• Proceedings of the Korea Database Society Conference
• /
• 2010.06a
• /
• pp.33-41
• /
• 2010

Recently the number of IT equipment have increased. It consumes large amounts of energy and is emissions of greenhouse gases. Co2 emissions with the PC and the monitor has the highest percentage to 39% more than other IT equipment. In addition, Plan for your PC's power management and technology development is being pursued in developed countries. To reduce energy costs of organizations with large numbers of the PC and to cut down on Co2 emissions, the energy load control technology of ACPI standards-based PC IS suggested. AMI-based PC power-management system was constructed, Approximately 20% of operating a result of the test power consumption was reduced. Looking at the case of the United States, PC monitors from the University of Wisconsin-Oshkosh was Sleep mode. As a result, the monitor on a, $ 20 for a year reduced energy costs. In GE(General Electronic), Approximately 75,000 PC's power setting time was Monitor Off :15 minutes/ Hard Drives Off 30 minutes/ System Standby 30 minutes/ Hibernation mode 2 hours. 1 year, electric bill was $ 2.5 million savings and 3 years electric bill was $ 6.5 million savings. Measuring energy usage data, using the measured data, electric energy management technology is not. Platform development to measure energy usage for Individual energy-consuming equipment is urgently required.

• Journal of Biosystems Engineering
• /
• v.27 no.4
• /
• pp.311-316
• /
• 2002

This study was carried out to investigate the optimum operating conditions of the air injection type onion peeling device which could be attached to a prototype onion peeler. An onion, stem and root was cut and some vertical line was dug in 1 mm depth on the skin, was put on the two parallel rollers. The diameters of the rollers were 105 mm and the ratio of peripheral velocity was 3:2, and moved by a geared motor. Air from the nozzle with high pressure and velocity was jetted to the rotating onion on the revolving rollers, and then the skin of the onion was stripped. On the test, the rolling characteristics of the experimental materials were measured. The effective peeling conditions were, the number of digging line on the skin of the onion was 4, and the air jet pressure was above 392.3 kPa(4.0 kg/$\textrm{cm}^2$) when the peripheral velocity was at 2.4 m/s. On these conditions, time requirement to peel an onion was less than 2 sec.

• Journal of Bio-Environment Control
• /
• v.13 no.4
• /
• pp.266-270
• /
• 2004

A rose factory type is a system that enables year-round, planned and mass production of high quality cut-rose. Conversion of a conventional system to a rose factory is essential to increase cut-rose export. Controlling root Bone in culled rose production factory is very important for economic and efficient production of rose. This study was conducted to determine optimum root zone temperature of nutrient solution in single-stemmed rose production system. The optimum temperature of the nutrient solution for growth, photosynthetic and transpiration rates for 'Red Velvet' was $15\~20^{\circ}C$. Whereas the optimum temperature for 'Vital' was $10\~15^{\circ}C$. However, growth was almost sloped at $30^{\circ}C$, resulting in concluding the adaptation of 'Vital' to high temperature was poor as compared with 'Red Velvet'.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.99-106
• /
• 2013

DME (Di-Methyl Ether) is synthetic product that is produced through dehydration of methanol or a direct synthesis from syngas. And it is able to save fossil fuel and reduce pollutants of emission such as PM and $CO_2$. In spite of its advantages it is difficult to design DME fuelled engine system because DME fuel may cause to severely generate cavitation and corrosion in fuel delivery system due to physical properties of DME. Therefore, in this study three-dimensional internal flow characteristics with consideration of cavitation were predicted in the DME injector using diesel and DME fuel. Moving grid technique was employed to describe needle motion and 1-D hydraulic simulation of injector was also simulated to obtain transient needle motion profiles. The results of simulation show that cavitations was generated at the inlet of nozzle near high velocity region both diesel and DME. And mass flow rate of DME is reduced by 4.73% compared to that of diesel at maximum valve lift because cavitation region of DME is much more larger. To increase flow rate of DME injector, internal flow simulation has been conducted to investigate the nozzle hole inner R-cut effect. The flow rates of diesel and DME increase as R-cut increases, and flow coefficient of DME fuel injector was increased by 6.3% on average compared with diesel fuelled injector. Finally, optimum shape of DME injector nozzle is suggested through the comparison of flow coefficient with variation of nozzle hole inner R-cut.

• Journal of Food Hygiene and Safety
• /
• v.37 no.5
• /
• pp.306-309
• /
• 2022

Probiotics are live microorganisms that confer health benefits onto the host when administered at adequate doses. Most widely used probiotics, such as lactobacilli and bifidobacteria, are known to be elements of healthy gut microflora and hence are not considered a threat to the host. However, probiotics may pose a risk in certain populations with compromised immune systems or defects in gut barrier functions. Herein, we evaluated the safety of Bifidobacterium breve BB077, according to the safety evaluation guidelines for probiotics produced by the National Institute of Food and Drug Safety Evaluation (NIFDS). The results show that B. breve BB077 is both non-hemolytic and non-cytolytic. In contrast, B. breve BB077 exhibited higher streptomycin and tetracycline resistance than the suggested NIFDS standard cut-off values. Hence, a genetic analysis of the streptomycin and tetracycline resistance genes was performed to determine the origin of antimicrobial resistance. Streptomycin and tetracycline resistance was shown have arisen from chromosomal mutations and considered intrinsic to the taxonomic group. In conclusion, the B. breve BB077 strain might be safe for human consumption.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.428-432
• /
• 1999

