• 한국표면공학회지
• /
• 제53권1호
• /
• pp.1-8
• /
• 2020

Sulfamate-chloride baths were fabricated to study the properties of the electrodeposited Ni and NiCo thin films. The dependences of current efficiency, deposit composition of Ni and Co, residual stress, surface morphology and microstructure of electrodeposited Ni and NiCo thin films on CoCl₂ concentration in sulfamate-chloride baths were investigated. The current efficiency was measured to be more than about 90%, independent of the changes of CoCl₂ concentration in the baths. Residual stress of Ni and NiCo thin films was increased from about 45 to about 250 MPa with varying CoCl₂ concentration from 0 to 0.210 M CoCl₂ in the baths and then reached to a plateau, about 250 MPa above 0.420 M CoCl₂ concentration. Nodular surface morphologies were observed at most CoCl₂ concentrations in the baths except 0.210 M. NiCo thin film electrodeposited from the bath with 0.210 M CoCl₂ concentration showed an acicular surface morphology. Pure Ni thin film consists of FCC(111), FCC(200), FCC(220), and FCC(311) peaks without any preferred orientation. On the other hand NiCo thin films make up of HCP(100), FCC(111), HCP(101), FCC(200), FCC(220) or HCP(110), FCC(311) or HCP(112) and FCC(222) peaks. It was revealed from the analysis of XRD result that FCC(111) peak at the NiCo thin film electrodeposited from the bath with 0.084 M CoCl₂ concentration can be regarded as the preferred orientation. However the peak of the preferred orientation was changed to FCC(220) or HCP(110) above 0.084 M CoCl₂ concentration in the baths. Then the intensity of FCC(220) or HCP(110) peak was gradually decreased with increasing CoCl₂ concentration further. The crystalline size of pure Ni thin film was observed to be about 53 ㎛ and those of NiCo thin films were in the range of 35~45 ㎛.

• 생물환경조절학회지
• /
• 제2권1호
• /
• pp.27-36
• /
• 1993

Carbon dioxide enrichment for greenhouse crops has generally been a standard commercial practice for many years. Vegetable crops such as tomato, cucumber, and lettuce respond positively to the $CO_2$ enrichment. But improper $CO_2$ enrichment leads to physiological damage and economical loss. This study was carried out to develop a $CO_2$ concentration control algorithm considering growth stage and efficiency. The measurand was $CO_2$ consumption rate and top fresh weight that represents growth stage. The weight of top fresh lettuce as a whole in the tray was measured through a non-destructive method. The demand in $CO_2$ concentration according to growth stage was investigated. The results are summarized as follows. 1. The $CO_2$ consumption rate could be measured within the error of $\pm$ 15.4mg$CO_2$/hr in the range of $CO_2$ concentration of 500-1500ppm. 2. The weight of top fresh lettuce could be measured within the error $\pm$ 4.3g in the range of 0-1400g. 3. The $CO_2$ control model developed could determine an economical $CO_2$ supply rate considering $CO_2$ consumption rate and leakage rate. 4. The $CO_2$ control algorithm based on the control model was composed of feedforward control for maintaining a stable $CO_2$ concentration level, and feedback control with $CO_2$ consumption rate and top fresh weight for adapting to the change in $CO_2$ demand by growth stage. 5. For the performance test with the developed control algorithm on lettuce the decrease in $CO_2$ supply rate was obtained without a significant decrease in top fresh weight.

• 한국분말재료학회지
• /
• 제21권2호
• /
• pp.108-113
• /
• 2014

Flake-like $LiCoO_2$ nanopowders were fabricated using electrospinning. To investigate their formation mechanism, field-emssion scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy were carried out. Among various parameters of electrospinning, we controlled the molar concentration of the precursor and the PVP polymer. When the molar concentration of lithium and cobalt was 0.45 M, the morphology of $LiCoO_2$ nanopowders was irregular and round. For 1.27 M molar concentration, the $LiCoO_2$ nanopowders formed with flake-like morphology. For the PVP polymer, the molar concentration was set to 0.011 mM, 0.026 mM, and 0.043 mM. Irregular $LiCoO_2$ nanopowders were formed at low concentration (0.011 mM), while flake-like $LiCoO_2$ were formed at high concentration (0.026 mM and 0.043 mM). Thus, optimized molar concentration of the precursor and the PVP polymer may be related to the successful formation of flake-like $LiCoO_2$ nanopowders. As a results, the synthesized $LiCoO_2$ nanopowder can be used as the electrode material of Li-ion batteries.

