A term of GNSS(Global Navigation Satellite System) is widely used to represent a navigation method for global area using satellite in space orbit 1his system can provide accurate and continuous position, and timing sources synchronized to UTC. There are, however, certain disadvantage that system can not operate without line of sight environment to satellite, or system failure of either satellite or control station. It is the pseduolite technology for using indoor and also for back-up equipment of foreign system failure. Especially, ocean applications widely use the GNSS system for navigation, surveying, timing, and management of traffic, so, system failure of GNSS will be very critical problem to affect many aspects of ocean field. In this paper, we experimented the pseudolite technology for several application field to compare the result in different environment. We used the common CDGPS algorithm for in-door navigation and experimented in ocean engineering basin with metallic wall and gymnasiums with concrete wall. We also investigated the comparison result and considerations for ocean applications of pseudolite technology.

Soil, ground water and sea bed are exposed to continuous accumulation of polluted materials causing serious environmental damage. It has been reported that such pollution causes a massive mortality of fish stock in rivers by the resuspension of toxic chemicals during strong wind conditions. Therefore, it becomes apparent that there is an immediate demand for the restoration treatment of polluted river bed (or sea bed) sediment layers. Pollution levels of major rivers and ports such as Pal-dang, Kyung-an rivers, Ma-san port are becoming public concern and are posing a serious environmental threat. In particular, the pollution of Shi-hwa river has become a nation wide issue for last few years. In spite of such public concern, the pollution level of such rivers or port are getting worse everyday. In this study, an environmentally sound engineering package is introduced which helps to restore the polluted river bed or sea bed sediments. This engineering package is consisted of a suction facility followed by a series of mechanical, chemical as well as biological treatment units. The suction facility is designed to minimize the secondary pollution due to the resuspension of toxic materials during suction. The sea bed cleaning engineering package is designed to be installed on the top of a floating barge. Such combination of environmental plant and shipbuilding technology provides a cost-effective solution, minimizing the cost involved in the transportation between suction and treatment facilities.

Mechanical design of a deepwater pipeline wall thickness was performed by using the recent design rules. Characteristics and limitations of the new design rules were identified through a case study of a deepwater oil pipeline in the Gulf of Mexico. A design procedure was established for mechanical design of deepwater pipeline wall thickness. Comparison of the new API and DNV codes are presented.

This paper describes the machining characteristics of the $MoSi_2$ based composites by electric discharge drilling with various tubular electrodes, besides, Hardness characteristics and microstructures of $Nb/MoSi_2$ laminate composites were evaluated from the variation of fabricating conditions such as preparation temperature, applied pressure and pressure holding time. $MoSi_2$ -based composites has been developed in new materials for jet engine of supersonic-speed airplanes and gas turbine for high- temperature generator. Achieving this objective may require new hard materials with high strength and high temperature-resistance. However, With the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material, the tool electrode being almost non-unloaded, because there is no direct contact between the tool electrode and the workpiece. By combining a nonconducting ceramics with more conducting ceramic it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and $MoSi_2$ powder was an excellent strategy to improve hardness characteristics of monolithic $MoSi_2$. However, interfacial reaction products like (Nb, Mo)$SiO_2$ and $Nb_2Si_3$ formed at the interface of $Nb/MoSi_2$ and increased with fabricating temperature. $MoSi_2$ composites which a hole drilling was not possible by the conventional machining process, enhanced the capacity of ED-drilling by adding $NbSi_2$ relative to that of SiC or $ZrO_2$ reinforcements.

[ $Nb/MoSi_2-ZrO_2$ ] laminate composites have been successfully fabricated by alternately stacking $MoSi_2-ZrO_2$ powder layer and Nb sheet, followed by hot pressing in a graphite mould. The fabricating parameters were selected as hot press temperatures. The instrumented Charpy impact test was carried out at the room temperature in order to investigate the relationship between impact properties and fabricating temperatures. The interfacial shear strength between $MoSi_2-ZrO_2$ and Nb, which is associated with the fabricating temperature and the growth of interfacial reaction layer, is also discussed. The plastic deformation of Nb sheet and the interfacial delamination were macroscopically observed. The $Nb/MoSi_2-ZrO_2$ laminate composites had the maximum impact value when fabricated at 1623K, accompanying the increase of fracture displacement and crack propagation energy. The interfacial shear strength of $Nb/MoSi_2-ZrO_2$ laminate composites increased with the growth of interfacial reaction layer, which resulted from the increase of fabricating temperature. there is an appropriate interfacial shear strength for the enhancement of impact value of $Nb/MoSi_2-ZrO_2$ laminate composites. A large increase of interfacial shear strength restrains the plastic deformation of Nb sheet.

