• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 환경생물
• /
• 제37권1호
• /
• pp.19-30
• /
• 2019

본 연구는 지리적인 이유로 부유생물 생태연구가 상대적으로 진행되지 않은 독도 주변 해역에서 계절적 환경 특성과 더불어 부유생물 식물플랑크톤 군집구조 변화 특성을 파악하고자 하였다. 본 해역에서 4계절 동안 총 4문 72종의 식물플랑크톤이 출현하였으며, 전 계절 평균 식물플랑크톤 현존량은 $2.38{\times}10^4cells\;L^{-1}$로 낮은 값을 보였다. 본 지역은 인류에 인한 오염이 전무한 곳이므로 섬연안임에도 외양과 같은 생태특성을 보였다. 동계에는 33종의 식물플랑크톤이 출현하였고, 전체 평균 식물플랑크톤 현존량은 $3.32{\times}10^4cells\;L^{-1}$으로 비교적 높은 현존량을 보였다. 종조성은 규조류 Chaetoceros lorenzianus, C. pseudocurvisetus 등이 우점하였다. 춘계는 15종의 식물플랑크톤이 출현하였으며, 평균 식물플랑크톤 현존량은 $1.04{\times}10^4cells\;L^{-1}$로 춘계임에도 매우 낮은 현존량을 보였다. 종조성은 다양한 종류의 nano-flagellate가 출현하였다. 하계 46종의 식물플랑크톤이 출현하였으며, 식물플랑크톤 현존량은 $0.28{\times}10^4cells\;L^{-1}$로 낮았으며, Chaetoceros spp., Guinardia striata, Rhizosolenia spp., Skeletonema spp.가 출현하였다. 추계는 57종으로 가장 다양한 식물플랑크톤이 출현하였으며, 전 수층의 평균 식물플랑크톤 현존량은 $4.86{\times}10^4cells\;L^{-1}$, 규조류 Pseudo-nitzschia spp.가 크게 번무하여 4계절 중 가장 높은 생산력을 보였다. 또한, 종조성에서 특이적으로 열대 지표종인 와편모조류 Amphisolenia sp.와 Ornithocercus magnificus가 출현하여, 쓰시마난류가 추계에 강하게 유입된 것을 시사할 뿐만 아니라, 이들의 출현으로 과거에 비해 해류와 기후가 변화한 사실을 유추해 볼 수 있다. 따라서 독도의 지속가능한 이용을 위해서 독도를 중심으로 지속적인 물리-화학적 연구와 함께 생물학적 연구를 실시하여 독도 연안 생태계 변화 추이를 장기간 관찰할 필요가 있다.

• 한국해양학회지
• /
• 제30권2호
• /
• pp.91-115
• /
• 1995

동해에서의 해양-대기 열교환량을 1961년부터 1990년까지의 선상관측자료와 1976 년부터 1985년까지의 일본기상처 부표자료를 이용하여 구하였다. 그리고 이 결과와 해 양상층부 200m 내의 열용량의 계절변화로부터 해양내부의 열유동량을 계산하였다. 겨 울에는 유입되는 단과복사량과 방출되는 장파오복사량의 크기가 비슷해 복사에 의한 열방출량은 적지만 열속과 자멸속이 강하여 전 해역에서 대기로 많은 열량을 방출한 다. 유효열방출량의 공간적인 변화폭은 100 Wm/SUP -2/이상이며, 최대의 열방출량은 쓰가루해협 부근에서 일어나고 대한해협과 울릉분지역등 남부역이 높은 방출량이 나타 난다. 특히 남서 해역의 강한 열방출이 겨울에 동해 중층균실수의 형성에 영향을 주는 것으로 보인다. 여름에는 강한 태양복사와 낮은 난류속의 영향으로 전해역에서 120~ 140 Wm/SUP -2/의 비슷한 크기로 해양이 가열된다. 해양내부의 열유동은 일본연안에서 양의 값을 나타내 여름의 강한 대마난류에 의한 열량의 유입을 보이며, 그 크기는 해 면을 통해 흡수한 열량보다 커서 여름에는 대마난류에 의한 열유입이 중요함을 보여준 다. 한국연안에서는 음의 값으로 수온이 낮은 북한 한류계수의 남하를 나타낸다. 봄과 가을은 3월과 100월에 각각 최소, 최대를 나타낸다. 유효열교환량의 연변화폭은 남서 해역의 경우 약 580 Wm/SUP -2/이다. 해표면을 통한 연평균 유효열교환량은 모든 해역 에서 음의 값으로 대기중으로 열량을 방출하며, 그 크기는 쓰가루해협부근에서 -130 Wm/SUP -2/로 강하고 대한해협과 울릉분지역에서도 이웃하는 해역보다 많은 열량을 방 출한다. 위도 35$^{\circ}$~39$^{\circ}$N 사이에서의 공간적인 연평균값의 크기는 단파복사량, 자멸 속, 장파복사, 열속의 크기로 각각 129, -90, -58, -32Wm/SUP -2/으로 유효열교환량은 -51W/SUP -2이다.

