• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.155-160
• /
• 2002

Metal matrix composites had generated a lot of interest in recent times because of significant in specific properties. It was also highlighted as the materials of frontier industry because strength, heat-resistant, corrosion-resistant, wear-resistant were superiored. In this study the strength properties of $Al_{18}B_4O_{33}/AC4CH$ were represented mixing the binder of $Al_2O_3$ and $TiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_4O_{33}/AC4CH$ was fabricated at the melt temperature of $760^{\circ}C$ the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa and observed SEM. Fatigue crack growth rate tests on compact tension specimen(half-size) of thickness 12.5mm were conducted by using sinusoidal waveform. Compact tension specimens(half-size) were used and fatigue crack growth rate da/dN and stress intensity factor range ${\Delta}K$ were analyzed concerning to the R value of 0.1 and 0.05. In order to find out the value of ${\Delta}K$, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. As the results of this study, Fatigue crack growth rate increased with in creasing the load ratio, Consequently, At equivalent stress intensity factors, the fatigue crack growth rates in MMC were faster than those of AC4CH alloy. then the fatigue life and the fatigue crack growth rate was investigated using scanning election microscopy(SEM)

• Journal of Welding and Joining
• /
• v.12 no.3
• /
• pp.82-89
• /
• 1994

In this paper the effect of stress ratio on the fatigue crack growth rate of aluminum alloy A5083-O was examined. The fatigue tests were carried out using CCT (center cracked tension) specimens and CT(compact tension) specimens which were subjected to 0.5 and -1.0 stress ratio respectively. The obtained results are as follows; 1) The $\DeltaK_{th}$ as the function of stress ratio R was introduced in evaluating the fatigue crack growth rate of A5083-O. 2) A new model evaluating the effect of stress ratio on the fatigue crack growth rate was developed over the region of low and high propagation rate.

• Electrical & Electronic Materials
• /
• v.10 no.5
• /
• pp.434-439
• /
• 1997

It this paper, the piezoelectric and electro-induced strain properties of (P $b_{1-}$2x/3/B $i_{x}$ )[N $i_{1}$3/N $b_{2}$3/)$_{0.4}$( $Ti_{0.6}$Z $r_{0.4}$)$_{0.6}$] $O_3$ceramics (x=0, 0.005, 0.02) were investigated with the substitution of B $i^{3+}$, and the feasibility of the application for bimorph actuator was evaluated by measuring the dynamic properties of the piezoelectric bimorph fabricated with above ceramics. Dielectric constant was enhanced with the increase of B $i^{3+}$ substitution, and appeared the maximum value of 5032 at x=0.01 composition. Increasing the substitution of B $i^{3+}$, the electromechanical coefficient( $k_{p}$ , $k_{31}$ ) was increased up to the substitution of 0.5 mol% B $i^{3+}$, showed the value of 0.656, 0.439, respectively. The piezoelectric constant( $d_{33}$ $d_{31}$ ) had the highest value of 344, 825 with the substitution of 0.5 mol% B $i^{3+}$. The strain, generated by 60 Hz AC electric field, had the largest value of 1200($\times$10$^{-6}$ $\Delta$1/1) in the composition with the substitution of 0.5 mol% B $i^{3+}$. The dynamic properties of the bimorph actuator, fabricated with the composition substitution of 0.5 mol% B $i^{3+}$, showed the largest value of 325 $\mu$m at $\pm$150 V square pulse. square pulse.are pulse..

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.1
• /
• pp.13-16
• /
• 2017

In this study, in order to develop composition ceramics for refrigeration device application, $Ba(Ti_{0.9}Zr_{0.1})O_3$ composition was fabricated using conventional solid-state method. Electrocaloric effect of this ceramic was investigated using the characteristics of P-E hysteresis loops at wide temperature range from room temperature to $150^{\circ}C$. Curie temperature of $Ba(Ti_{0.9}Zr_{0.1})O_3$ ceramics showed $80^{\circ}C$. The maximum value of ${\Delta}T=0.12^{\circ}C$ in ambient temperature of $115^{\circ}C$ under 30 kV/cm was appeared. It is concluded that $Ba(Ti_{0.9}Zr_{0.1})O_3$ ceramics can be applied as refrigeration device application.

