• Journal of Welding and Joining
• /
• 제3권1호
• /
• pp.40-45
• /
• 1985

Wire meling characteristics were examined with variation of gas formers such as $MgCO_3, CaCO_3 and Li_ 2CO_ 3$ by self-shielded flux cored arc welding. The flux cored wire of overlap type was welded by DCRP. The results obtainedareas follows. 1) Drop type was observed with no gas former, repelled type with MgCO_3$ added and short circuit type with $Li_2CO_3$ added. The variation of transfer mode was related to the blowing force of $CO_2$ gas and the surface tension of the slag. 2) Droplet size increased with adding gas formers due to the effect of $CO_2$ gas cushion. 3) Core spikes were observed more frequently with increasing the amount of gas formers.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1998년도 특별강연 및 추계학술발표 개요집
• /
• pp.189-192
• /
• 1998

• 한국기계기술학회지
• /
• 제13권1호
• /
• pp.17-22
• /
• 2011

As the quality of a weld joint is strongly influenced by process parameters the welding process, an intelligent algorithms that can predict the bead geometry and shape to accomplish the desired mechanical properties of the weldment should be developed. In this study, prepared by ${\Phi}1.6mm$ GMA welding of metal wire nose Advice jowelui 350A 600A grade level inverter welder and DAIHEN SCR's were carried out using welding. Welding conditions were 5.5m/min wire feed rate the welding current is rapidly transmit approximately 260A, welding voltage was about 30V. CTWD a 22mm, shielding gas was Ar 20L/min and the welding speed was a 240mm/min. Using data collected during welding equipment welding current and welding voltage waveform was analyzed by measuring the volume of the transition mode. Addition of $CaCO_3$ as a loss of the spread of the weld bead dilution rate decreased, suggesting that, GMA in the overlay welding bead shape control, dilution control and may be used as a welding flux is considered. Stabilizing effect of the arc by the Ca-containing $CaF_2$, $CaCO_3$, $CaMg(CO_3)_2$, respectively, welding flux 0.1wt.% added GMA welding and weld overlay were evaluated with dilution, $CaF_2$, and $CaMg(CO_3)_2$ added to the dilution of Seemed to increase.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.81-83
• /
• 2003

The potential advantages of the hybrid welding process are improved weld penetration, enhanced gap tolerance, control of weld metal composition, and improved weld quality in comparison to laser or arc welding. Especially, the deep penetration of hybrid welding is very attractive in welding of thick plates. In this study, therefore, the influence of arc power in hybrid welding on detailed bead dimensions at different laser power levels was investigated.

• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.69-76
• /
• 2000

Formation of the weld defect, such as a blowhole and a pit in lap-jointed fillet arc welds has been a serious problem in arc welding Zn-coated steel sheet. In this study, the relationship among welding conditions, welding materials and defect formation was investigated in order to minimize these defects in the CO₂welds. In addition, the arc stability of the commercial welding wires was evaluated for revealing their effects on defect formation. Main conclusions obtained are as follows: 1) There was no difference between shear tensile strength of the sound welds and that of the welds with blowholes whose diameters are less than 0.5mm. However, the welds with blowholes whose diameters are equal or large than 0.5mm and pits exhibited tensile strength 10∼ 20% and 30∼40% lower than that of the sound welds respectively. 2) The optimum welding condition to effectively prevent or reduce the weld defects formation are as follows: -The welding variables of 220A-23V-100cm/min and 120A-19V-30cm/min were recommended for minimizing the weld defects. -The gap between the two sheets at the lap-joint should be controlled to more than 0.2mm. -Solid wire was less susceptible to the formation of the weld defects than the flux-cored wire. -The low welding current condition produced less weld defects than the high welding current condition. 3) One of the reason why the amount of the defect was reduced at the low welding current was the gas discharging by the active agitation of the molten pool, due to an increasing in the number of the short circuit.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.581-586
• /
• 2000

