• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.532-536
• /
• 2005

Thermal shock resistance of structural ceramics is a property that is difficult to quantity, and as such is usually expressed in terms of a number of empirical resistance parameters. These are dependant on the conditions imposed, but one method that can be used is the examination of density, Young's modulus and thermal expansion retention after quenching. For high temperature applications, long-annealing thermal durability, cycle thermal stability and residual mechanical properties are very important if these materials are to be used between $1000^{\circ}C$ and $1300^{\circ}C$. In this study, an excellent thermal shock-resistant material based on $Al_2TiO_5-mullite$ composites of various compositions was fabricated by sintering reaction from the individual oxides and adjusting the composition of $Al_2O_3TiO_2/SiO_2$ ratios. The characterization of the damage induced by thermal shock was done by measuring the evolution of the Young's modulus using ultrasonic analysis, density and thermal expansion coefficients.

• Journal of the Korean Ceramic Society
• /
• v.43 no.4 s.287
• /
• pp.235-241
• /
• 2006

Mullite short fibers have been fabricated by adapting the Kneading-Drying-Calcination (KDC) process and characterized. The effect of the addition of foaming agent and calcination temperature on the formation of mullite fibers from coal fly ash, was examined. In the present work, ammonium alum $NH_4Al(SO_4)_2\;12H_2O$ synthesized trom coal fly ash and sodium phosphate $Na_2HPO_4\;2H_2O$ were used as foaming agents. After calcination at $1300^{\circ}C$ for 10 h and then etching with 20% HF solution at $50^{\circ}C$ for 5 h using a microwave heating source, the alumina-deficient $(AI_2O_3/SiO_2$ = 1.13, molar ratio) orthorhombic mullite fibers with a width of ${\sim}0.8mm$ (aspect ratio >30), were prepared from the coal fly ash with $AI_2O_3/SiO_2$ = 0.32, molar ratio by the addition of $NH_4AI(SO_4)_2\;12H_2O$, and with further addition of 2 wt% sodium phosphate. The excessive addition of sodium phosphate rather decreased the formation of mullite fibers, possibly due to the large amount of liquid phase prior to mullitization reaction.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.233-240
• /
• 2000

In order to fabricate dense cordierite ceramics without sintering aid, thermal behavior of Mg-Al-Si compounds during sintering was investigated. The dispersibility of cordierite suspension in aqueous media was measured by ESA(electrokinetic sonic amplitude). To prevent aggregation and insufficient dispersion of the cordierite sol, the pH of the suspension was controlled to 1.03 and 8.30 by adding $2N\;HNO_3$ and $2N\;NH_4OH$, respectively. Magnesium-aluminum-silicate complex gel coexisted in the specimen which has been gelled at $150^{\circ}C$ fir 12 hours, however several metastable phase such as ${\mu}-cordierite(Mg_2Al_4Si_5O_{18}),\;spine(MgAl_2O_4)\;and\;mullite(Al_6Si_2O_{13})$ existed below $1300^{\circ}C$ Nucleation rates of the two suspension were similar, but densification of the gel was sensitive to the pH of the sol. Densification of the sol with the pH of 8.3 was more pronounced than that of the sol with pH of 1.63.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.5
• /
• pp.301-306
• /
• 2011

In this study, zeolite was synthesized by hydrothermal, fusion, and fusion/hydrothermal methods with fly ash, coal fly ash, and a waste catalyst discharged from thermal power plants and incinerator in Ulsan area. Coal fly ashes (CFAs) and a waste catalyst containing amounts of $SiO_2$ and $Al_2O_3$ ranging from 60.29 to 89.62 wt%. CFAs were mainly composed of quartz and mullite which were assayed by a XRD pattern. Zeolite could be synthesized by CFAs and the waste catalyst when all methods were used. Na-A zeolite (Z-C1, Z-C2, and Z-W5) are mainly synthesized by the fusion method from CFAs and the waste catalyst. Z-C1 and Z-C2 formed by-products, calcite peaks, which is caused by the content of CaO in CFAs and the addition of $Na_2CO_3$ for a synthetic process.

• Journal of the Korean Ceramic Society
• /
• v.26 no.3
• /
• pp.341-346
• /
• 1989

In order to evaluate the oxidation behavior of $\beta$-Sialon, $\beta$-Sialon ceramics was prepared from Si3N4, Al2O3, AlN and Y2O3 system. The specimens were oxidized in an oxygen atmosphere at 1, 20$0^{\circ}C$ for 9days. Oxidation behavior was evaluated by weight gain oxidation process, surface roughness. Microscopy, EDX and X-ray diffraction analysis were also used for the evaluation. The weight and surface roughness ofoxidized specimens were increased with increasing the oxidation time. Oxidized products were mullite, $\alpha$-cristobalite, yttrium aluminum oxide and yttrium silicate oxide.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.68-74
• /
• 2005

The electrical arc furnace (EAF) classified as a special waste contains many flux components producing melts during a sintering process, so it decreases the sintering temperature and improves the mechanical properties of specimens. Increasing dust content in a clay-dust system brick, however, may cause the fraction defective higher due to the excessive liquid produced. To control the liquid behavior produced during sintering process for the clay-dust system specimens, the $Al_2O_3$ was added and the physical properties were analyzed. The microstructure for the clay-dust system body sintered with $Al_2O_3$ became homogeneous and the overall size of pores decreased. Adding $Al_2O_3$ to clay-dust system body increased the mechanical properties and the temperature of maximum strength increased as much as $50^{\circ}C$, and the apparent density increased and the absorption decreased. The mullite ($3Al_2O_3{\cdot}2SiO_2$) was produced during sintering process by reaction of $Al_2O_3$ and $SiO_2$ which could participate to liquid-producing-process and the viscosity of melts increased which was proved by measuring a critical viscosity temperature (Tcv) therefore, the refractoriness of specimens were improved to lower the fraction defective.