• Korean Journal of Acupuncture
• /
• v.29 no.3
• /
• pp.467-475
• /
• 2012

Objectives : The aim of this study was to examine the effects of Acupuncture at the GV20 and GV22 on normal human beings using power spectrum analysis. Methods : Electroencephalogram(EEG) power spectrum exhibits site-specific and state-related differences in various frequency bands. 8 channels Background Electroencephalogram (EEG) was carried out in 30 subjects(24 females and 4 males). Results : In ${\delta}$(theta) band, the power values decreased significantly at the 8-channel average value(p=0.03) and especially at T3(p=0.02), T4(p=0.001) and P3(p=0.03). In ${\alpha}$(alpha) band, the power values have no significant changes. In ${\beta}$(beta)band, the power values increased significantly at the 8-channel average value (p=0.02) and especially at T4(p=0.003), P3 (p= 0.03) and P4(0.02). In ${\beta}/{\delta}$(beta/theta) ratio, the value increased significantly at the 8-channel average value(p=0.002) and especially at Fp2(p=0.05), F4(p=0.007), T3(0.012), T4(0.005), P3 (0.007) and P4(0.03) Conclusions : Through this data, we conclude that acupuncture at the GV20 and GV22 on normal human beings could have possibility to awake the cerebral cortex by the functional mechanism.

• Economic and Environmental Geology
• /
• v.34 no.5
• /
• pp.471-483
• /
• 2001

The pH values of the mine and surface water from the Tohyun mine creek were higher compared with those of groundwater, and 2nd round samples in same sites were even alkaline. The stream and mine waters belong to the characteristics of (Ca+Mg)-(SO$_4$) and (Ca+Mg)-(HCO$_3$) types, and groundwaters have to the (Ca+Mg+Na+K)-(HCO$_3$+SO$_4$) type. As the 2nd samples. concentrations of mostly anions are increasing compared with the forder samples. However, the mostly cation concentrations are decreasing. The hydrogeochemistry indicate that water quality is different chemical characteristics and evolution trends. The range of $\delta$D and $\delta$$^{18}$ valutes (relative to SMOW) in the waters are shown in -62.2 to -70.1$\textperthousand$, and -8.1 to -9.4$\textperthousand$. The values are plowed parallel to $\delta$D=8$\delta$$^{18}$ O+ (6$\pm$4). The d values of groundwater show 2.4, which is lower than the surface (5.2) and mine (7.6) waters. Strontium concentra titans range from 0.025 to 11.844 mg/$\ell$ in all kinds of water samples, but the groundwater has the highest contents The $^{87}$ Sr/$^{86}$ Sr ratios (0.7115 to 0.7129) show more lightened to the groundwater. The $\delta$$^{18}$ O value, Ca and Sr contents are decreased with $^{87}$ Sr/$^{86}$ Sr increasing, because it is support to the altitude effects of the sampling sites rather than a water-rock interaction of environmental isotope. Using computer code of WATEQ4F, saturation indices of albite, Quartz, gibssite and gypsum are calculated to be soluble. The calcite and dolomite show super saturation state, however, clay mineral species are plotted boundary between undersaturation and supersaturation. In the Tohyun mine creek, reaction materials with ore wastes arid precipitation have influence upon increasing EC and TDS of the waters independent of pH. The SO$_4$ concentrations in the mine water is 181.845 mg/$\ell$. This is abruptly increase in surface water and then detected 249.727 mg/$\ell$ in the groundwater. As a results of the calculated sulfate mineral solubilities, the sulfate ions became saturation states an above 150 mg/$\ell$ concentrations.

• Economic and Environmental Geology
• /
• v.32 no.4
• /
• pp.385-398
• /
• 1999

The Narim gold mine is located approimately 200km southeast of Seoul within the Muju mineralized district of the Sobaegsan gneiss complex, Korea. Environmental geochemistry were undertaken for various kinds of water (surface, ground and mine water) collected of April, September and November in 1998 from the narim mine creek. Hydrogeochemical compositions of water samples are characterized by the relatively significant enrichment of Na+K, alkali ions, $HCO_{3}$, $NO_{3}$, Cl and F in groundwater, wheras the mine and surface waters are relatively enriched in Ca+Mg, hea표 metals and $SO_{4}$. Therefore, the groundwaters belong to the (Na+Ca)-( $HCO_{3}+SO_{4}$) type, respectively. The pH and EC values of the non-mining creek surfers are relatively lower compared with those of the surface water of the mine and ore dump area. The d values ($\delta$D-8$\delta^{18}$O) of all kinds of water from the Narim mine creek are 5.8 to 13.1 The range of $\delta$D and $\delta^{18}$O values (relative to SMOW) are shown in distinct two groups as follows: for the April waters of -64.8 to -67.8$\textperthousand$ and -9.6 to -10.0$\textperthousand$(d value=10.1 to 13.1), and for the November waters of -65.9 to -70.2$\textperthousand$ and -9.3 to -9.6$\textperthousand$ (d value=5.8 to 7.9), respectively. This range variation indicates that two group water were composed of distinct waters with seasonal difference. Geochemical modeling showed that mostly toxic metals (As, Fe, Mn, Ni, Pb, Zn) may exist largery in the from of metal $(M2^+)$ and metal-sulfate $(MSO_4\;^{2-$\mid$),\; and \;SO_4^{2-$\mid$}$ concentration influenced the speciation of heavy metals in the meteoric water. These metals in the groundwater could be formed of $CO_3 \;and \;(OH)_3$ complex ions. Using computer program, saturation index of albite, calcite, dolomite in meteoric water show undersaturated and progreddively evolved toward the saturation state, however, ground and mine water are nearly saturated. The gibbsited water-mineral reaction and stabilities suggest that the weathering of silicate minerals may be stable kaolinite, illite and Nasmectite. The clay minerals will be transformed to more stable kaolinite owing to the contiunous reaction.