Gas metal arc welding(GMAW) uses a continuously fed electrode as a filler metal. The arc is shielded from atmospheric contamination by an inert gas active or inert/active gas mixture delivered through the welding gun and cable assembly. The recent research topics on $CO_2$ are welding machines are focused mainly on the reduction method of generated spatter by using new type consumable electrode metal or inverter control method. The various current waveform control methods have been researched for welding performance improvement. Until now current waveform control methods reduce to spatter occurred by instantaneous short circuiting,. but these methods is drawback that no reduce spatter occurred by arc reignition. In this paper the previous arc reignition current control method for welding performance improvement of inverter arc welding machine is studied and compared the various current control methods with the previous arc reignition current control method.

• Journal of Welding and Joining
• /
• 제20권6호
• /
• pp.776-782
• /
• 2002

The experimental model of arc sensor in $CO_2$ arc welding has been individually developed according to welding condition and welding procedure. Therefore, the development of new arc sensor having the features of all conventional arc sensor is important in point of its application to various welding environment. In this study, the arc sensor experimental models comprised of a regression model and noise term were formulated using conventional arc sensing algorithm such as current area difference, current integration difference and weaving end current difference method, and their features were observed. The new regression arc sensor model was suggested using multiple linear regression analysis using current variables as independent variables of regression analysis. The artificial neural network model was also suggested where current variables and offset distance was used input/out variables of input/output node.

• 전력전자학회논문지
• /
• 제3권2호
• /
• pp.92-98
• /
• 1998

최근 전력용 대용량 반도체 소자의 개발과 저가형 마이크로프로세서의 발전에 따라서 일반 산업현장에서도 디지털 제어방식이 일반화 되어가고 있다. 그러나 용접산업분야에서는 이러한 마이크로프로세서를 적용한 용접기 시스템에 관한 연구가 미진하고 이에 따라서 용접기에 필요한 각종 보호 및 용접성능향상을 위한 기능을 구현하기 위한 다수의 소자를 사용하여야한다. 따라서 본 본문에서는 3상 제어 정류형 CO2 가스메탈 아크 용접기의 디지털 컨트롤러 설계와 용접기에 필요한 각종 보호 및 용접성능향상을 위한 기능이 디지털화에 관하여 연구하였고, 그 결과 용접성능 향상뿐만 아니라 기존의 아날로그 컨트롤러와 비교시 제작비 절감도 가능하였다.

• 한국산학기술학회논문지
• /
• 제15권10호
• /
• pp.5933-5938
• /
• 2014

본 연구에서는 Atos 60의 시험편에 혼합가스의 변화에 따른 FCA용접을 하였고, 용접특성 분석 위하여 용접공정상의 실시간 모니터링 시스템과 용접 후 기계적 성질을 평가 하였다. Ar 80%+$CO_2$ 20% 혼합하고 낮은 속도로 용접한 경우 가장 미려한 비드와 스패터 발생이 적게 나타났으며, 반면 $CO_2$ 100%인 경우 스패터가 많이 발생하는 것을 확인하였다. 정상단락이 발생하는 저전류 영역으로 혼합가스의 사용에 대한 스패터 발생을 확인 할수 있는 조건이며, $CO_2$ 100%인 경우 각층의 단락율은 약 2배 이상 높았고, Peak의 분포가 많은 아크의 불안정 상태로 나타났다. 인장시험결과 Ar 80%+$CO_2$ 20%, Ar 90%+$CO_2$ 10%, $CO_2$ 100%의 항복강도는 각각 511MPa, 507MPa, 469MPa 이었으며, $CO_2$ 100%의 항복강도 보다 각각 약 8.9% 8.1% 향상되었다. 인장강도는 각각 622MPa, 609MPa, 581MPa로 $CO_2$ 100%의 인장강도 보다 각각 약 7.0%, 4.8% 향상되었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 춘계학술발표대회 개요집
• /
• pp.224-227
• /
• 2002