In the present study, we examined the influence of prestrain on creep strength of Class M alloy(STS310S) and Class A(STS310J1TB) alloys containing precipitates. Prestrain was given by prior creep at a higher stress than the following creep stresses. Creep behaviour before and after stress change and creep rate of pre-strianed specimens were compared with that of virgin specimens. Pre-straining produced the strain region where the strain rate was lower than that of a virgin specimen both for STS310J1TB and STS310S steels. The reason for this phenomenon was ascribable to the viscous motion of dislocations, the interaction between dislocations and precipitates in a STS310J1TB steel, and the interaction of dislocations with sub-boundaries in a STS310S steel which has the higher dislocation density and smaller subgrain size resulted from pre-straining at higher stress.

The general purpose of this paper is Evaluation of material properties in spring steels by investigate correlation between ultrasonic attenuation and virker's hardness, charpy impact properties, microstructures. The three test speciments of the $490{\times}90 mm$ plates and 20 mm thick are used but differ in heat treatment, one is rolled plate, the second is quenched and then tempered, and the third is quenched. ultrasonic attenuation were obtained at fifteen locations on the plates. In order to investigate the correlation between hardness ( especially, HV ) and the attenuation, the virker's hardness and the microstructures were observed for three spring steels. also the charpy impact test were carried out at the room temperature in order to investigate the relationship between impact properties and the attenuation. The experimental results obtained from three different spring related to the heat treatment conditions and attenuation coefficient is increased with increasing the hardness(HV). Ultrasonic attenuation coefficients have shawn are ability to distinguish among spring steels.

선반건조 일정계획에 있어서 탑재 공정은 전체 생산일정 계획 중 선박 한 척에 대한 계획의 시발점이 되며, 병목현상 등을 유발하여 다른 일정에 가장 큰 영향을 주게 되는 공정이다. 최근 많은 조선소에서 하나의 Dock 내에서 두 착 이상의 배를 동시에 건조하는 tandem 방식을 택하고 있어 dock 내의 한정된 Crane 의 개수와 Crane의 Capacity, 공수 등의 자원, 그리고 작업환경에서 일어날 수 있는 여러 가지 변수들을 제대로 고려하지 못 했을 시에는 일정의 차질과 Dock의 회전율을 떨어트리게 한다. 본 논문에서는 가상공간에 하나의 Dock 를 만들어서 일정계획에서 작성한 Network를 사용하여 실제 작업하게 해서 그 Network가 현장에서의 최적한가를 점검하게 하고 현장에서 수정하는 작업을 줄이게 하는 것의 방법으로 simulation을 개발하였다.

In this paper, the stress and deformation characteristics of the high pressure hose that have the hose components such as rubber, braid and steel( sleeve and nipple) during the manufacturing process, and analyzed using the [mite element method The swaging process is modeled with a contact problem in identical conditions of real circumstances, and the properties of hose materials based on the experimental data are used in this analysis. Also, to understand the effect of the nipple protrusions on the deformation characteristics of a power steering hose among the steel materials shape of the existing model, and changed the steel materials shape partially, and compared with the existing model.

최근 들어 인터넷과 관련한 정보통신기술의 발전은 모든 산업환경을 변화시키고 있고, 조선 산업에서도 설계 생산성을 향상시키기 위해서 새로운 설계 패러다임을 선박설계 과정에 적용하고 있다. 현재 차도선을 설계하는 설계사무소의 경우 전문 설계인력이 부족함과 동시에 설계 과정은 동일한 작업이 반복적으로 수작업을 통해 이루어지고 있는 상태이다. 이러한 수작업의 반복은 설계 과장에서 에러를 발생시키고 각 설계 단계별로 발생하는 설계 데이터의 에러로 인해 설계생산성을 저하시키는 요인으로 작용될 수 있다. 따라서 본 시스템 개발은 초기설계 과정을 전산프로그램화 하여 초기설계 단계에서의 설계정보 데이터의 정확성을 높여 설계생산성을 향상시키고 또한 이 프로그램을 인터넷 기반으로 제공하여 분산된 환경에서도 다른 설계 전문가들이 함께 참여 할 수 있게 해 설계 정보를 동시에 공유하여 원격지에서도 설계자가 원하는 자료를 검색할 수 있도록 하는데 목적이 있다. 본 연구는 인터넷 기반을 통한 차도선의 초기설계 프로그램의 핵심을 이루는 인터넷 기반 구현 방법에 대해 소개하고 특히 인터넷 환경에서 차도선의 초기설계 프로그램을 통해 설계정보의 교환 및 공유를 원활하게 구현하는 시스템을 개발하는데 있다.

