• Korean Journal of Materials Research
• /
• v.4 no.4
• /
• pp.459-465
• /
• 1994

A-axis oriened YBCO thin flims were grown on $LaAIO_{3}$ single crystal substrate by off-axis rf magnetron sputtering method. We used two kinds of process to get a-axis oriented fi1ms;one-step process and two-step process. In one-step process, films are grown in single step in which substrate temperature( $T_s$) is in the range of $590^{\circ}C$ to $680^{\circ}C$. On the other hand, in two step process a-axis oriented thin film templates i f about 30nm thickness is deposited at low temperature first, and subsequently films are grown at elevated temperature to the final thickness of about 100nm. In the case of one step process($T_s$ ~)$600^{\circ}C$), prefered a-axis orientation is dominant and Cu-rich phases segregate at the surface. Segregations decrease and ($00 \ell$) peaks increase upon increasing $T_s$. The films prepared by two step method appeared to have strong(h00) peaks as the deposition rate increased. Microstructure shows pin holes resulted from mixed phases of a-axis and c-axis oriented films. In both cases of one step and two step process, as TS decreases, prepared films show stronger a-axis orientation. However electrical properties of the films are depressed with lower $T_c$ and wider $\Delta T$ as $T_s$ decreases.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1998-2000
• /
• 2005

The effects of the addition of nanocrystalline Y2O3 powder on the microstructure and superconducting properties have been investigated in YBCO films prepared by TFA-MOD process. Precursor solution doped with extra $Y_2O_3$ Powder was prepared by adding $Y_2O_3$ powder into a stoichiometic precursor solution with a cation ratio of Y:Ba:Cu=1:2:3. Coating solutions with and without $Y_2O_3$ doping were coated on $LaAlO_3(100)$ single crystal by a dip coating method, cacination and conversion heat treatments were performed at the controlled atmosphere containing water vapor Current carry capacity(Jc) of YBCO film was enhanced about 50% by $Y_2O_3$ doping. It is thought that the enhancement of Jc is due to the better connectivity of YBCO grains and/or the flux pinning by the presence of nanocrystalline $Y_2O_3$ Particles embedded in YBCO grains.

• Korean Journal of Materials Research
• /
• v.5 no.5
• /
• pp.598-605
• /
• 1995

Thin films of $YB_{2}Cu_{3}O_{7-d}$ were prepared on various substrated of MgO(100), $SrTiO_{3}$, and $LaAlO_{3}$ by using off-axis magentron sputtering methods and annealing in-situ. The prarameters of film fabrication processes had been optimized through a "follow the lcoal maxima" strategy to yield good quality films in therms of the critical temperature $T_{c}$ and the critical current density $J_{c}$. Optimizedproecsses employing a plane magndtron and an cylindrical magnetron yielded $T_{c}$>90K along with $J_{c}$$10^{6}$A/$\textrm{cm}^2$ at 77K and > 2${\times}$$10^{7}$A/$\textrm{cm}^2$ at 5K. The sampels, however, showed degradationinthe properties, after chemical etching for fabrication of microbridges with the line width of 2-10 mocrons. In particular, the value of $T_{c}$ for the microbridges of 2microns was as small as 80%. The degradation was strongly dependent on the line width through a formula : $T_{c}$(e)=$T_{c}$)b) [1-a exp(-1000 bL)} where $T_{c}$(e) and $T_{c}$ (b) are the values of $T_{c}$ in the absolute scale measured after and before chemical etching, respectively and L is the line width in mm. By utilizing a best fitting technique, the proper constant values of a and to b were found as exp(-1.2) and 0.22, respectively. This formula was very useful in estimatiing the upper limit of the device operationtemperature.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.125-127
• /
• 2000

We report high pressure synthesis of Sr$_{0.9}$Sm$_{0.1}$CuO$_2$. Powder x-ray diffraction showed that the synthesized compounds have infinite layer structure as a major component. Slow heating at the first stage of heating processes after pressurization resulted in several larger grains. The largest grain was found to have the longest edge length of about 100 micrometer. Through magnetic property measurement in superconducting state, we found that pinning in this compound has substantial difference from that of La doped infinite layer, which has no unpaired spin at Sr site.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.151.1-151.1
• /
• 2016

Complex oxide heterointerfaces have been extensively explored in the past due to the novel phenomenon emerging at such interfaces that differ from their individual bulk counterparts. The integration of a ferromagnetic (FM) material with the superconducting (SC) material leading to proximity effect is one of the commonly studied phenomenon in these heterostructures. In continuation, we have stabilized the FM layer La0.7Ca0.3MnO3 (LCMO) on SC material YBa2Cu3O7-${\delta}$ (YBCO) using pulsed laser deposition technique and explored the structural, magnetic, electrical and magneto-transport properties of this heterostructure. ${\Phi}$-scan measurements confirm the epitaxial nature of LCMO/YBCO heterostructure grown on single crystalline SrTiO3 substrate. The FM transition of LCMO and SC transition of YBCO are observed in the magnetization measurements of the bilayer structure. Through electrical measurements, we understood that the proximity effect leads to lowering of the SC transition of YBCO. The role of interface in the bilayer structure is also realized through electrical transport measurements.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.415-423
• /
• 1996