• 한국포장학회지
• /
• 제17권2호
• /
• pp.33-37
• /
• 2011

변패성 식품의 하나로서 양념돼지불고기의 미생물적 저장수명을 실시간적으로 제어하는 방법으로서 포장 내 $CO_2$ 농도의 측정을 이용하는 방법을 고안하고 동적온도조건에서 그 적용가능성을 확인하였다. 식품으로부터의 $CO_2$ 생산 속도 혹은 포장 내 $CO_2$ 농도변화가 증가하기 시작하는 시점이 미생물적 한계품질에 해당되었고, 이를 저장수명의 결정의 지표로 사용할 수 있는 것으로 나타났다. 이는 또 특정 $CO_2$ 농도에 도달되는 시점, 즉 $CO_2$ 농도변화의 유도기와도 일치하였다. 제안된 logic은 $CO_2$ 농도를 실시간으로 측정하고 무선으로 데이터를 전송할 수 있는 sensor 시스템에 의하여 가능성이 확인되었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.54-59
• /
• 2007

In a view of capturing $CO_2$ as a greenhouse gas, an experimental study was conducted on the combustion characteristics of pulverized coal in $O_2$/$CO_2$ environment using TGA/DSC and DTF facilities. The effects of gas composition and concentration on the processes of devolatilization and char burning experienced by coal particles in combustion furnace and on the concentration of products such as $CO_2$, CO and $NO_x$ were observed using TGA/DSC and DTF respectively. As results, it were found that the rate of devolitilation is nearly independent on the $O_2$ concentration if it is over 20% but the char burning rate is a sensitive function of $O_2$ percent, and the two rates can be controlled by $O_2$ concentration in order to be similar with those of air combustion case. It was also found that high concentration $CO_2$ can be captured by oxy-coal combustion and high concentration of CO and low value of $NO_x$ are exhausted in that case. Additionally, NO reducing reaction by CO with char as catalyst was observed and a meaningful results were obtained.

• Journal of Mechanical Science and Technology
• /
• 제19권11호
• /
• pp.2068-2076
• /
• 2005

The influence of oxygen concentration and CO$_{2}$ as diluent in oxidizer side on soot characteristics was studied by Laser Induced Incandescence, Time Resolved LII and Transmission Electron Microscopy photography in non-premixed co flowing flames. Through the comparison of TEM photographs and the decay rate of LII signal, suitable two delay times of TIRE-LII method and signal sensitivity ($\Delta$S$_{TIRE-LII/) were determined. The effects of O$_{2}$ and CO$_{2}$ as diluent in oxidizer side on soot formation are investigated with these calibrated techniques. The O$_{2}$+CO$_{2}$, N$_{2}$, and [Ar+CO$_{2}$] mixture in co-flow were used to isolate CO2 effects systematically. The number concentration of primary particle and soot volume fraction abruptly decrease by the addition of CO$_{2}$ to the co-flow. This suppression is resulted from the short residence time in inception region because of the late nucleation and the decrease of surface growth distance by the low flame temperature due to the higher thermal capacity and the chemical change of CO$_{2}$ including thermal dissociation. As the oxygen concentration increases, the number concentration of soot particles at the inception region increases and thus this increase of nucleation enhances the growth of soot particle.

• 설비공학논문집
• /
• 제19권10호
• /
• pp.718-725
• /
• 2007

In the general vapor-compression refrigeration system, refrigeration lubricant circulates in refrigeration system with refrigerant. Knowledge of the amount of circulating lubricant is very important to exactly calculate capacity of the refrigeration system. An experimental study was conducted to estimate the oil concentration of a flowing $CO_2/Oil$ mixtures. POE and PAG oil are considered as test lubricants in this study. Performance tests were conducted under simulated liquid conditions for $CO_2/POE$ oil mixture in oil concentration of 0 to 10 weight-percent and $CO_2/PAG$ oil mixture in oil concentration of 0 to 6 weight-percent in the temperature ranges of $-5^{\circ}C\;to\;15^{\circ}C$. The results obtained indicate specific gravity of $CO_2/Oil$ mixture is increased as oil concentration is increased and as temperature of mixture is decreased. Oil concentration correlation of $CO_2/POE$ oil mixture and $CO_2/PAG$ oil mixture is suggested, based on the measurement of specific gravity and temperature. This correlation enable to predict the oil concentration without extraction of the mixture and can be applied for $CO_2/POE$ mixtures and $CO_2/PAG$ mixtures.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.77-84
• /
• 2001