• The Korean Journal of Ceramics
• /
• v.7 no.1
• /
• pp.20-25
• /
• 2001

PbTiO$_3$ thin films were prepared by low-pressure thermal plasma deposition on (100)Pt/(100)MgO substrates. Mist of source material in which metal alkoxides are dissolved in 2-methoxyethanol was introduced into plasma through heating furnace and deposited onto substrates at $600^{\circ}C$. As-deposited PbTiO$_3$/Pt/MgO thin film prepared at 1.33$\times$10$^4$ Pa was grown epitaxially, but was consisted of many rectangular shaped grains, with many grain boundaries and it was impossible to measure electric properties. As-deposited film prepared at 1.00$\times$10$^4$ Pa showed weak peaks of X-ray diffraction and the film was not grown epitaxially. On the other hand, the film after annealed at $700^{\circ}C$ showed strong diffraction peaks and epitaxial growth was also observed. For annealed film, moreover, no clear grain boundaries were observed. The value of ${\varepsilon}_r$, tan${\delta}$, Pr and Ec of annealed film were 160, 3.2%, 10.4${\mu}$C.cm$^-2$ and 51.2kV.cm$^-1$, respectively. Since the composition, Pb/Ti, measured by EDS attaching to SEM changed point by point, the distribution of composition in annealed film was investigated and found out several relations between composition and electric properties. At stoichiometric composition, Pr and Ec showed the lowest value and they gradually became large as composition deviated from stoichiometric one. Moreover, the value of ${\varepsilon}_r$ became gradually large as the ratio of Ti became high.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.6
• /
• pp.618-622
• /
• 1997

The polysiloxane-bridged dinuclear metallocenes $[(SiMe_2O)_n-SiMe_2(C_5H_4)_2][(C_9H_7)ZrCl_2]_2$ (n=1 (7), 2 (8), 3 (9)) have been generated as a model complex for the immobilized metallocene at silica surface by treating the respective disodium salts of the ligands with 2 equivalents of $(C_9H_7)ZrCl_3$ in THF. All three complexes are characterized by $^1H$ NMR and measurement of metal content through ICP-MS. It turned out that the values of ${\Delta}{\delta}=[{\delta}_d-{\delta}_p]$, the chemical shift difference between the distal $({\delta}_d)$ and proximal $({\delta}_p)$ protons, for the produced dinuclear compounds (0.47 for 7, 0.49 for 8, and 0.5 for 9) were larger than the Δδ value of the known ansa-type complex holding the same ligand as a chelating one, that is just the opposite to the normal trend. In order to compare polymerization behavior of the dinuclear metallocene with the corresponding mononuclear metallocene, (Cp)$(C_9H_7)ZrCl_2$ was separately prepared. To investigate the catalytic properties of the dinuclear complexes and mononuclear metallocenes ethylene polymerization has been conducted in the presence of MMAO. The polymerization results display the typical activity dependence on polymerization temperature for all complexes. The most important feature is that the polymers from the dinuclear metallocenes represent enormously improved molecular weight compared with the polymer from the corresponding mononuclear metallocene. In addition, the influence of the nature of the bridging ligand upon the reactivities of the dinuclear metallocenes has also been observed.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.203-209
• /
• 1999

LaAlO3d single phase used as the butter layer on Si wafer for YBa2Cu3O7-$\delta$ superconductor application were prepared by solid state reaction method and by self-sustaining combustion process. The microstructure and crystallity of synthesiszed LaAlO3 powder studied using scanning electron microscope (SEM) and X-ray diffractometer(XRD), specific surface area and sintering characteristics fo powder were investigated by Brunauer-Emmett-Teller (BET) method and dilatometer respectively. In solid state reaction method, it is difficult to obtain LaAlO3 single phase up to 150$0^{\circ}C$ period. However, in self-sustaining combustion process, it is to easy to do it only $650^{\circ}C$. Based on the results of analysis of dilatometer it is easier to obtain high sintering density (98.87%) in self-sustaining combustion process than in the solid state reaction method. This reason is that the average particle size prepared by self-sustaining combustion process is nano crystal size and has high specific surface are value(56.54 $m^2$/g) compared with that by solid state reaction method. Also, LaAlO3 layer on the Si wafer has been achieved by screen printing and sintering method. Even though the sintering temperature is 130$0^{\circ}C$, the phenomena of silicon out diffusion in LaAlO3/Si interphase are not observed.