• 한국재료학회지
• /
• 제14권3호
• /
• pp.224-228
• /
• 2004

Respectively the powder made of ZnO added $SnO_2$ was prepared by coprecipitation method and the thick film gas sensor was fabricated by screen-printing technique, The morphology and phase of the powder and film was investigated by SEM and XRD. The specific area of the particle was linearly increased with ZnO contents. Target gas was di(propylene glycol) methylether ($CH_3$($OC_3$$H_{6}$ )$_2$OH, DPGME), which is simulant gas of blister gas. The gas sensing characteristics for DPGME were examined with flow type measurement system and the concentrations of target gas were controlled from 500 ppb to 1500 ppb. ZnO (2 wt%) added $SnO_2$ showed maximum sensitivity to DPGME at $300^{\circ}C$.

• 한국생활과학회지
• /
• 제8권1호
• /
• pp.151-163
• /
• 1999

The purpose of this study was to investigate the thermal resistance and the liquid/vapor water transfer characteristics of four waterproof and water vapor permeable coated fabrics with the ground fabric called nylon taffeta. In order to establish the experimental environment, outdoor temperature and humidity in Taegu during the last three years were examined and the experiment was performed at (1) $15^{\circ}C$, 50% R.H., (2) $20^{\circ}C$, 60% R.H., (3) $25^{\circ}C$, 65% R.H., which were the average standards in spring and fall. The test results were as follows ; 1. Among physical parameters, the thinner the thickness was, the higher the water vapor permeability was. But the porosity in thickness was not proportional to water vapor permeability linearly. 2. The thicker the thickness of specimens was and the smaller the bulk density and porosity were, the higher the thermal resistance. And the results also shown that the larger the temperature difference between the environmental temperature and the hot plate was, the more the difference of CLO values was apparent. 3. Since the contact angle of all specimens are above $90^{\circ}$, the all specimens have a good performance in waterproof. The more the specimens surface were rough, the higher the thermal resistance was. 4. According to the result of performing moisture transfer test using the simulating body skin-clothing-environment system, the humidity sensor placed in between the fabric and the environment detected the full saturation in 10 minutes after the experiment had began at $15^{\circ}C$, 50% R.H. and in 15 minutes after the experiment both at $20^{\circ}C$, 60% R.H. and at $25^{\circ}C$, 65% R.H. 5. ${\Delta}$ values of the humidity sensors placed in between the human body and the fabric and in between the fabric and the environment fluctuated repeatedly within the range of $20{\sim}40%$ at $20^{\circ}C$, 60% R.H., and $15{\sim}30%$ at $25^{\circ}C$, 65% R.H.

• Tribology and Lubricants
• /
• 제26권2호
• /
• pp.97-104
• /
• 2010

A new magnetoelastic technique of oil viscosity measurement, where the oil viscosity is estimated by frequency shift of natural oscillations of magnetoelastic ribbon, is implemented in this study. Laboratory tests of the detector prototype are performed for measurement of viscosity of base synthetic and mineral oils. It was found that measurement accuracy was better when damping factor was estimated in comparison with accuracy of frequency of damped oscillations. Thus the oil viscosity was calibrated as a function of number of pulses of the damped oscillations of magnetoelastic ribbon. Result generally showed that developed detector is promising for in line oil viscosity measurement in wide viscosity range from 10 cSt up to 600 cSt, while the viscosity measurement was relatively instable when the viscosity of test oil was over 400 cSt.