• 한국산림과학회지
• /
• 제66권1호
• /
• pp.16-36
• /
• 1984

화강암질풍화토(花崗岩質風化土)의 미교란(未攪亂) 시료(試料)를 사용하여 일면(一面) 직접(直接) 전단시험(剪斷試驗)으로 측정(測定)한 전단강도(剪斷强度)와 함수비(含水比), 간극비(間隙比), 건조밀도(乾燥密度), 비중(比重)과의 관계(關係)를 통계(統計) 분석(分析)하였고, 화강암질풍화토(花崗岩質風化土)의 사방시공지(砂防施工地)에 식재(植栽)된 리기다소나무림(林)과 리기테-다소나무림(林)에서 토양단면(土壤斷面)을 만들어 산중식토양경도계(山中式土壤硬度計)로 토양(土壤)의 견밀도(堅密度)를 측정(測定)하고 수근분포(樹根分布)를 조사(調査)하여 통계(統計) 분석(分析)한 결과(結果) 다음과 같다. 1) 함수비(含水比), 간극비(間隙比)와 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 2) 건조밀도(乾燥密度)와 전단강도(剪斷强度) 사이에는 정(正)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 3) 비중(比重)과 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 상관관계(相關關係)를 인정(認定)할 수 없었다. 4) 전단강도(剪斷强度)에 영향(影響)을 미치는 영향요소(影響要素)의 직접효과(直接效果)의 크기는 함수비(含水比)>간극비(間隙比)>건조밀도(乾燥密度)의 순위(順位)이다. 5) 다중선형(多重線型) 회귀방정식(回歸方程式)의 분산분석결과(分散分析結果) 함수비(含水比)만이 회귀성(回歸性)이 인정(認定)되므로 함수비(含水比)를 독립변수(獨立變數)로 하여 전단강도(剪斷强度)를 추정(推定)하기 위한 회귀방정식(回歸方程式)은 제한(制限)된 건조밀도(乾燥密度)의 범위내(範圍內)에서 적합도(適合度)가 매우 높게 평가(評價)되었다. 6) 토양(土壤)의 견밀도(堅密度)는 토심(土深)이 깊어짐에 따라 높아진다. 7) 토양(土壤)의 지표경도(指標硬度)와 수근수(樹根數) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 8) 리기다소나무와 리기테-다소나무의 수근(樹根)은 토심(土深) 20cm까지에 대부분 분포(分布)하고 있었다. 9) 리기다소나무림(林)과 리기테-다소나무림(林)에서 측정(測定)한 토양(土壤)의 지표경도(指標硬度)를 독립변수(獨立變數)로한 회귀방정식(回歸方程式)으로 수근수(樹根數)를 추정(推定)할 수 있었으나 낮은 적합도(適合度)를 나타내었다.

