• Journal of Soil and Groundwater Environment
• /
• v.13 no.1
• /
• pp.24-31
• /
• 2008

Sulfate reducing bacteria (SRB) is universally distributed in the sediment, especially in marine environment. SRB reduce sulfate as electron acceptor to hydrogen sulfide in anaerobic condition. Hydrogen sulfide is reducing agent enhancing the reduction of the organic and inorganic compounds. With SRB, therefore, the degradability of organic contaminants is expected to be enhanced. Ferrous iron reduced from the ferric iron which is mainly present in sediment also renders chlorinated organic compounds to be reduced state. The objectives of this study are: 1) to investigate the reduction of TCE by hydrogen sulfide generated by tht growth of SRB, 2) to estimate the reduction of TCE by ferrous iron generated due to oxidation of hydrogen sulfide, and 3) to illuminate the interaction between SRB and ferrous iron. Mixed bacteria was cultivated from the sludge of the sewage treatment plant. Increasing hydrogen sulfide and decreasing sulfate confirmed the existence of SRB in mixed culture. Although hydrogen sulfide lonely could reduce TCE, the concentration of hydrogen sulfide produced by SRB was not sufficient to reduce TCE directly. With hematite as ferric iron, hydrogen sulfide produced by SRB was consumed to reduce ferric ion to ferrous ion and ferrous iron produced by hydrogen sulfide oxidation decreased the concentration of TCE. Tests with seawater confirmed that the activity of SRB was dependent on the carbon source concentration.

• Journal of Animal Environmental Science
• /
• v.14 no.2
• /
• pp.75-80
• /
• 2008

High concentration of $NH_3$, $CO_2$, and lots of dust are found in modern densely raising stall system, as results, they provide a negative influence on animal and lamer health, and production ability. Therefore, it is necessary to keep clean the inside of stall air to increase the productivity. A wet type air cleaner has been developed to clean the stall air. The work principle is that the inside air are sucked through the fan, and the rotating discs make a water into a fineness spray and blows into the stall. The spray can take the dust, $NH_3$, and odor from the stall inside air and give back to the circulating water, which can be refreshed in 2 hours interval. In the Present study, we measured the $NH_3$, dust, odor, temperature and humidity in a swine stall that were installed two wet air cleaners with 700 fattening swine with on-mode and off-mode of wet air cleaners. In fall, the concentrations of $NH_3$ in off-mode stall were maximum 24 ppm and minimum 16 prm, and the average was 18.2 ppm. However in on-mode stall the $NH_3$ concentrations were maximum 7ppm and minimum 1ppm, and the average was 2.7ppm. The concentration of $NH_3$ in on-mode was 74% lower than off-mode stall. Odor was measured by olfactometer. In the off-mode stall, the odor unit was 3,800 OU/$m^3$, but in the on-mode stall the odor unit was 2,100 OU/$m^3$ Odor removal efficiency was about 45% in on-mode stall. The dust measure was divided into 3 categories, $PM_{10}$, $PM_{2.5}$ and $PM_{1.0}$. Whereas the $PM_{10}$ showed no significant differences between the tests, $PM_{2.5}$ and $PM_{1.0}$ in the fine particle range reduced remarkably in the on-mode.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.581-585
• /
• 1999

The surface treated hydroxypropyl methylcellulose(HPMC) which could adjust the soluble time was synthesized when 40 wt % glyoxal solution and $KH_2PO_4$ were sprayed and reacted. And also, the solution dynamic at different ratios of two adding agents were identified If the surface of HPMC was treated with only glyoxal, the dispersion characteristics at different ratios of two adding agents were identified If the surface of HPMC was treated with only glyoxal, the dispersion was observed in the neutral solution and the viscosity was increased after directly dissolved as the solution become alkali condition. But the fine-powder type of HPMC which reacted with glyoxal and $KH_2PO_4$ was dispersed regardless of pH of solution and observed that it was dissolved and its viscosity increased after elapsing some time. With increasing amount of glyoxal and $KH_2PO_4$, the soluble time was delayed. The reaction condition was about 60 min at $75{\sim}85^{\circ}C$. Especially, the removal process of organic solvent after reaction was not required due to reaction under water solution without organic during glyoxal and $KH_2PO_4$ treatment. And also, the HPMC which could adjust the soluble rate in water or organic solvent by changing the degree of substitution of HPMC was synthesized.

