• Journal of Welding and Joining
• /
• v.28 no.5
• /
• pp.75-79
• /
• 2010

The Remote welding system(RWS) using $CO_2$ laser equipment has focusable distance of laser beam longer than 800 mm from workpiece and can deflect the laser beam by the scanner mirrors very rapidly. In the case of normal welding system based on robot, there is a limit to move the shortest path in short time and this causes interference between robot and workpiece. On the other hand, RWS is the optimized equipment to get big merits with advanced sequence of welding and short cycle time. However, there is still a pending task such as the control of plasma in the welding process of thick sheets therefore, it requires high power laser beam because of the absence of assist gas equipment in itself. In this study, high-tensile steel plates were overlap welded with $CO_2$ RWS for the production of car body and the influence of penetration depth according to the existence of assist gas was analyzed. Excellent tensile strength with enough width of molten zone independent to penetration depth was observed under welding condition with 3.6 kW laser power and 2.8 m/min welding speed without assist gas. Finally, the proto-type automotive parts were produced by applying the deduced optimal welding condition.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.274-278
• /
• 2003

In recent, an application of high energy density beam we/ding is increasing to obtain the high quality in weldments. Laser welding, especially, has been recognized as an useful method and its beam power has also increased according to the development of relevant technology. However, welding method in the fields of power plant is conservative because their structures have required to endure high temperature and pressure. So, authors conduct the numerical simulation in order to consider the possibility of laser welding on the material of the pressure vessels ($2\frac{1}{4}Cr-1Mo$ steel). As a result of this study, we can confirm the advantages of laser welding and obtain useful information for the experiments of weldability.

• Journal of Welding and Joining
• /
• v.2 no.2
• /
• pp.22-28
• /
• 1984

$CO_2$ 용접은 50년 중반경에 실용화되어 조선물량의 증가와 더불어 발전해 왔다. 당사(대우조선)에서는 81년 CO$_{2}$ 용접기를 도입한 이래 84년 초부터 $CO_2$ 용접법의 확대 보급을 목적으로, 페인트가 용접성에 미치는 영향을 연구하였다. 유기페인트와 무기페인트 등 페인트 종류를 달리했을 때 용접결함의 발생정도, 도막 두께를 달리했을 때 결함의 원인 중 가장 크게 영향을 미치는 용접결함의 발생 정도, 기타 용접조건에 따른 용접결함의 발생정도를 실험을 통하여 연구하였다. 연구 결과에 의하여 당사에서는 무기페인트의 사용이 권장되고 있다.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.19 no.4
• /
• pp.328-334
• /
• 2009

There are various methods for welding fume control. These methods can be divided into local exhaust system, general ventilation system and integrated control system. With the general ventilation system, we should have a good prediction tool for testing various appropriate control options. But, until now there are not many studies about how to predict the welding fume concentrations. Especially, the prediction of welding fume concentration is not a very easy task because welding fume is the particulate matters. In this study, we tried to measure $CO_2$ concentrations and welding fume concentrations in a small single room with a small ventilation opening. Using commercially available CFD (Computational Fluid Dynamics) software, we tried to predict $CO_2$ concentrations under the exactly same conditions. Then, we tried to compare the numerical $CO_2concentrations$ with the experimental results to know whether we could predict $CO_2$ concentrations. Then we tried to compare $CO_2$ concentrations with experimental welding fume concentrations to know whether we can use the numerical $CO_2concentrations$ to predict the welding fume concentration indirectly.

• Laser Solutions
• /
• v.5 no.1
• /
• pp.13-21
• /
• 2002

Compared to conventional welding process, laser welding does not use additional filler wire generally. However, if laser welding uses the filler wire, the applicability of the method can be broaden. When laser welding uses the filler wire, it is possible to enhance gap bridging ability and to prevent cracking in weld pool by metallurgical control. In this study, we had optimal condition and experimented gap bridging capability for butt welding with 2㎜ Al5052 alloys using the filler wire feeder. As the experimental parameters, wire feed rate and wire diameter are considered and then the performance of wire feed is evaluated under various filler wire welding conditions.

• Journal of Welding and Joining
• /
• v.16 no.4
• /
• pp.63-72
• /
• 1998

In this study, the effects of the current pulsing conditions, on the spatter generation rate during the $CO_2$ gas metal arc welding (GMAW) were investigated. Normally using the inverter type power supply, of which the welding current waveform was regulated to reduce the spatter generation rate, but in this study pulsing was imposed on the welding current. Observation of the metal transfer phenomena during the pulsed current GMAS indicated that the droplet transfer from the electrode via the short circuit transfer and the repelling transfer mode could be minimized by selecting optimum combinations of pulsing parameters, which include base and peak current, base and pak duration. It was also demonstrated in this study that proper combinations of the pulsing parameters led to reduce generation of spatters during GMAW shielded by $CO_2$ gas.

• Proceedings of the KIEE Conference
• /
• 2005.10a
• /
• pp.191-196
• /
• 2005

In this paper, a multi-functional control module is developed to improve the confidence of CO2 welding. In the developed system, a main controller of an automatic welding system including of I/O port is modulated by microprocessor. The developed multi-functional control module is familiarized to the conventional automatic welding system. Therefore, the confidence of CO2 welding is improved when the main controller of an automatic welding system is broken down.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.170-170
• /
• 2000

• Journal of Welding and Joining
• /
• v.24 no.4
• /
• pp.27-31
• /
• 2006

Optimization of process parameters for laser-arc hybrid welding process is intrinsically sophisticated because the process has three kinds of parameters-arc, laser and hybrid welding parameters. In this paper, the relationship between weldability and several process parameters such as laser beam-arc distance, electrode height, welding current and welding speed, were investigated by the full factorial experimental design. Weld quality was evaluated by using weight of spatters which is related with the pore area. It was found that the weld quality was increased with the increases in laser beam-arc distance and welding current, and decreased with the increases in electrode height and welding speed.

• Laser Solutions
• /
• v.5 no.1
• /
• pp.33-42
• /
• 2002

In order to investigate the characteristics of the plasma induced by lap-joint CO$_2$ laser welding of automotive steel sheets, the effects of welding speed, shield gas flow rate, gap size, and laser beam defocus to plasma intensity emitted from keyhole have been investigated. The plasma light is measured by fiber and photodiode. Also, the plasma images were captured by the high speed digital camera in 1000frames/sec in order to correlate the plasma light signal with plasma pattern. From the results, it is observed that the difference of the plasma intensity for between the deep penetration and partial penetration exists from 1.2 to 2 times. The plasma light intensity decreased in case of the deep penetration Is observed due to the exhausting of the plasma gas under the sheet. On the other hand, under the conditions of the deep penetration, the plasma intensity is significantly increased by controling the conditions decreasing the penetration depth. It was specially founded that the effect of 0.3mm gap size at partial penetration condition is approximately similar to deep penetration in 0mm gap. It is concluded that the plasma intensity is able to evaluate the penetration depth in lap-joint welding and appears to offer the most straightforward correlation to the welding process.