• 한국세라믹학회지
• /
• 제30권11호
• /
• pp.962-966
• /
• 1993

Effect of Fe content on the electrical properties of Zn2Y (Ba2Zn2Fe12O22) was studied by investigating X-ray diffraction patterns, microstructure and resistivity of samples. When x(Ba2Zn2Fe12＋xO$\delta$) is between ＋1 and -1, Zn2Y single phase was obtained and electrical resistivity was inversely proportional to Fe content. The possible defect model of Zn2Y was proposed based on the observation. When x<-1 or x>1, second phase(ZnFe2O4 for x<-1, ZnFe2O4 and Ba3Zn3Fe24O41 for x>1) were observed and the electrical resistivity was inversely proportional to the sample density. The activation energy of electrical conductivity of the stoichiometric Zn2Y was 0.49eV below 20$0^{\circ}C$ and 0.07eV above 50$0^{\circ}C$.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.316-325
• /
• 1986

본 연구에서는 이상배합조직강에 있어서 피로균열진전거동의 미시조직 의존 성을 밟히기 위하여 제이상 마르텐사이트가 모상 페라이트를 둘러싼 마르텐사이트페라 이트 복합조직강을 준비하고 미시조직이 각각 다른 4종류의 시험편에 대하여 피로시험 을 실시한후 이에 의해 얻어진 피로균열진전속도를 균열휨과 균열닫힘을 통하여 검토 하였다.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.4-17
• /
• 1984

Overlaid weld metals of austenitic stainless steel in a pressure vessel of power reactor are usually post-weld heated for a long period of time after welding. The PWHT is considered as a kind of sensitizing and it is important to check the soundness of the weld metal after PWHT, especially about the precipitation of carbides. The purpose of this report is to obtain information on the relation between the change of microstructure and Post-Weld Heat Treatment in the overlaid weld metals. Metallurgical aspects of the problem on austenitic stainless steel heated at $625^{\circ}C$, $670^{\circ}C$, $720^{\circ}C$ and $760^{\circ}C$ for 3, 10, 30, 100 and 300 hours have been investigated by means of optical-micrography, micro-hardness measurement, scanning electron microscope and electron-probe micro analysis. From the results obtained, the following conclusions are drawn; 1) The PWHT above $625^{\circ}C$ for a long time causes a diffusion of carbon atoms from low alloy steel into stainless steel, and consequently carbon is highly concentrated at the boundary layer of stainless steel. 2) C in ferritic steel migrated to austenitic steel and carbides precipitated in austenitic steel along fusion line. At higher temperatures, the ferrite grains coarsened in the decarburized zone. 3) In the change of microstructure of stainless steel overlaid weld metal, the width of carbides precipitated zone and decarburized zone increased with increase of PWHT temperature and time. 4) At about $625^{\circ}C$ to $760^{\circ}C$, chromium carbides, mainly $M_{23} C_6$, precipitate very closely in the carburized layer with remarkable hardening. 5) Precipitation of delta ferrite from molten weld metal depends on solidification phenomenon. There was a small of ferrite near the bond in which the local solidification time was short, comparing with after parts of weld metal. Shape and amount of ferrite were not changed by Post-Weld Heat Treatment after solidification.

• 한국자기학회지
• /
• 제27권1호
• /
• pp.23-29
• /
• 2017

시료 크기별 자화 역전과 자기 상호작용이 보자력에 미치는 영향을 조사한 결과, 자구생성보다 자벽고착에 의한 자화 역전 현상이 지배적인 시료일수록 보자력과 각형비가 컸다. 이와 같은 현상은 자벽이 낟알 경계면이나 시료 내부에 존재하는 고착점에 강하게 포획되기 때문인 것으로 판단된다. 한편 자기 상호작용을 분석한 결과, 시료의 크기에 무관하게 모든 시료는 쌍극자 상호작용이 지배적인 상호작용 기구이며, 쌍극자 상호작용이 강한 시료일수록 보자력이 작았다. 따라서 보자력은 자화 역전 현상, 자기 상호작용 기구와 세기에도 깊이 관련됨을 알 수 있다.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.208-215
• /
• 1992

Concept of primary solidification mode control was adopted to obtain optimal solidification crack resistance, hot ductility, corrosion resistance and toughness for austenitic stainless steel. By controlling primary solidification phase as primary $\delta$ and containing no ferrite at room temperature, optimal solidification crack resistance, hot ductility, corrosion resistance and cryogenic toughness could be obtained. The optimum chemical composition of austenitic stainless steel ranges 1.46~1.55(Creq/Nieq ratio) calculated by Schaeffler's equation.