• Journal of Embryo Transfer
• /
• v.13 no.1
• /
• pp.11-19
• /
• 1998

This study was to determine the effect of ionomycin and 6-dimethylaminopurine (6-DMAP) and/or elcetrical stimulation on the oocyte activation and production of rabbit nuclear transplant embryos. The oocytes were collected from the oviduct of superovulated rabbits at 14 h post hCG injection and cultured in TCM-199 containing 10% FBS until 19 h post hCG injection. To determine the optimum concentration and exposure time of 6-DMAP, some oocytes were activated with 5 $\mu$M ionomycin for 5 min and then in 2.0 mM 6-DMAP for 0.5 to 3.0 h, or in 1.0 to 3.0 mM 6-DMAP for 2.0 h. Other control oocytes were stimulated electrically(3X, 1.25 kV/cm, 60 $\mu$sec) in 0.3 M mannitol solution supplemented with 100 $\mu$M CaCl$_2$ and MgCl$_2$. The nuclear donor embryos of 8-cell stage were synchronized to G$_1$ phase of 16-cell stage, and the recipient cytoplasms were obtained from removal of the first polar body and a portion of membrane bound cytoplasm of the oocytes collected at 15 h post hCG injection. A separated blastomere was injected into the perivitelline space of the enucleated oocytes. The oocytes injected with nucleus were cultured until 19 h post hCG and then electrofused and activated by electrical stimulation with or without ionomycin and 6-DMAP. These nuclear transplant embryos were cultured in TCM-199 containing 10% FBS in 39˚C, 5% CO2 incubator for 120 h. For the oncytes activated parthenogenetically with electrical stimulation with or with-out ionomycin and the various concentration of exposure time of 6-DMAP, the highest cleavage(92.3%) and development to blastocyst stage(41.0%) were resulted from the oocytes activated by ionomycin and 2.0 mM 6-DMAP for 2.0 h, which were found to be significantly(P<0.05) higher than the cleavage(45.2%) and developement to blastocyst stage(14.3%) from the oocytes activated with electrical stimulation. The significantly(P<0.05) more oocytes(71.4%) developed to 4 cell stage at 24 h post activation by ionomycin and 6-DMAP than those by electrical stimulation(18.9%). For the nuclear transplant embryos, the cleavage rate was similarly high in oocyte activation by electrical stimulation with(79.4%) or without ionomycin and 6-DMAP(70.5%). However, the embryo development to blastocyst stage was significantly(P<0.05) higher in oocyte activation by electrical stimulation with ionomycin and 6-DMAP(44.4%) than by electrical stimulation only(25.0%). The significantly(P<0.05) more nuclear transplant embryos(45.6%) developed to 4 cell stage at 18 h post activation by electrical stimulation with ionomycin and 6-DMAP than those by electrical stimulation only(10.6%). These results indicated that the supplemental oocyte activation by ionomycin and 6-DMAP with electrical stimulation enhanced and accelerated the preimplanted in vitro development of the rabbit nuclear transplant embryos.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.3
• /
• pp.89-96
• /
• 2000