Measurements of local CO, $CO_2$, $O_2$, $N_2$, $C_3$H$_{8}$, NOx concentrations and flame temperature are made for partially premixed flame with and without acoustic excitation. The CO, $CO_2$, $O_2$, $N_2$, and $C$_3$H_8$ concentrations are determined by thermal conductivity detection (Gas-chromatograph) and NOx concentrations are determined by chemiluminescent detection (NOx analyser). To measure local sample concentration, sampling probe was made by quartz with inlet diameter of 0.25mm. In the case of excitation, the visual shape of the flame is changed from laminar flame to turbulent-like flame. The flame length is also reduced, and the flame width becomes broad. In the observation of emission concentration without acoustic excitation, meanwhile, the $CO_2$ and NOx concentrations peak at flame front where the mixture meets with surrounding air, and the CO concentration is increasing at maximum position of CO2 concentration and peaks at the centerline of the burner. In the case of acoustic excitation, the $CO_2$ concentration is widely occurred at nozzle of the burner and is higher relative to unexcitation. The CO concentration is much reduced, but NOx concentration is more increasing. And flame temperature is higher relative to unexcitation. These are caused by enhancing of mixing with surrounding air due to excitation. However, in the case of acoustic excitation, the total NOx concentration is reduced because of the shortened flame length which affects residence time.e.

• 한국화재소방학회논문지
• /
• 제26권6호
• /
• pp.15-23
• /
• 2012

$CO_2$ 소화설비의 소화성능 시험방법에는 직접시험방법이 가장 좋지만, 고비용과 환경문제 그리고 시험절차의 어려움으로 간접시험방법을 사용하는 경우가 많다. 그러나 석유화학플랜트나 원자력발전소와 같은 국가 중요위험시설은 화재가 발생하면 대형피해가 발생할 수 있으므로 직접방사시험을 통해 소화성능을 검증할 필요가 있다. 본 연구는 국가 중요위험시설에 설치된 전역방출방식의 $CO_2$ 소화설비 중에서 표면화재 방호구역과 심부화재 방호구역을 각각 선정하여 $CO_2$ 소화설비의 소화성능을 검증해 보았다. 소화성능은 방호구역 내에 방사된 $CO_2$의 농도가 설계농도기준(NFSC 및 NFPA)에 만족해야 그 성능을 인정받을 수 있다. 여기서, 설계농도는 $CO_2$ 소화약제가 화염을 제어할 수 있는 소화농도에 여유율 20 %를 감안한 농도를 의미한다. 시험결과 표면화재와 심부화재 방호구역 모두 $CO_2$ 설계농도를 확보하고 있음을 확인하였고 심부화재의 경우에는 20분 이상 설계농도가 유지되었다. 본 연구를 통해 국가 중요위험시설에 대한 직접방사시험 방법 및 판정방법을 소개하였고 향후 이와 같은 국가 중요위험시설에는 직접방사시험을 통해 소화설비의 신뢰성을 검증해야 할 필요성을 제기하였다.

• 한국환경농학회지
• /
• 제42권3호
• /
• pp.231-238
• /
• 2023

We analyzed the variations in the CO₂ concentration and temperature between a CO₂-enriched and control greenhouse. We cultivated Alstroemeria 'Hanhera' in the two greenhouses and assessed the growth parameters (stem length, stem thickness, and the number of flowers) and yield. The CO₂-enriched greenhouse had a CO₂ generator that produced CO₂ at rate of 0.36 kg/h and its windows were programmed to open when the temperature exceeded 20℃ and close when it dropped below 15℃. The control greenhouse had no additional CO₂ supplementation, and its windows were programmed to open when the temperature exceeded 20℃ and close at approximately 17:00. In the morning, CO₂ concentration remained above 500 ppm in the CO₂-enriched greenhouse, which was higher than that in the control greenhouse (approximately 370 ppm). The ventilation effect only through the side windows to reduce the temperature in both greenhouses did not appear dynamically. CO₂ supplementation promoted plant growth, resulting in a significant increase in plant yield of over 60% compared to that of the control greenhouse. Our findings suggest that elevated CO₂ concentration in the morning can significantly promote the growth and development of Alstroemeria during the winter.