• 한국식품과학회지
• /
• 제29권6호
• /
• pp.1119-1124
• /
• 1997

과채류의 수파 후 저장에 있어서 중요한 생리적 지표가 되는 호흡속도를 마이크로컴퓨터와 압력센서 (MPX-10-DP, Motorola)를 사용하여 종래의 마노메타법의 문제점인 수증기압을 보정하여 간편하고 신속하게 측정할 수 있는 방법에 관해 연구하였다. 과채류 호흡속도 계측 중 각 온도구간에서 호흡속도 계측용기 내의 온도 변화는 ${\pm}0.5^{\circ}C$이었다. 수식화한 습윤도표를 이용하여 호흡속도 측정용기 내의 수증기압을 환산한 결과 실험초기에 수증기압이 일시적으로 상승한 추 방치시간동안은 일전한 수증기압을 유지하였으며 , $CO_2$, scrubber 가동 후에는 수증기압이 급격히 감소하는 경향을 나타내었다. 저장용기 내부의 전체 상대압력에서 수증기압이 차지하는 비율은 $1^{\circ}C$에서 $33{\sim}46%$, $11^{\circ}C$에서 $23{\sim}45%$, $21^{\circ}C$에서 $35{\sim}53%$로 각 실험온도 구간에서 거의 일정한 비율을 나타내었다. PVM으로 구한 호흡속도와 GC를 이용하여 측정한 값과의 차이는 $1^{\circ}C$에서 $0.8{\sim}1.2\;mgCO_2kg^{-1}h^{-1}$, $11^{\circ}C$에서 $3.9{\sim}11.0\;mgCO_2kg^{-1}h^{-1}$, $21^{circ}C$에서 $8.0{\sim}32.0\;mgCO_2kg^{-1}h^{-1}$의 차이를 나타내었다. CPVM으로 구한 호흡속도와 GC를 이용하여 측정한 값은 $1^{\circ}C$에서 $0.2{\sim}O.3\;mgCO_2kg^{-1}h^{-1}$, $11^{\circ}C$에서 $0.2{\sim}2.9\;mgCO_2kg^{-1}h^{-1}$, $21^{\circ}C$에서 $1.0{\sim}9.0\;mgCO_2kg^{-1}h^{-1}$, 차이를 나타내었다. CPVM으로 구한 호흡속도가 PVM으로 구핀 값보다 GC로 계측한 값과의 편차가 적은 것으로 나타나, 이 방법을 이용하면 보다 간편하고 정확하게 과채류의 호흡속도를 계측할 수 있음을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.778-781
• /
• 2002

MI(Magneto-Impedance) sensor which is made by thin films has significantly high detecting sensitivity in weak magnetic field. It also has a merit to be able to build in the low power system. Its structure is simple, which makes it easier to prepare a miniature. In this study, its magnetic permeability and anisotropy field$(H_k)$ as a function of a thickness of sputtered amorphous CoZrNb films with zero-magnetostriction and excellent soft magnetic property are investigated. In order to make a uniaxial anisotropy, film was subjected to the post annealing in a static magnetic field with 1KOe intensity at 250, 300, and $320^{\circ}C}$ respectively for 2 hours. Anisotropy field$(H_k)$ of film is measured by using a MH loop tracer. Its magnetic permeability of a film is measured over the frequency range from 1 MHz to 750MHz. It has shown that the magnetic permeability of amorphous CoZrNb film is decreased due to the skin effect with increasing a thickness of the CoZrNb film, and hence its driving frequency is lowered. And, it was examined on the permeability and impedance to fabricate the MI sensor which acts at a low frequency by thickening a CoZrNb film relatively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2135-2137
• /
• 2005

This paper describes the features of electric and magnetic fields produced by lightning discharges. The measuring system consists of fast electric field sensor, crossed-loop magnetic field sensors, signal processing circuit, A/D converter and data acquisition equipment with a 12bit resolution and 10[MS/s] sampling rate. The frequency bandwidth and responsitivity of the electric field measuring system were 40[Hz]${\sim}$2.6 [MHz] and 2.08 (V/m/mV) and those of the magnetic field measuring system were 400[Hz]${\sim}$1[MHz] and 2.78[nT/mV], respectively. The electric and magnetic fields produced by lightning discharges were observed, and the features and parameters of the waveforms were analyzed.