• Journal of the Korean Ceramic Society
• /
• v.46 no.3
• /
• pp.323-329
• /
• 2009

Influences of ceramic filler types and dose on the sintering, phase evolution, and dielectric properties of ceramic/CaO-$Al_2O_3-SiO_2$ glass composites were investigated. All of the specimens were sintered at $900^{\circ}C$ for 2 h, which conditions are required by the lowtemperature co-firing ceramic (LTCC) technology. Ceramic fillers of $Al_2O_3,\;SiO_2$, kaolin, and wollastonite were used. The addition of $Al_2O_3$ filler yielded the crystalline phases of alumina and wollastonite, and the densification over 95% of the relative density was achieved up to 50 wt% addition of the filler. For the cases of the fillers of $SiO_2$, kaolin, and wollastonite, crystalline phases of quartz, mullite, and wollastonite formed, while the densification decreased monotonically with the filler addition. In overall, all the investigated fillers with 10 wt% addition resulted in a reasonable sintering (over 95 %) and low dielectric constants (less than 6), demonstrating the feasibility of the investigated composites for application to a LTCC substrate material with a low dielectric constant.

• Applied Chemistry for Engineering
• /
• v.4 no.3
• /
• pp.497-504
• /
• 1993

The effect of DCCA (Drying Control Chemical Additives) on the drying of gel was investigated in order to determine an optimum drying condition of mullite precursor through sol-gel process. Aluminium sec-butoxide was synthesized from aluminium foil and then mullite powders were synthesized from Tetra-ethyl-ortho-silicate (TEOS) and the aluminium sec-butoxide. N, N-dimethyl formamide (DMF), Glycerol, 1, 4-Dioxane, and Oxalic acid were used as DCCA. Mullite powders that were calcined at 200, 900, 1100, and $1250^{\circ}C$ for 2hr were analysed by XRD, TG-DTA, FT-IR, and SEM in order to investigate structural change and characteristics of calcined powders. The results of this work showed that the drying time of gel was reduced to about half in the presence of 0.1mol DMF compared with the absence of DCCA and also calcined powders were obtained without remarkable structural change despite of the addition of DCCA.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.210-210
• /
• 2003

휘스커상의 뮬라이트의 생성온도와 속도는 출발물질로 사용되는 알루미나와 실리카의 화학적 순도, 입자크기 그리고 결정형태에 의존하며, 알루미나와 실리카의 조성비에 따라 생성되는 뮬라이트의 형태가 변한다. 각 원료에 대한 반응성을 관찰하기 위하여 출발원료인 Al(OH)$_3$, 비정질 SiO$_2$, AlF$_3$를 혼합 각각 단일조성과 2상 및 3상의 원료를 혼합 분쇄하여 분무건조한 조립분말을 5$0^{\circ}C$ 구간으로 나누어 상온에서 130$0^{\circ}C$까지 튜브 로에서 열처리하였다. Al(OH)$_3$와 AlF$_3$를 단독으로 열처리하였을 경우에는 안정한 상태로 열처리가 진행되었으나, 혼합하였을 경우에는 40$0^{\circ}C$ 이상의 온도에서 서서히 반응하였다. 각 온도구간에서 열처리한 시편은 미세구조 관찰과 상분석을 통하여 플루오르 토파즈와 휘스커상의 뮬라이트의 생성을 관찰하였으며, 생성된 휘스커 뮬라이트는 조립의 형상을 원형대로 보존하였으며, 조립의 강도를 측정하기 위하여, 초음파 분산기와, 초음파 Homgeniger를 이용하여 처리한 결과 대부분 원래의 형상을 유지하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.1
• /
• pp.47-56
• /
• 2017

In this study, the higher temperature thermal property of the fly ash-blast furnace slag system Geopolymer including alumina aggregate was investigated whether that Geopolymer will be or not useful as thermal-resistant construction materials. Under every mixing conditions, the crack on the surface of hardened body was not observed up to $800^{\circ}C$ and it corresponded with fact that level of changes was not significant before and after heating process. Residual compressive strength is most high when mixing Blast-Furnace Slag ratio is 60 wt% until temperature reaches $800^{\circ}C$. The major hydrates of hardened body of Geopolymer; amorphous halo pattern between $20{\sim}35^{\circ}$ (2theta) and mullite ($3Al_2O_3{\cdot}2SiO_2$) and quartz ($SiO_2$) was found during the experiment. Amorphous halo pattern was a aluminosilicate gel generated by geopolymeric polycondensation and it was found that the halo pattern of aluminosilicate gel was preserved up to $800^{\circ}C$. The patterns of aluminosilicate gel disappeared from $1,000^{\circ}C$ and crystal phases like gehlenite, calcium silicate, calcium aluminum oxide, microcline was observed with the increase of exposure temperature.