• 한국토양비료학회지
• /
• 제5권2호
• /
• pp.1-38
• /
• 1972

우리나라 답토양(畓土壤)에 대(對)한 토지(土地)의 합리적(合理的) 이용(利用), 토지기반조성(土地基盤造成) 및 생산성 향상(向上) 그리고 토양(土壤)에 관(關)한 조사연구(調査硏究)의 방향(方向)을 뒷받침하기 위(爲)하여 김제만경평야(金堤萬頃平野)에 분포(分布)하고 있는 답토양(畓土壤)에 대(對)한 형태(形態) 및 이화학적(理化學的) 특성(特性) 그리고 그와 수도수량(水稻收量)과의 관계(關係)를 구명(究明)하고 이를 기초(基礎)로 하여 답토양(沓土壤)의 분류법(分類法)과 적성등급구분(適性等級區分)을 시안(試案)하였는 바 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 답토양(畓土壤)의 형태(形態), 이화학적(理化學的) 특성(特性) 및 그와 수도수량(水稻收量)과의 관계(關係) 김제(金堤) 만경평야(萬頃平野)에 분포(分布)하고 있는 15개(個) 답토양통(畓土壤統)에 대(對)하여 이들 토양(土壤)의 형태(形態), 이화학적(理化學的) 특성(特性)을 보면 다음과 같다. 토양단면(土壤斷面)의 발달정도(發達程度)를 보면 공덕(孔德), 김제(金堤), 만경(萬頃), 백구(白鷗), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)는 B(Cambic B)층(層)이 있고 극락(極樂)과 화동통(華東統)은 Bt(Argillic B)층(層)이 있으나 광활(廣活), 신답(新踏) 및 화계통(華溪統)에는 B층(層) 혹(或)은 Bt층(層)이 없다. 특(特)히 공덕(孔德) 및 봉남통(鳳南統)은 흑니층(黑尼層)이 심토(心土) 하부(下部)에 개재(介在)되여 있다. 토양단면(土壤斷面)의 토색(土色)을 보면 공덕(孔德), 광활(廣活), 백구(白鷗) 및 신답통(新踏統)은 대체(大體)로 청회색(靑灰色), 암회색(暗灰色)을 띄우고 김제(金堤), 만경(萬頃), 봉남(鳳南), 부용(芙蓉), 수암(水岩), 전북(全北), 지산(芝山) 및 호남통(湖南統)은 회색(灰色), 회갈색(灰褐色)을 띠우며 극락(極樂), 화계(華溪) 및 화동통(華東統)은 표토(表土) 및 표토하부(表土下部)의 회색(灰色)을 제외(除外)하고 황갈색(黃褐色), 갈색(褐色)을 띠운다. 토양단면(土壤斷面)의 토성(土性)을 보면 공덕(孔德), 극락(極樂), 김제(金堤), 봉남부용(鳳南芙蓉), 호남(湖南) 및 화동통(華東統)은 식질(埴質)이고 백구(白鷗), 전북(全北) 및 지산통(芝山統)은 식양질(埴壤質) 혹은 미사식양질(微砂埴壤質)이며 광활(廣活), 만경(萬頃) 및 수암통(水岩統)은 미사사양질(微砂砂壤質) 그리고 신답(新踏) 및 화계통(華溪統)은 사질(砂質) 혹은 석력사질(石礫砂質)이다. 표토(表土)의 탄소함량(炭素含量)은 0.29%~2.18% 범위(範圍)에 있으나 1.0~2.0%인 것이 많으며 표토(表土)의 전질소함량(全窒素含量)은 0.03%~0.24% 범위(範圍)에 있다. 이들은 심토(心土) 혹은 기층(基層)으로 갈수록 감소(減少)되는 경향(傾向)이나 불규칙적(不規則的)이다. 표토(表土)의 탄질비(炭窒比)는 4.6~15.5 범위(範圍)인데 8~10인 것이 많으며 심토(心土) 및 기층(基層)에서는 표토(表土)에 비(比)하여 그 범위(範圍)가 커서 3.0~20.25이다. 토양반응(土壤反應)은 pH4.5~8.0 범위(範圍)에 있으나 광활(廣活) 및 만경통(萬頃統)을 제외(除外)하고는 모두 산성(酸性)이다. 염기치환용량(鹽基置換容量)은 표토(表土)에서는 5~13 me/100g 범위(範圍)이며 심토(心土) 및 기층(基層)에서는 사질토양(砂質土壤)을 제외(除外)하고 모두 10~20 me/100g 범위(範圍)에 있다. 염기포화도(鹽基飽和度)는 공덕(孔德) 및 백구통(白鷗統)을 제외(除外)하고는 모두 60% 이상(以上)이다. 표토(表土)의 활성철함량(活性鐵含量)은 0.45~1.81% 범위(範圍)이고 역환원성(易還元性)망간은 15~148ppm 범위(範圍)이며 유효규산은 36~366ppm 범위(範圍)에 있다. 이들 3성분(成分)의 용탈(溶脫) 및 집적(集積)은 토양배수(土壤排水), 토성조건(土性條件)에 따라 다르지만 대체(大體)로 10~70cm 범위(範圍)에 집적(集積)하고 있으나 규산(珪酸)은 경우(境遇)에 따라 철(鐵), 망간 보다 깊은 층위(層位)에 집적(集積)되여 있다. 