• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.816-825
• /
• 1994

The purpose of this study is to develop the non-destructive material evaluation method of aluminum alloy base metal matrix composite(MMC) by ultrasonics. Five aluminum base MMC specimens were fabricated in which the fractional ratios of fiber were changed from 0% to 31%. Relations among acoustic properties, microstructural features and elastic constant were compared. The ultrasonic velocity method was useful for nondestructive elastic constant measurement of composite materials, since the method had as same accuracy as conventional strain measurement method. Furthermore, velocity, attenuation and backscattering behaviors for each specimen also related to fractional ratio of fiber and these relations could utilize ultrasonic non-destructive evaluation of fiber structure in MMC.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.364-371
• /
• 2013

The sintering behavior of monolithic SiC is examined using the binary sintering additive of $Al_2O_3$-rare earth oxide ($RE_2O_3$, where RE = Sc, Nd, Dy, Ho, or Yb). Through hot pressing at 20 MPa and $1750^{\circ}C$ for 1 h in an Ar atmosphere for 52 nm fine ${\beta}$-SiC powder added with 5 wt% sintering additive, a SiC density of > 97% is achieved, which indicates the effectiveness of $Al_2O_3-RE_2O_3$ system as a sintering of additive for SiC. Based on this result, 7 wt% of $Al_2O_3-Sc_2O_3$ is tested as an additive system for the fabrication of a continuous SiC fiber-reinforced SiC-matrix composite ($SiC_f$/SiC). Electrophoretic deposition combined with the application of ultrasonic pulses is used to efficiently infiltrate the matrix phase into the voids of $Tyranno^{TM}$-SA3 fabric. After hot pressing, a composite density of > 97% is obtained, along with a maximum flexural strength of 443 MPa.

• 멤브레인
• /
• 제32권2호
• /
• pp.116-125
• /
• 2022

본 실험에서는 α-Al₂O₃ 세라믹 중공사를 지지체로 사용하였고, 무전해 도금을 통해 Pd 및 Pd-Ag가 도금된 수소 분리막을 제조하였다. Pd-Ag 분리막은 Pd와 Ag 합금 형태로 만들기 위하여 500℃, 10 h 동안의 annealing 과정을 거쳤으며, EDS (Energy Dispersive X-ray Spectroscopy) 분석을 통해 Pd-Ag 합금이 되었다는 것을 확인하였다. 또한, SEM (Scanning Electron Microscope) 분석을 통해 제조된 Pd 및 Pd-Ag 도금층의 두께는 약 8.98, 9.29 ㎛으로 측정되었다. 제조된 수소 분리막은 350~450℃, 1-4 bar의 범위에서 수소 단일 가스, 혼합가스(H₂, N₂)를 이용하여 수소 투과 실험을 진행하였다. 수소 단일 가스에서 Pd와 Pd-Ag 분리막은 최대 각각 21.85, 13.76 mL/cm²·min의 flux를 가지며, 혼합가스에서는 450℃, 4 bar의 조건일 때, 1216, 361의 separation factor가 각각 나오는 것을 확인하였다.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.118-123
• /
• 2004

A formation of aluminum hydroxide by hydrolysis reaction in the water has been studied by using nano aluminum powder fabricated by pulsed wire evaporation(PWE) method. The hydroxide type and morphology depending on temperature and pH were examined by structural analysis. The Boehmite($Al_2O_3$.$H_2O$ or AIO(OH)) was predominantly formed in high temperature region over 4$0^{\circ}C$, while the Bayerite($Al_2O_3$.$H_2O$ or $Al(OH)_3$) below $30^{\circ}C$ of hydrolysis temperature. The Boehmite formation was preferred to the Bayerite in acidic solution in the same hydrolysis temperature. The slowly formed Bayerite phase showed facet crystalline structure, while the fast formed Boehmite was fine fiber with a large aspect ratio of several nm in diameter and several hundred nm in length, and with much larger specific surface area(SSA) than that of Bayerite. The highest SSA was about $420m^2$/g.

• 한국재료학회지
• /
• 제9권3호
• /
• pp.315-321
• /
• 1999

금속기지 복합물은 구조용 재료로서 매우 우수한 성질을 지니고 있어 광범위하게 연구되어져 왔다. $Al_2O_3$와 SiC는 그들의 우수한 기계적 특성 때문에 일반적인 보강재로서 사용되어져 왔다. 그러나 이들 세라믹 보강재는 비싼 재조 비용 때문에 특별한 목적을 위해서만 한정되어 사용되어져 왔다. 본 연구에서는 우리는 Al 합금기지 복합물에서 SHS법에 의해 합성된 $Al_2O_3$-SiC 분말의 보강재로서의 응용 가능성을 살펴보았다. 또한 $Al_2O_3$단섬유를 Al기지 하이브리드 복합물에 적용하기 위하여 합성된 분말과 함께 첨가하였다. 25vol% 강화재의 복합물을 제조하기 위하여 용탕단조법을 사용하였다. 미세구조와 결정구조는 SEM, OM 그리고 XRD로 관찰하였고 압축시험과 마모시험으로 기계적인 성질들을 조사하였다.

