• Journal of the Korean Ceramic Society
• /
• v.17 no.1
• /
• pp.8-12
• /
• 1980

CaO was added to the $MgAlCrO_4$ spinel, a main component of the mag-chro refractroies, by 0, 1, 5 and 10 mol% before sintering at 135$0^{\circ}C$ in air. The X-ray diffraction analysis produced an additional X-ray diffraction pattern of 8CaO.$6Al_2O_3$.$2CrO_3$ besides that of $MgAlCrO_4$. The formation of 8CaO.$6Al_2O_3$.$2CrO_3$ was interpreted as due to the presence of CaO.8CaO.$6Al_2O_3$.$2CrO_3$ was unstable and easily vaporized. It was concluded that formation of the unstable pollutant 8CaO.$6Al_2O_3$.$2CrO_3$ could be prevented in reducing atmospheres. It was found that the basic refractories containing $Al_2 O_3 -CaO-Cr_2 O_3$ system would be more stable and much less toxic in reducing at mospheres than in oxidizing stmosphere.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.612-617
• /
• 2007

Both photoluminescence and thermal characteristics for $SrAl_2O_4:Eu^{+2},\;Dy^{+3}$ phosphors synthesized with various aluminum compounds (${\alpha}-Al_2O_3$, ${\gamma}-Al_2O_3$, amorphous-$Al_2O_3$ and $Al(OH)_3)$ were investigated in this study. The formation temperature of the host $SrAl_2O_4$ crystal is changed by these various aluminum compounds, as a result of the different thermal decomposition temperature of $SrCO_3$ phase. Among these compounds, the amorphous-$Al_2O_3$ phase shows the lowest formation temperature of the host $SrAl_2O_4$ crystal. The PL emission and excitation spectra of $SrAl_2O_4:Eu^{+2},\;Dy^{+3}$ phosphor are not affected by these aluminum compounds. After the removal of the Xenon lamp excitation (360 nm), however, the excellent longphosphorescent property of the phosphor is obtained by the amorphous-$Al_2O_3$ phase, although the decay time for all phosphors decrease exponentially.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.285-292
• /
• 1996

The effect of AlN on the thermal conductivity of aluminum oxide pressurelessly sintered at nitrogen atmos-phere was investigated. Increasing aluminium nitride content up to 1~10 mol% the thermal conductivity of $Al_{2}O_{3}$-AlN system was singnificantly decreased and was constant with adding 20 and 25 mol% aluminium nitride. The thermal conuctivity of $Al_{2}O_{3}$ containing 1~10 mol% the thermal conductivity of $Al_{2}O_{3}$-AlN system was singificantly decreased and was constant with adding 20 and 25mol% aluminum nitride. The thermal conctivity of $Al_{2}O_{3}$ containing 1~10 mol% AlN showed a maximum at $1700^{\circ}C$ and decrea-sed with increasing sintering tempertures. This phenomenon was attributed to $\alpha$-$Al_{2}O_{3}$ and ALON formed by reacting $Al_{2}O_{3}$ with AlN up to $1700^{\circ}C$ and the secondary phases such as ${\gamma}$-ALON ($9Al_{2}O_{3}$.AlN)and $\Phi$($5Al_{2}O_{3}$.AlN) phase above $1750^{\circ}C$ The thermal conductivity of $Al_{2}O_{3}$ containing 20 and 25 mol% AlN showed maximum value at $1800^{\circ}C$ Both $\alpha$-$Al_{2}O_{3}$ and ALON existed up to $1600^{\circ}C$ value at $1800^{\circ}C$ Both $\alpha$-$Al_{2}O_{3}$ and ALON existed up to $1600^{\circ}C$ while only AlON phase existed above $1650^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.731-739
• /
• 1993

R-curve measurements were performed on Al2O3(matrix)-ZrO2-SiC whisker composite and Al2O3-ZrO2, Al2O3-SiC whisker composites in the favor of comparing the effect of ZrO2 and SiC whisker, as a second phase, to Al2O3 matrix. Al2O3-SiC whisker and Al2O3-ZrO2-SiC whisker were fabricated by hot pressing at 1$700^{\circ}C$, 15MPa and Al2O3-ZrO2 by pressureless sintering at 1$600^{\circ}C$. A controlled flaw/strength technique was utilized to determine fracture resistance as a function of crack extension and R-curve behaviour was determined from the relationship which is KR=K0(Δa)m. R-curveresults were KR=6.173$\times$Δa0.031 for Al2O3-ZrO2, KR=18.796$\times$Δa0.172 for Al2O3-SiC whisker and KR=11.96$\times$Δa0.110 for Al2O3-ZrO2-SiC whisker composite. From the analysis of R-curve and expeirmental data above three composites, it is found that R-curve behaviour of Al2O3-ZrO2-SiC whisker composite was dominated initially by the strengthening effect of ZrO2 and after, some extended crack were influenced by the effect of SiC whisker. Analysis of SEM and X-ray data revealed that whisker bridging in the crack wake and whisker pull-out mechanisms were the main mechanism for the R-curve behaviour.