Waste oyster shell was used to study the applicability on anaerobic composting of garbage. Experiment was conducted with five anaerobic reactors. After garbage and compost for inoculation were mixed, waste oyster shell was added into mixed waste in mesophillic temperature for 60 days with 30%, 60% respectively. The amount of produced methane gas, gas composition, organic removal efficiency and pH were measured. Result showed that the amounts of produced gas were 0.62 l /g-VS in R-1, 0.63 l /g-VS in R-2, 0.16 l /g-VS in R-3, 0.75 l /g-VS in R-4, 0.21 l /g-VS in R-5 and the amounts of produced methane gas were 0.32 l /g-VS in R-1, 0.37 l /g-VS in R-2, 0.04 l /g-VS in R-3, 0.42 l /g-VS in R-4, 0.05 l /g-VS in R-5. Proportion of mathane gas which determines the efficiency of anaerobic composting was over 55%. pH were 6.0~8.0 in R-2 and R-4 which contained 30% of waste oyster shell and pH were increased over 8.5 in R-3 and R-5 which contained 60% of waste oyster shell. Since pH were so high and it had a negative effect on microbial growth, anaerobic reaction were not well operated in R-3 and R-5.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.769-777
• /
• 2002

Using four components - nonionic surfactants, water, hydrocarbon oil and an alcohol as cosurfactant, 12 types of cleaning agents were prepared, and their physical properties such as surface tension, viscosity, electroconductivity and phase stability were measured. As the formulated cleaning agents have low surface tensions(30.5-31.1 dyne/cm) and low viscosities (1.6-7.2 c.p.), they are satisfied with the general physical properties of water-in-oil(W/O) microemulsions for their industrial use. They showed a tendency that their temperature range for stable one-phase microemulsion decreased in accordance with the increase of alcohol/surfactant(A/S) ratio in the formulations. However, the temperature range of one-phase microemulsion was much more affected by hydrophilic lipophillic balance(HLB) value of the nonionic surfactant which increased its temperature range and it increased in accordance with the higher HLB value in the formulations. And the maximum content of water which can keep stable one-phase W/O microemulsion was measured at each sample. In addition, their temperature range for stable one-phase microemulsion was also measured. It was confirmed that the selection of surfactant type was very important for formulating a cleaning agent, since the W/O microemulsion system with the nonionic surfactant of the lower HLB value showed better cleaning efficacy that of the higher HLB value for abietic acid as a soil, which was used for preparing a rosin-type flux. In the formulated cleaning agents with the increase of A/S ratio in the formulations, however, there was no significant difference in cleaning efficacy. It was investigated that the differences of their cleaning efficacy was affected by the change of the condition of temperature and sonicating frequency as important factors in the industrial cleaning. That is, the higher, their cleaning temperature and the lower, their sonicating frequency, the more increased, their cleaning efficacy. Furthermore, using optical instruments like UV/Visable Spectrophotometer and FT-IR Spectrometer, their cleaning efficacy for abietic acid was measured. The removal of soil from the contaminated rinse water was measured by gravity separation method in the rinse bath. As a result, the cleaning agent system having the nonionic surfactant of HLB value 6.4 showed over 85% water-oil separation efficacy at over $25^{\circ}C$. Therefore, it was demonstrated in this work that the formulating cleaning agents were very effective for cleaning and economical in the possible introduction of water recycling system.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.21-25
• /
• 2016

When copper alloy is used in etching process for the production of lead frame, the high concentration of heavy metals, such as iron, nickel and zinc may be included in the etching waste. Those etching waste is classified as a specified one. Therefore a customized design was designed for the purification process of the lead frame etching waste liquid containing high concentrations of heavy metals for the production of an electroplating copper(II) oxide. Since the lead frame etching waste solution contains highly concentrated heavy metal species, an ion exchange method is difficult to remove all heavy metals. In this study, a copper(I) chloride was manufactured by using water solubility difference related to the reduction-oxidation method followed by the reunion of copper(II) chloride using sodium sulfate as an oxidant. The hydrazine was chosen as a reducing agent. The optimum added amount was 1.4 mol per 1.0 mol of copper. In the case of removal of heavy metals by using the combination of reduction-oxidation and ion exchange resin methods, 4.3 ppm of $Fe^{3+}$, 2.4 ppm of $Ni^{2+}$ and 0.78 ppm of $Zn^{2+}$ can be reused as raw materials for electroplating copper(II) oxide when repeated three times.