• 한국주조공학회지
• /
• 제21권3호
• /
• pp.163-178
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. Aluminum matrix composite automotive parts, such as diesel engine pistons or engine blocks are produced using squeeze casting apparatus or pressure die-casting apparatus. But the solidification process gets complicated with manufacturing parameters and the factors for porosity formation have not fully understood yet. In this study the formation of porosity during squeeze infiltration has been studied experimentally to achieve an improved understanding of the squeeze infiltration process for manufacture of short-fiber-reinforced components, particularly the mechanism of porosity formation. Al-based MMCs produced under a range of conditions were examined metallographically and the porosity characterised;a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The densimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.

• 한국산학기술학회논문지
• /
• 제5권2호
• /
• pp.103-107
• /
• 2004

산업폐수중 anion인 chromate(CrO4-²)처리에 필요한 기능성소재로 이온교환 및 흡착기능을 가진 PAN계 이온교환섬유를 제조하고 성능평가를 실시하여 소재특성을 연구하였다. Poly(acrylonitrile)섬유와 diethyletriamine을 /sup AlCl₃ 촉매 하에서 반응시켜 poly (acryloamidino diethylenediamine)을 제조하고, /sup 13/C-NMR분석으로 확인하였다. 온도에 따른 polymer의 개질반응 정도를 FT-IR 분석으로 조사하여 개질반응의 최적 온도 120℃를 확인하였다. 개질반응된 polymer의 chromate 최대 흡착량을 분석하고, 음이온 흡착에 대한 소재특성을 pH별로 실시하였다. poly(acryloamidino diethylenediamine)/CrO4-² coordinaion 과정의 FT-IR spectra 분석하여 분자내, 분자간 결합형태를 밝히고 coordination된 구조를 제시하였다.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1999년도 PROCEEDINGS OF 99 INTERNATIONAL CONFERENCE OF THE KACG AND 6TH KOREA·JAPAN EMG SYMPOSIUM (ELECTRONIC MATERIALS GROWTH SYMPOSIUM), HANYANG UNIVERSITY, SEOUL, 06월 09일 JUNE 1999
• /
• pp.403-418
• /
• 1999

Fiber growth of Al2O3/R-Al-O(R=Y, Gd, Dy, Ho, Er) eutectic by the micro-pulling down methods is described. The thermal stability and strength at elevated temperature of each material is evaluated in relation to the microstructure. PACS: 81.05 Mh, 81.10 Fq, 81.30-t.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.46-49
• /
• 2003

Aluminum based metal matrix composites(MMCs) are well known for their high specific strength, stiffness and hardness. They are gaining further importance because of their high wear resistance. In this study, Al/Saffil-20%, Al/Saffil-5%/Al2O3(particle type)-15% and Al/Saffil-5%/SiC(particle type)-15% hybird MMCs' wear behavior were characterized by the pin-on-disk test under various normal load The superior wear resistance was exhibited at Al/Saffil-5%/SiC(particle type)-15% MMCs. And this MMCs' predominant wear mechanism is subsurface cracking in the low load wear regime. Others(Al/Saffil-20%, Al/Saffil-5%/Al2O3(particle type)-15%) showed the similar wear resistance with each other at the same test condition. In the low load & room temperature condition, the wear resistance was improved due to the high hardness of the ceramic reinforcements. As the test load increased, the wear properties were governed by the wear properties of matrix.

• Composites Research
• /
• 제22권5호
• /
• pp.15-23
• /
• 2009

가압주조법으로 제조한 $Al_2O_3$ 섬유와 SiC 입자 혼합 보강 금속복합재료(MMCs)의 상온과 고온에서 윤활마모특성을 조사하였다. 마모시험은 거리와 온도의 변화에 따라 속도를 고정시켜 25Kgf의 하중하에서 수행하였으며 MMCs의 시험편은 가압의 수평(PR)방향과 수직(N)방향에서 채취하였다. 혼합비의 영향을 관찰한 결과 상온에서는 20%섬유만 보강한 PR방향 MMCs의 마모거동은 N방향 보다 우수한 결과를 보였으나, 혼합보강 MMCs는 반대로 나타내었다. 고온($100^{\circ}C$)에는 모든 MMCs에서 PR방향의 마모거동이 N 방향보다 우수한 결과를 보인 것은 보강재와 마찰면간 윤활필름이 강호작용에 기인한 것으로 밝혀졌다. $150^{\circ}C$에서는 혼합 MMCs의 마모거동은 온도영향으로 PR이 N 보다 우수한 결과를 보였다.