C$. As CuO content was increased the sample could be sintered at low temperature. However, the dielectric constant was decreased and the dielectric loss was increased. In the case of adding 3wt% CuO and 0.6wt% Mn$O_2$, the dielectric constant and the Q values appeared very high.

• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1119-1123
• /
• 2002

Nanostructured spinel NiZn ferrites were prepared by the sol-gel method from metal nitrate raw materials. Analyses by X-ray diffraction and scanning electron microscopy showed the average particle size of NiZn ferrite was under 50 nm. The single phase of NiZn ferrites was obtained by firing at 250${\circ}C$, resulting in nanoparticles exhibiting normal ferrimagnetic behavior. The nanostructured $Ni_{1-X}Zn_XFe_2O_4$ (x=0.0∼1.0) were found to have the cubic spinel structure of which the lattice constants ${\alpha}_2$ increases linearly from 8.339 to 8.427 ${\AA}$ with increasing Zn content x, following Vegard's law, approximately. The saturation magnetization $M_s$ was 48 emu/g for x=0.4 and decreased to 8.0 emu/g for higher Zn contents suggesting the typical ferrimagnetism in mixed spinel ferrites. Pure NiZn ferrite phase substituted by Cu was observed before using the additive but hematite phase was partially appeared at $Ni_{0.2}Zn_{0.2}Cu_{0.6}Fe_2O_4$. On the other hand, the hematite phase in this NiZn Cu ferrite was disappeared after using the additive of acethyl aceton with small amount. The saturation magnetization Ms of $Ni_{0.2}Zn_{0.8-y}Cu_yFe_2O_4$(y=0.2∼0.6) as measured was about 51 emu/g at 77K and 19 emu/g at room temperature, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.260-261
• /
• 2005

$YBa_2Cu_3O_{7-\delta}$ superconductor films have been prepared on silver substrates by electrophoretic deposition. As silver does not react with $YBa_2Cu_3O_{7-\delta}$ compound and has little influence on its superconductivity, it is usually doped in $YBa_2Cu_3O_7$ to improve the strength of the material and eliminate micro-cracks. It has been proved that Ag additive can lower the melting temperature of $YBa_2Cu_3O_{7-\delta}$ and act as linking bridge among $YBa_2Cu_3O_{7-\delta}$ particles, thus in this paper Ag doped $YBa_2Cu_3O_{7-\delta}$ thick films are prepared by electrophoretic co-deposition. As there are only some referenced experience formula and models for co-electrophoretic deposition and does not exist unified explanation, the behavior of Ag particles during co-electrophoretic deposition is also studied.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.870-875
• /
• 2011

The $(Na_{0.52}K_{0.44})(Nb_{0.9}Sb_{0.06})O_3-0.04dLiTaO_3$ (NKNS-LT) ceramics with various $Cu_2O$ concentration were prepared by the conventional solid state reaction method. The $Cu_2O$ content was varied in the range of 0.1~0.4 wt%. The effects of Cu on microstructure, crystallographic phase transition, and piezoelectric properties were investigated. The material with perovskite structure had a tetragonal phase (T1) when $Cu_2O$ concentration was less than 0.3 wt% and it transformed to another tetragonal phase (T2) when the $Cu_2O$ amount was greater than 0.3 wt%. The phase boundary between T1 and T2 phases appeared at around 0.3 wt% of $Cu_2O$ concentration. The piezoelectric properties were shown the maximum values at the composition of the phase boundary. The electro-mechanical coupling factor ($k_p$) was 0.42 and the piezoelectric charge constant ($d_{33}$) was 245 pC/N at the 0.3 wt% of $Cu_2O$ concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.55-58
• /
• 2003

[ $YBa_2Cu_3Ox$ ](YBCO) oxide superconductor was prepared by sol-gel method to improve its superconducting properties, and it was made to be a fine powder, which has the same property of solid state reacted powder. $BaPbO_3$ was synthesized with $BaCO_3$, BaO, PbO, and $PbO_2$ and analyzed by XRD. YBCO superconductor was prepared by use of sol-gelled YBCO powder and additive $BaPbO_3$ and its critical temperature and transition temperature were shown as 91.9 K, 3.7 K respectively in case 20 wt.% $BaPbO_3$ was added to pure sol-gelled YBCO powder.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.9-12
• /
• 2004

The effect of x wt% CuO-y wt% $V_2O_5$ content on the microwave properties of $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ (PCFNS) ceramics was investigated. In order to decrease the sintering temperature and use as a Low Temperature co-firing Ceramics (LTCC), CuO-$V_2O_5$ are added in the PCFNS. The bulk density, dielectric constant (${\varepsilon}_r$) and quality factor(Q${\cdot}f_0$) increased with increase in CuO content within a limited value. The microwave properties were degraded with increases in $V_2O_5$ content. The temperature coefficient of the resonant frequency (${\tau}_f$) of PCFNS was shifted to positive value abruptly with increasing the $V_2O_5$ content, while the ${\tau}_f$ was slightly shifted to positive value with increasing the CuO content. The optimized microwave properties, ${\varepsilon}_r$ = 88, Q${\cdot}f_0$ = 6100 (GHz), and ${\tau}_f$ = 18 ppm/$^{\circ}C$, were obtained in $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ with 0.2wt% CuO 0.05 wt% $V_2O_5$ and sintered at $1000^{\circ}C$ for 3 h. The relationship between the microstructure and microwave dielectric properties of ceramics was studied by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM)