• 한국결정학회지
• /
• 제8권1호
• /
• pp.38-47
• /
• 1997

새로운 방식의 결정성장용 직경 자동제어장치를 개발하였다. 이 장치는 금속선의 장력 변화를 주파수로 변환시켜 감지하는 무게센서로서 신호전달 및 전력공급 체계가 무접촉 방식이므로 노이즈가 극소화되며 따라서 안정성, 정밀성이 종래의 센서에 비해 10배 이상 증대된다. 이 장치에서 무게센서 부분은 1) 금속선, 2) 시그날을 형성하는 Sinusoidal Wave Generator, 3) 형성된 시그날의 진폭을 조정하고 안정화 시켜주는 자동 증폭조절회로, 4) 정류장치 및 신호 변환기, 5) 시그날을 관리, 제어하는 PC 보드 등으로 구성하였고, 그 외에 2개의 검증용, 무게보정용, 성장제어용 등 4개의 프로그램을 작성하였다. 이 장치는 표준편차 값이 $\pm0.10g$(1회/sec 측정 때), 분해능이 $5{\times}10^{-5}$이고, 최대 200kg까지 결정을 성장시킬 수 있으며, 또한 압력조건은 진공조건부터 200 atm 이하, 온도조건은 $350^{\circ}C$ 이하에서 일관성, 재현성 있는 작동이 가능했다. 단결정 자동직 경제어에 필요한 정확도를 확보하기 위해 온도범위 $100^{\circ}C$가 $\pm0.025^{\circ}C$로자동 조절되도록 '시그날 Divider'를 제작하였다. 이 무게 센서를 $Y_3Sc_2Ga_3O_{12},\;Er-Y_3Sc_2Al_3O_{12},\;Bi_{12}GeO_{20}$ 등의 단결정 성장에 응용하였으며 매우 양호한 결정을 성공적으로 성장시킬 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제34권11호
• /
• pp.3307-3311
• /
• 2013

A new fiber optical sensor was developed for the determination of 2,4-dichlorophenol (DCP). The sensor was based on DCP oxidation by oxygen with the catalysis of iron(III) tetrasulfophthalocyanine (Fe(III)PcTs). The optical oxygen sensing film with $Ru(bpy)_3Cl_2$ as the fluorescence indicator was used to determine the consumption of oxygen in solution. A lock-in amplifier was used for detecting the lifetime of the oxygen sensing film by measuring the phase delay change of the sensor head. The different variables affecting the sensor performance were evaluated and optimized. Under the optimal conditions (i.e. pH 6.0, $25^{\circ}C$, Fe(III)PcTs concentration of 0.62 mg/mL), the linear detection range and response time of the sensor are $1.0{\times}10^{-6}-9.0{\times}10^{-6}$ mol/L and 250 s, respectively. The sensor displays high selectivity, good repeatability and stability, and can be used as an effective tool in analyzing DCP concentration in practical samples.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1162-1164
• /
• 1995

In this paper, $TiO_2$-xmol%$V_2O_5$, x=0.0, 1.0, 2.0, 3.0 specimens are fabricated by Sol-Gel method. For the improvement of humidity sensitive characteristics for specimens, their microstructures are analysed and the optimum processing condition is established. Grain size increases with substitution rate of $V^{5+}$, on $Ti^{4+}$ site. Their humidity sensitive characteristics is good at 1mol% of $V_2O_5$ rate and heat-treated at $700^{\circ}C$. The capacitance of specimens decreases with frequency.

• 한국전기전자재료학회논문지
• /
• 제22권12호
• /
• pp.1089-1094
• /
• 2009

Carbon nanotubes (CNTs) have excellent electrical, chemical stability, mechanical and thermal properties. In this paper, networks of Multi-walled carbon nanotube (MWCNT) materials were investigated as resistive gas sensors for ethanol ($C_2H_5OH$) detection. Sensor films were fabricated by air spray method for the multi-walled CNTs solution on glass substrates. Sensors were characterized by resistance measurements in the sensing system, in order to find the optimum detection properties for the ethanol gas molecular. The film that was sprayed with the MWCNT dispersion for 60 see, was 300 nm thick. And the electric resistivity is $2{\times}10^{-2}\;{\Omega\cdot}cm$. Also, the sensitivity and the linearity of MWVNT sensor for ethanol gas are 0.389 %/sec and 17.541 %/FS, respectively. The MWCNT film was excellent in the response for the ethanol gas molecules and its reaction speed was very fast, which could be using as ethanol gas sensor. The conductance of the fabricated sensors decreases when the sensors are exposed to ethanol gas.