• Journal of Food Hygiene and Safety
• /
• v.18 no.4
• /
• pp.189-194
• /
• 2003

Approved chemical preservatives have been widely used to preserve foods and increase their shelf life. There are increasing demends of the partial or complete removal of chemical preservatives from foods vecause of adverse health effect of chemicals. In this study, the possibility of natural antimicrobial compounds, Korean propolis as food preservatives are investigated. Propolis samples were extracted on various concentration of ethanol. Propolis extracts extracted with 100% ethanol showed the highest inhibitory effect aginst food spoilage microorganisms. The 100% ethanol extracts of propolis were selected and the antimicrobial activites of 100% ethanol extracts of proplis against several food spoilage microorganisms were examined. Bacillus subtilis, Micrococcus luteus, Escherichia coli, Staphylcoccus aureus, Bacillus cereus, Shigella sonnei, Salmonella choleraesuis, Erwinia rhapontici, and Vibrio parahaemolyticus as food poisoning microorganisms were chosen for the examination. The Propolis extracts had antimicrobial activity against food spoilage microorganisms. When the microorganisms were treated with propolis extracts, the population of food spolige microorganisms were decreased by 1~9 log.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3246-3252
• /
• 2009

The interest on the recovery of thermal energy using the waste has been rising to solve the problems of continuous increase of waste generation and the depletion of the fossil fuel recently. The incineration has been used most popularly as a treatment process of the waste for the energy recovery. However, it is expected that incineration and design cost will increase in the treatment of air contaminant emitted from incinerator. This research has simulated the actual incinerator and the flue gas treatment system using the Aspen plus which is the software to simulate the chemical process. The incineration process is composed of the 1st and 2nd combustor to burn the waste, SNCR process to reduce the $NO_x$ using the urea, and the steam generation process to save the energy during incineration. The $Ca(OH)_2$ slurry was used as an acid gas (HCl, $SO_2$) treatment materials and the removal efficiency for the products from the neutralization of acid gas in SDA and combustion ash was simulated at the bag filter. The simulation result has been corresponded with the treatment efficiency of emitted gas from the actual industrial waste incinerator and it is presumed to be used to forecast the efficiencies of flue gas treatment system in the future.

• The Journal of the Korean dental association
• /
• v.53 no.1
• /
• pp.36-46
• /
• 2015

Objectives: The objective of this work was to investigate the hospital nursing care of oral and maxillofacial health in jeju province. Methods: 438 Registered nurses(RN) who were working at each of secondary hospitals in Jeju province had responded to the questionnaire. The data were analyzed via frequency analyses and one-way ANOVA to assess the state of RN on hospital nursing care of oral and maxillofacial health. Results: The class of education on density in formal density that marked '0 hour' and '1-3 hours' were 73.5% and 19.9%, respectively. The class of refresher training on density that marked '0 hours' and '1-3 hours' were 92.9% and 6.6%, aggregately 99.5%. The nursing education on appearance after tumor of maxillofacial area that marked 'formal education' and 'none' were 45.2% and 52.1%, respectively. The score of question 'function, effect and side effect of hexamedin gaggle' was $2.68{\pm}0.95$ by Likert 5-point scale. Likewise, the scores were $2.82{\pm}0.88$ on question 'management of removal denture', $2.83{\pm}0.95$ on question 'preventive dental treatment before anticancer therapy', $2.88{\pm}0.86$ on question 'function of saliva', $2.96{\pm}0.99$ on question 'oral management of tube feeding patient', $3.13{\pm}1.00$ on question 'bacterial endocarditis from oral microflora', $3.36{\pm}0.89$ on question 'dysphagia' and $3.62{\pm}1.03$ on question 'aspiration pneumonia'. RN replied that 'lack of knowledge' and 'delay of cooperation' formed 53.7% and 33.3% respectively, on question 'problem in dental consultation other diseased patient'. Conclusions: From this study, it is necessary for RN and student of nursing science to be educated on the oral and maxillofacial nursing. Authors suggest further co-study and nation-wide research.