As metallic surface has its unique lustrous appearance and optical reflectance in visible range of light, the metallization of plastic surface has been an essential drive toward weight reduction for fuel economy and decorations in transportation industry and has been put into practiced from wet chemical-electrochemial to dry vacuum process in view of an environmental effect. Electron-beam metallization was used in this work with an aim at improving the scratchproof surface hardness of plastic substrate with metallic finish character. Thin film of Al ($1000\AA$) and $SiO_2$($7000\AA$) were metallized on substrate of PC and PMMA and the films were evaluated by pencil test for surface hardness and by cross-cut tape test for adhesion. The ion beam treatment improved around twice as hard as non-treat surface. The ion beam is effect on its hardness and adhesion to surface hardened PC substrate.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.140-144
• /
• 2014

Co-(0.7 wt%) and Pr-(2.0, 3.5 or 5.0 wt%) doped cubic zirconia ($ZrO_2:Y_2O_3=50:50wt%$) single crystals grown by a skull melting method were heat-treated in $N_2$ at $1150^{\circ}C$ for 5 hrs. The brown colored as-grown single crystals were changed into either dark brownish green, greenish blue and light green color after the heat treatment. Before and after the heat treatment, the YSZ (yttria-stabilized zirconia) single crystals were cut for wafer form (${\phi}7.5mm{\times}t3mm$). The optical and structural properties were examined by UV-VIS spectrophotometer and X-ray diffraction. Absorption by $Co^{2+}$(${\fallingdotseq}589nm$: ${\Gamma}_8[^4A_2(^4F)]{\rightarrow}{\Gamma}_8+{\Gamma}_7[^4T_1(^4F)]$, ${\fallingdotseq}610nm$: ${\Gamma}_8[^4A_2(^4F)]{\rightarrow}{\Gamma}_8[^4T_1(^4F)]$], ${\fallingdotseq}661nm$: ${\Gamma}_8[^4A_2(^4F)]{\rightarrow}{\Gamma}_6[^4T_1(^4F)]$]) and $Pr^{3+}$(${\fallingdotseq}450nm$: ${^3}H{_4}-{^3}P{_2}$, ${\fallingdotseq}473nm$: ${^3}H{_4}{\rightarrow}{^3}P{_1}$, ${\fallingdotseq}484nm$: ${^3}H{_4}{\rightarrow}{^3}P{_0}$), change of ionization energy and lattice parameter were confirmed.

• Transactions of the KSME C: Technology and Education
• /
• v.3 no.2
• /
• pp.141-148
• /
• 2015

In this study, the VCB(Vacuum Circuit Breaker) has been developed using the Recurdyn that is widely used on multibody dynamics analysis. The VCB consists of three main circuits with the VI(Vacuum Interrupter) and the main frame with the operating mechanism. This analytic model is validated by comparing the simulation results and the experimental results. Generally, in order to reliably cut off the breaking current, the opening speed of the VCB after contact separation has to be a 0.9~1.1m/s. Therefore, the study of the design parameters of the VCB is needed. To improve the opening velocity, Taguchi design method is applied to optimize the design parameters of a VCB with a lot of linkages. In addition, to evaluate the improvement of the operating characteristics, the simulation results are compared with the Recurdyn and experimental results with improved prototype sample.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.3
• /
• pp.35-42
• /
• 2004

This research describes that the cutting characteristics and tool wear behavior in the micro cutting of three kinds of wear resistant cemented carbides (WC-Co; V40, V50 and V60) using PCD (Poly Crystalline Diamond) and PCBN (Poly crystalline Cubic Boron Nitride) cutting tools by use of the SEM (Scanning Electron Microscope) direct observation method. The purpose of this research is to present reasonable cutting conditions from the viewpoint of high efficient cutting refer to a precise finished surface and tool wear. Summary of the results is as follows: (1) The cutting forces tend to increase as the increase of the weight percentage of WC particles, and the thrust forces was larger than the principal forces in the cutting of WC-Co. These phenomena were different from the ordinary cutting such as cutting of steel or cast iron. (2) The cutting speed hardly influenced the thrust force, because of the frictional force between the cutting tool edge and small WC particles at low cutting speed region such as 2$\mu\textrm{m}$/s. It seemed that the thrust cutting force occurred by the contact between the flank face and work material near the cutting edge. (3) The wear mechanism for PCD tools is abrasion by hard WC particles of the work materials, which leads diamond grain to be detached from the bond. (4) From the SEM direct observation in cutting the WC-Co, it seems that WC particles are broken and come into contact with the tool edge directly. This causes tool wear, resulting in severe tool damage. (5) In the orthogonal micro cutting of WC-Co, the tool wear in the flank face was formed bigger than that in the rake face on orthogonal micro cutting. And the machining surface integrity on the side of the cutting tool with a negative rake angle was better than that with a positive one, as well as burr in the case of using the cutting tool with a negative rake angle was formed very little compared to the that with a positive one.

• Proceedings of KOSOMES biannual meeting
• /
• 2006.11a
• /
• pp.253-258
• /
• 2006

This paper aims to measure and evaluates the technical efficiency with two inputs and four outputs with the use of fuzzy DEA(Data Envelopment Analysis) in Korean RCC(Rescue Co-ordination Center)/RSC(Rescue Sub-Center). Especially, this paper included not only the marine accident data which occurred for the analysis in particular but also the possibility data of a potential marine accident by an Environmental Stress value and analyzed the technical efficiency. And in this paper, asymmetrical triangular fuzzy number is presented about inputs/ outputs data and a procedure is suggest for it solution. The basic idea is to transform the fuzzy CCR model into a crisp linear programming problem by applying an alternative ${\alpha}-cut$ approach. Also this paper propose a ranking method for fuzzy RCC/RSC using presented fuzzy DEA approach. The result, when ${\alpha}-cut$ is 0.5, efficiency priority should be in order to YS, BS, MP, TS, JJ, PH, US, IC, SC, DR, GS, TA, WD RCC/RSC. Finally, Inefficiency TA, WD RCC/RSC have to benchmarking with reference sets.