Thin film technologies for fabricating SQUIDs involve etching and deposition procedures with the proper substrate materials and $YBa_2Cu_3O_{7-d}$ (YBCO) as the high $T_c$ superconductor. YBCO were prepared on various substrates of MgO, $SrTiO_3$, and $LaAlO_3$ by using off-axis magnetron sputtering methods and annealing in-situ. The parameters of film fabrication processes had been optimized to yield good quality films in terms of the critical temperature $T_c$ and the critical current density $J_c$. The optimized processes yielded $T_C$>90K along with $J_c$>$10_6A$$extrm{cm}^2$ at 77K and>$2\times10_7A/Cm^2$ at 5K. We fabricated step-edge type dc-SQUIDs and directly coupled magnetometers, producing step edges on MgO(100) substrates by etching with Ar-ion beam, depositing YBCO material on them, then patterning them by using ion-milling technique. Circuitizing washer-shape SQUIDs to possess a pair of step-edge junctions of 2-5$\mu$ line width with a high angle>$50^{\circ}C$ , we examined their I-V characteristics thoroughly and Shapiro steps clearly as we irradiate microwaves of 8-20 GHz frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.285-289
• /
• 2011

In this study, lead-free $(K_{0.5}Na_{0.5+X})(Nb_{0.96}Sb_{0.04})O_3+0.2mol%La_2O_3+1.2mol%$ $K_4CuNb_8O_{23}$ (X= 0~0.025) ceramics were fabricated by normal sintering method at $1060^{\circ}C$ for 5 h. Microstructures, piezoelectric and dielectric properties of specimens were investigated with special emphasis in the influence of Na excess addition. The grain size of specimen was slightly decreased with increasing Na content. In the 2 [mol%] Na excess addition of NKNS ceramics, density, electromechanical coupling factor, piezoelectric constant and electromechancal quality factor of specimen were found to reach the optimum values of 4.25 [$g/cm^3$], 0.4357, 154.43 [pC/N] and 580, respectively.

• Economic and Environmental Geology
• /
• v.25 no.1
• /
• pp.27-39
• /
• 1992

Several pyrophyllite deposits occur around the Milyang area where Cretaceous andesitic rocks and spatially related granitic rocks are widely distributed. Pyrophyllite ores consist mainly of pyrophyllite, and quartz with small amount of sericite, pyrite, dumortierite, and diaspore. The andesitic rocks and spatially related granitic rocks in this area suggest that they could be formed from the same series of a calc-alkaline magma series. The contents of $SiO_2$, $Al_2O_3$, LOI(loss on ignition) are enriched, and $K_2O$, $Na_2O$, CaO, MgO, $Fe_2O_3$ are depleted in altered andesitic rocks and ores. Enrichment of As, Cr, Sr, V, Sb and depletion of Ba, Cs, Ni, Rb, U, Y, Co, Sc, Zn are characteristic during mineralization. The pyrophyllite ores can be discriminated from the altered-and unaltered wall-rocks by an increasing of $(La/Lu)_{cn}$ from 4.18~22.13 to 8.98~55.05. In R-mode cluster analysis, Yb-Lu-Y, La-Ce-Hf-Th-U-Zr, $TiO_2-V-Al_2O_3$, Sm-Eu, $CaO-Na_2O-MnO$, Cu-Zn-Ag, $K_2O-Rb$ are closely correlated. In the discriminant analysis of multi-element data, $P_2O_5$, As, Cr and $Fe_2O_3$, Sr are helpful to identify the ores from the unaltered-and altered wall-rocks. In the factor analysis, the factors of alteration of andesitic rocks and ore mineralization were extracted. In the change of ions per unit volume, $SiO_2$, $Al^{3+}$ and LOI are enriched and $Na^+$, $K^+$, $Ca^{2+}$, $Mg^{2+}$, $Mn^{2+}$ and $Fe^{3+}$ are depleted during the alteration processes. The Milyang and the Sungjin pyrophyllite deposits could be mineralized by hydrothermal alteration in a geochemical condition of low activity ratio of alkaline ions to hydrogen ion with reference to spatially related granitic rocks.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.158-161
• /
• 2006

Superconducting YBCO films were successfully fabricated by MOD process using chemically modified precursor solution. In this study, a chemically modified precursor solution for MOD processing was synthesized using metal-organic salts and organic additives. It was shown that crack-free and uniform precursor films were formed after calcination in humidified Oxygen atmosphere. Less than 3 hours are required to finish the calcination process. XRD measurement shows that $BaF_2,\;CuO,\;Y_2O_3$ are major constituent of precursor films. Furthermore, YBCO films without any secondary phases were successfully fabricated after annealing in wet $Ar/O_2$ atmosphere. The YBCO film prepared on a $LaAlO_3$ single crystal substrate ($10mm{\times}10mm$) gives transport $I_c$ of 10A at 77K. This chemical modification approach is a possible candidate for improving MOD-processing of YBCO coated conductor.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.143-151
• /
• 2007

Accurate measurements of the microwave surface resistance (Rs) of high temperature superconductor (HTS) films are important with regard to applications of HTS materials for wireless communications. As the surface resistance values of HTS films are usually extracted from the measured unloaded quality factor ($Q_0$) of resonators made of HTS films, it is essential to measure the resonator $Q_0$ with accuracy. The $TE_{011}\;mode\;Q_0$ of sapphire resonators with the endplates made of $YBa_2Cu_3O_{7-{\delta}}$(YBCO) film on $LaAlO_3$ is measured by using the S-parameter circle-fit method at a frequency of about 19.6 GHz and temperatures of 30 K to 90 K, which is compared with the measured values by using the Lorentzian-fit method. Good agreements are found between the two sets of $Q_0$ values measured by using the two different methods whether the resonator is used in a weak-coupling scheme or a strong-coupling scheme, showing reliability of both methods fur measuring the resonator $Q_0$ accurately. The $Q_0$ of sapphire resonators with a gap between the top plate and the rest of the resonator is also discussed.