• Korean Journal of Materials Research
• /
• v.13 no.8
• /
• pp.531-536
• /
• 2003

The electromagnetic properties and microstructures of the ferrites based on ($Ni_{0.2}$ $Cu_{0.2}$ $Zn_{0.6}$)$_{1.085}$($Fe_2$$O_3$)$_{0.915}$ were investigated by changing the amount of additive SnO$_2$and CaO and the sintering temperatures. Addition of $SnO_2$caused pores in the specimen. There was no variation of grain size by changing the amount of additives. Total loss was reduced when ($Ni_{0.2} $Cu_{0.2}$ $Zn_{ 0.6}$)$_{1.085}$ ($Fe_2$$O_3$)$_{0.915}$ composition was sintered at $1150^{\circ}C$ rather than $1300^{\circ}C$. Addition of CaO was useful to reduce the total loss because it increased the sintering density. The lowest total loss was obtained when 0.06 wt% $SnO_2$and 0.4 wt% CaO were added at the same time.

• Applied Chemistry for Engineering
• /
• v.2 no.1
• /
• pp.30-37
• /
• 1991

The production of hydrogen from steam by reduced iron with additives such as CuO, $In_2O_3$, $MoO_3$ and $WO_3$ has been kinetically investigated. It was shown that all additives have a promoting effect on reaction activity in the order of $$MoO_3{\gg}In_2O_3{\sim_=}WO_3{\sim_=}CuO$$. The shrinking core model was applied to predict the complete conversion time and the results were quite comparable with experimental values. The reaction was carried out in a fixed flow reactor packed with reduced iron with 1 wt % of additives under the conditions, $600-750^{\circ}C$, Ar flow rate of 1 L/min and steam partial pressure of 0.085 atm. The apparent activation energies were 14.2, 20.9, 21.3, 22.4 and 27.9 kJ/mol with $MoO_3$, $In_2O_3$, $WO_3$, CuO and without additive, respectively.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.81-88
• /
• 1997

Vanadate glasses using $B_2O_3$ as a network former and with CuO additive were mainly investigated in relation to electrical properties. Crystalline phases formed by heat-treatment in each composition were examined and dc electrical conductivity changes of the glasses were analyzed. Crystalline phases were identified as $V_3O_5,\;a-CuV_2O_6\;and\;{\beta}-CuV_2O_6$ by XRD analysis. Crystallization degrees of $V_2O_5$ and ${\beta}-CuV_2O_6$ were little changed with heat-treatment time, but those of ${\alpha}u-CuV_2O_6$ were changed sharply with heat-treatment time. The more crystallization of ${\alpha}u-CuV_2O_6$ occurred, the higher electrical conductivity was observed. Electrical conductivities with $10^{-2}~10^{-4}/{\Omega}/cm$ at room temperature(303K) could be obtained by controlling the glass compositions. The electrical conductivities were increased with increasing of $V_20_5$ content and decreasing of alkality($CuO/B_2O_3$). In this study, electron was proved to be charge carrier by seebeck coefficient measurement. Accordingly, the glasses are believed to be n-type semiconductor. Calculated activation energies for the conduction were in the range 0.098-0.124 eV. Electrical conduction mechanism was small polaron hopping without showing variable range hopping in the temperature range $30~200^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.29 no.3
• /
• pp.150-154
• /
• 2019

This study investigates the effect of MnO2 and CuO as acceptor additives on the microstructure and piezoelectric properties of $0.96(K_{0.5}Na_{0.5})_{0.95}Li_{0.05}Nb_{0.93}Sb_{0.07}O_3-0.04BaZrO_3$, which has a rhombohedral-tetragonal phase boundary composition. $MnO_2$ and CuO-added $0.96(K_{0.5}Na_{0.5})_{0.95}Li_{0.05}Nb_{0.93}Sb_{0.07}O_3-0.04BaZrO_3$ ceramics sintered at a relatively low temperature of $1020^{\circ}C$ show a pure perovskite phase with no secondary phase. As the addition of $MnO_2$ and CuO increases, the sintered density and grain size of the resulting ceramics increases. Due to the difference in the amount of oxygen vacancies produced by B-site substitution, Cu ion doping is more effective for uniform grain growth than Mn ion doping. The formation of oxygen vacancies due to B-site substitution of Cu or Mn ions results in a hardening effect via ferroelectric domain pinning, leading to a reduction in the piezoelectric charge coefficient and improvement of the mechanical quality factor. For the same amount of additive, the addition of CuO is more advantageous for obtaining a high mechanical quality factor than the addition of $MnO_2$.