• Journal of the Korean Ceramic Society
• /
• v.22 no.6
• /
• pp.42-52
• /
• 1985

Several $Al_2O_3$-based polycrystalline which had different dopant ratio in the range of 0.5mol% were prepared by doping pure $Cr_2O_3$ $HfO_2$. Single crystalline which had same composition with above polycrystalline were made by means of floating zone method. This study examined the role of each dopant for enhancing the mechanical properties of $Al_2O_3$-based Ceramics. Optical micrographs $({ imes}200)$ of $Al_2O_3-Cr_2O_3$ single crystal showing not only radial crack (rc) on the specimen surface but median crack(mc) and lateral crack(lc) under surface at the edge of indentation mark. Fracture toughness of Al2O3-based Ceramics was increased with $ZrO_2$ content. Alloying effect of $Cr_2O_3$ contributed to the hardness of $Al_2O_3$ based ceramics.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.413-419
• /
• 2002

Particulate composites of $Al_2O_3$/TiC/SiC, $Al_2O_3$/TiC and $Al_2O_3$/SiC have been fabricated by hot pressing and their R-curve behaviors and mechanical properties were investigated. $Al_2O_3$ containing 30 vol% TiC particles showed higher toughness by 8% than that for monolithic alumina and its fracture strength was increased significantly by approximately 30%. On the other hand, the addition of 30 vol% SiC of $3{\mu}m$ in $Al_2O_3$ decreased the fracture strength slightly but induced a rising R-curve behavior owing to the strong crack bridging of SiC particles. In case of $Al_2O_3$/TiC/SiC, arising R-curve behavior was also observed and the fracture toughness reached 6.6 MPa${\cdot}\sqrt{m}$ at the crack length of $1000{\mu}m$, which was lower than that of $Al_2O_3$/SiC, however, while the fracture strength was higher by about 20%. The fracture toughness seemed to be decreased as smaller TiC particles roughened the SiC interface and pullout of the SiC particles for crack bridging became less active.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.238-239
• /
• 2018

This paper presents the synthesis results of CaO-Al₂O₃ system clinker using the CaCO₃ and the Al₂O₃ according to the synthesis methods dependent on the temperature. The purpose of this study is the formation of the CaO-Al₂O₃ system clinker containing high ratio of CaO·2Al₂O₃ (CA₂). The maximum sintering temperature for the synthesis of CaO-Al₂O₃ compounds was 1250℃, 1300℃ and 1400℃. The CaO-Al₂O₃ compounds was sintered at the maximum sintering temperature for three hours. After sintering, the compounds was analyzed using X-ray diffraction method. The 12CaO·7Al₂O₃ (C1₂A₇) and CaO·Al₂O₃ (CA) increased as elevating the maximum sintering temperature whereas the CA₂ decreased. Especially, at the 1250℃ of maximum sintering temperature, the un-reacted CaO and Al₂O₃ was identified.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.10
• /
• pp.1763-1770
• /
• 2007

Strong solid acid catalysts, NiO/Al2O3-TiO2/WO3 for ethylene dimerization were prepared by the addition of Al2O3 and the modification with WO3. The acid sites and acid strength were increased by the inductive effect of WO3 species bonded to the surface of catalysts. The larger the dispersed WO3 amount, the higher both the acidity and catalytic activity for ethylene dimerization. The addition of Al2O3 to TiO2 up to 5 mol% enhanced acidity and catalytic activity gradually due to the interaction between Al2O3 and TiO2 and consequent formation of Al-O-Ti bond.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2017

Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Thin layer of encapsulation film is required to preserve transparency yet protecting materials in it. Atomic layer deposition(ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. $Al_2O_3$ or $Al_2O_3/TiO_2/Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films. $Al_2O_3/TiO_2/Al_2O_3$ multilayer and 1.5 dyad layer of $Al_2O_3/polymer/Al_2O_3$ deposited by ALD was measured to have water vapor transmittance rate(WVTR) well below the detection limit($5.0{\times}10^{-5}g/m^2day$) of MOCON Aquatran 2 equipment.

• Composites Research
• /
• v.12 no.3
• /
• pp.36-44
• /
• 1999

The fabrication process of $Al_2O_{3p}/Al$ composite by in-situ process was investigated. The effects of processing variables such as addition type and content of Mg, processing temperature and time on the infiltration behavior of molten Al, microstructure and hardness were investigated. When the pure Al was infiltrated into mixtures of Mg and $Al_2O_3l$ powder, processing temperature required to spontaneous infiltration was decreased, and the content of Mg was the most powerful variable for infiltration of molten Al. But when the Al-Mg alloy was infiltrated into $Al_2O_3l$ particles, infiltration ratio indicated nearly same value regardless of Mg content in alloy and processing temperature, and critical processing temperature required to spontaneous infiltration was $800^{\circ}C$. The $Al_2O_{3p}/Al$ composites which were fabricated by mixtures of Mg and $Al_2O_3l$ powders resulted in high hardness value, but hardness values were scattered due to non uniform dispersion of $Al_2O_3l$ particles by excessive reaction of Mg.