• 수산해양기술연구
• /
• 제26권4호
• /
• pp.372-379
• /
• 1990

The effect of primary solidification phase on the solidification cracking sensitivity, corrosion resistance and toughness at cryogenic temperature was investigated for the austenitic stainless steel welds. The conclusions were summarized as follows; 1. Soldification crack sensitivity of austenitic stainless steel welds depends on the primary solidification mode. 2. Austenitic stainless steels were very susceptible to solidification cracking in case of solidification as primary ${\gamma}$ and immune when solidified as primary $\delta$. 3. When the ratio of Creq/Nieq is in the range of 1.46 to 1.55, the most resistance against solidification cracking was obtained. These results agreed well with the relationship between primary solidification mode, corrosion resistance and toughness at cryogenic temperature. 4. Optimum toughness, corrosion and solidification cracking resistance can be obtained when alloys having chemical compositions described above and solidifies as primary $\delta$ containing no ferrite at room temperature.

• 전자통신동향분석
• /
• 제18권6호통권84호
• /
• pp.41-48
• /
• 2003

본 논문은 아이솔레이터의 소재 파라미터에 의한 삽입손실 영향에 대하여 서술하였다. 본 논문에서는 페리자성공명반치폭($\Delta$Η), 유전손실, 자계세기 그리고 포화자화에 대한 아이솔레이터 삽입손실의 관계를 알아 보았고, 또한 공진 아래 모드를 사용한 아이솔레이터의 온도안정화 연구 및 구조설계에 대하여알아 보았다. 아이솔레이터의 온도특성은 영구자석, YIG(Yttium Iron Garnet) 페라이트 그리고 공진기로사용되는 도체 등에 의한 변화에 대하여 본 논문에서는 실험시제품을 제작하여 측정 분석하였다. 측정결과 시뮬레이션 결과와 실험시제품 측정결과가 거의 일치하는 것을 알 수 있었다. 삽입손실 0.18~0.24dB, 반사손실 27dB, 아이솔레이션 27dB 그리고 대역폭 500MHz를 얻을 수 있었다. 이때 실험에 사용한 소재 파라미터는 포화자화 550G, 유전손실, $0.0004\Delta$Η20, 유전율 14로 하였다. 또한 온도안정화실험에서는 구조를 개선하여 온도안정화를 이루었다.

• 열처리공학회지
• /
• 제3권2호
• /
• pp.37-44
• /
• 1990

The effect of the microstructural change on the near threshold fatigue crack growth rate in SM40C steel has been studied using the ${\Delta}K$ decreasing method. Below the total strain amplitude of 0.56%, cyclic softening occured, whereas above this value cyclic hardening occurred in the pearlitic lamellar structure. However, in the spherodized structure the cyclic hardening solely occurred. The crack growth rate in the near-threshold region was decreased with increasing prior austenite grain size and this was due to surface roughness. The crack growth rate of the spherodized structure was lower than that of the pearlite lamellar structure and the ${\Delta}K_{th}$ of the former was higher than that of the latter. It was understood that the crack propagates preferentially through the ferrite phase. The intergranular facets in the near-threshold region appeared in the spherodized structure.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.137-143
• /
• 2003

The air gap between the metal and mold, formed by shrinkage during solidification, causes surface and subsurface cracks in the continuous casting process. Molten crack on the surface might also occur due to improper heat transfer between them. In order to compensate the air gap in mold design, the thermal contraction is an essential factor. In this study, the thermal contraction and expansion behaviors were examined from the ($\alpha$ and pearlite)/${\gamma}$ to ${\gamma}$/$\delta$ transformations in continuous casting steels by the commercial dilatometer and the self- assembled dilatometer with laser distance measurement. It was found that the thermal contraction and expansion behaviors were very dependant on the phase transformation of the ${\gamma}$/$\delta$ as well as ($\alpha$ and pearlite)/${\gamma}$. The sudden volume change from $\delta$ to ${\gamma}$ which might cause cracks in the continuous casting process, was observed on cooling just below the melting temperature by the self-assembled dilatometer.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.248-261
• /
• 1999

The fatigue life of mechanical components and structures has been influenced by mechanical, material and environmental conditions. It is important to search out the load type and size for accurate cause of fracture at the damaged surface of material. The fractographic method by x-ray diffraction can utilize residual stress $\sigma$_r and half-value breadth B and find out the types and the mechanical conditions of fracture. This study showed the relationship between fracture mechanical parameters $\Delta$K, $K_{max}$ and X-ray residual stress $\sigma$_r for normalized SS41 steel with homogeneous crystal structure and M.E.F. dual phase steel(martensite encapsulated islands of ferrite). The fatigue crack propagation tests were carried out under stress ratios 0.1 and 0.5. The x-ray diffraction technique according to crack propatation direction was applied to fatigue fractured surface. Residual stress $\sigma$_r was independent on stress ratios by arrangement of $\Delta$K. The equation of $\sigma$_r$\Delta$K was established by the experimental data. Therefore, fracture mechanical parameters can be estimated can be estimated by the measurement of X-ray parameters.