각(各) 토양통(土壤統)의 주요특성(主要特性)은 해안(海岸)에서 부터 거리에 따라 점변(漸變)하고 있으며 점토(粘土), 유기탄소(有機炭素) 및 pH는 해안(海岸)으로 부터 내륙(內陸)으로 옮겨가는 거리와 다음과 같은 상관(相關)이 있다. y(표상(表上)의 점토함량(粘土含量)) = $$-0.2491x^2+6.0388x-1.1251$$ y (심토(心土) 및 표토하부(表土下部)의 점토함량(粘土含量)) = $$-0.31646x^+7.84818x-2.50008$$ y(표토(表土)의 유기탄소함량(有機炭素含量)) = $$-0.0089x^2+0.2192x+0.1366$$ 로서 내륙(內陸)으로 갈수록 높아지는 경향(傾向)이며 y(심토(心土) 및 표토하부(表土下部)의 pH) = $$0.0178x^2-0.4534x-8.353$$ 로서 내륙(內陸)으로 갈수록 낮다. 토양(土壤)의 형태(形態) 및 이화학적(理化學的) 특성(特性)에 있어 특기(特記)되는 것은 토양(土壤)의 발달도(發達度), 토색(土色), 모재(母材)의 다원적(多元的) 퇴적(堆積), 유기물층(有機物層)의 개입(介入), 토성(土性) 및 토양반응(土壤反應) 등(等)이였으며 이들은 답토양(畓土壤)의 분류(分類)에서 고려(考濾)되여야 할 사항(事項)이였다. 토양(土壤)의 몇가지 특성(特性)과 수도수량(水稻收量)과의 관계(關係)에서 토양배수(土壤排水)가 약간양호(若干良好) 내지(乃至) 불량(不良)한 식질토(埴質土), 양질토(壤質土) 그리고 유효심도가 낮은(50cm) 식질토(埴質土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg 이상(以上)이며 사질토(砂質土), 배수(排水)가 양호(良好)한 식질토(埴質土), 유효심도가 낮은 양질토(壤質土) 및 함염토(含鹽土)들은 수량(收量)이 대부분(大部分) 10a당(當) 375kg미만(未滿)이다. 수도수량(水稻收量)에 영향(影響)을 미치는 토양(土壤)의 형태적(形態的) 특성(特性)은 토양배수(土壤排水), 토성(土性), 유효심도, 표토(表土) 및 표토하부(表土下部)의 회색화(灰色化) 그리고 염농도(鹽濃度) 등(等)이며 이들은 답토양(畓土壤)의 적성등급구분(適性等級區分)에서 고려(考慮)되여야 할 사항(事項)이였다. 2. 답토양(畓土壤)의 분류(分類) 및 적성등급구분(適性等級區分) 답토양(畓土壤)의 분류기준(分類基準)은 토양(土壤) 자체(自體)가 가지고 있는 성질(性質)에 근거(根據)를 두었다. 토양분류단위(土壤分類單位)는 토양대군(土壤大群), 토양군(土壤群), 토양아군(土壤亞群), 토양계(土壤系) 그리고 토양통(土壤統)의 5단계(段階)를 두고 분류(分類)의 기본(基本) 단위(單位)는 토양통(土壤統)으로 하였다. 토양분류(土壤分類)에 있어 형태적(形態的) 특성(特性)의 차이(差異)를 결정(決定)하기 위(爲)하여 2종류(種類)의 특징토층(特徵土層) 즉(卽) 숙성토층(熟成土層) 및 반숙토층(半熟土層)을 설정(設定)하여 이들의 유무(有無) 및 종류(種類)를 토양대군(土壤大群)의 분류기준(分類基準)으로 하였다. 토양군(土壤群) 및 토양아군(土壤亞群)의 분류(分類)에 있어 고려(考慮)되여야 할 특징적(特徵的) 토양특성(土壤特性)은 우선(于先), 토색(土色), 염농도(鹽濃度), 표토(表土) 및 표토(表土) 하부(下部)의 회색화(灰色化), 토사(土砂)의 다원적(多元的) 퇴적(堆積) 그리고 유기물층(有機物層)의 개입(介入)으로 하였으며 토양계(土壤系)의 분류(分類)에서 고려(考慮)한 토양특성(土壤特性)은 토양반응(土壤反應), 토성(土性) 및 석력함량(石礫含量)에 근거(根據)를 두어 분류(分類)하는 한편 이들에 대(對)한 정의(定義)를 내렸다. 그리고 필자(筆者)의 시안(試案)과 기존(旣存)의 분류안(分類案)을 상호비교(相互比較)하여 검토(檢討)하였다. 답토양(畓土壤)의 적성등급구분(適性等級區分)은 인위적(人爲的) 작용(作用)에 의(依)한 가변성(可變性)이 적은 토양특성(土壤特性)을 토대(土臺)로 하였으며 등급구분단위(等級區分單位)는 등급(等級) 및 아급(亞級)의 2단계(段階)를 두었다. 등급(等級)은 토양(土壤)의 잠재생산력(潛在生産力)이 어느 주어진 단위(範圍)에서 같고 토지이용(土地利用) 및 관리(管理)의 난이(難易)를 고려(考慮)한 토양조건(土壤條件)에 따라 1급(級)에서 4 급지(級地)까지의 4 등급(等級)으로 구분(區分)하였고 아급(亞級)은 동일등급내(同一等級內)에서 중요(重要)한 제한인자(制限因子)로 하였으며 그 인자(因子)는 경사(傾斜), 저염(低濕), 사질(砂質) 석력(石礫), 염해(鹽害), 미력(美熟)이다. 이들 등급(等級) 및 아급(亞級)을 각각(各各) 정의(定義)를 하였으며 아울러 분류시안(分類試案)과의 연관성(連關性)을 검토(檢討)하였다. 김제(金堤) 만경평야(萬頃平野)의 15개(個) 답토양통(畓土壤統)의 분류(分類) 및 적성등급(適性等級) 구분시안(區分試案)을 종합(綜合)하여 보면 다음과 같다.