While upwelling regions account for only 0.1% of the ocean surface, they yield over 40% of world's fish catch. Thus it is vary important making upwelling region by various methods. This study was performed to find out basic hydrodynamic characteristics (function, stability..,) of artificial upwelling structures. The hydrodynamic characteristics of artificial upwelling structures can be summarized as follows: 1) The falling velocity of blocks was effected size($l_B$) of blocks than incident current velocity( $V_0$). 2) The falling horizontal distance was reduced as induce of stratification parameters and block' size. 3) Generation of artificial upwelling current was effected by size of structures and incident current. When stratification parameters was about 3.0 and relative height(hs/h) of structures was about $0.125{\sim}0.15$, stable artificial upwelling current was generated in the back-side of structures.

The tensile tests to identify the statistical tensile properties and the acoustic emission characteristics were conducted for STS304 stainless steel at $600^{\circ}C,\;700^{\circ}C$. From tensile tests performed by constant cross head speed controls with 1mm/min, rates at each elevated temperature, the scatters were observed in tensile strength, reduction of area, elongation and the acoustic emission parameters. The effect of temperature on the scatter of tensile behavior was larger at $700^{\circ}C$. The distributions of tensile properties was well followed in 3-parameter Weibull. The AE counts and energy of the $700^{\circ}C$ specimens were smaller than the $600^{\circ}C$.

In this research, a design guideline of current generating rotor and acceptable field rotor in offshore environment is proposed. To design rotor model, wind mill rotor design principles and turbine theories were applied based on a field rotor experimental data. To verify the compatibility of the rotor design method and to analyze the properties of design factors, 3 rotor models were designed and experimented in a circular water channel. Three rotor models were designed according to different blade numbers and blade shapes. With various flow velocities and rotor rpm, the rotor power and efficiency were measured and the properties of rotor were estimated. The results can be effectively applied to the design of current generation rotor.

The progressive die for U-bending production part is a very specific division. This study reveals the Sheet metal forming process with multi-forming die by Center Carrier type feeding system. Through the FEM simulation by DEFORM it was accepted to u-bending process as the first performance to design in strip process layout design. The next process of die development was studied according to sequence of die development.

The production part requiring multiple processes such as piecing, blanking and notching, are performed with a high production rates in progressive die. In order to prevent the dejects of process result, the optimum of strip process layout design, die design, die making, and tryout with inspection etc. are needed. According to these factors of die development process, they required theory and practice of metal working process and its phenomena, die structure, machining conditions for die making, die materials, heat treatment of die camponents, know-how and so on. In this study, we designed and analyzed die camponents also simulated the strip process layout of multiple stage drawing by DEFORM. Especially the result of tryout and its analysis become to the feature of this study.

By changing the excess air ratio which affects strongly to the combustion characteristics, the flame stability range in the metal fiber burner were found and the range of the blue flame male and radiant mode were distinguished by direct photography. The results in our experiments for the flame stability zone were from a=1.4($354 KW/m^2$) to a=2.06($240 KW/m^2$), and then the blue flame mode zone was form a=1.87($266 KW/m^2$) to a=2.06($240 KW/m^2$) and the radiant mode one was form a=1.4($354 KW/m^2$) to a =1.78($278 KW/m^2$). And the flame was not fired when a is less than the lean condition a=2.45($202 KW/m^2$).

In this paper, shock analysis was performed for coarse and fine mesh model using MSC/NASTRAN and ANSYS after substituting the foundation of deck mounted equipment of marine ship for mass-spring system. In order to determine input file in MSC/NASTRAN, dynamic response analysis was also performed using DDAM based on the calculation in the range of low frequency. It was confirmed that the coarse mesh model has the sufficient effective weight in a lower degree mode compared to fine mesh model.

In this paper, a statistical analysis of fatigue crack growth behavior under constant amplitude loads has been carried out. Fatigue crack growth tests were conducted on sixteen pre-cracked compact tension (CT) specimens of the pressure vessel (SPV50) steel in controlled identical load and environmental conditions. The assessment of the statistical distribution of fatigue crack growth experimental data obtained from SPV50 steel was studied and also the correlation of the parameter C and m in the Paris-Erdogan law was discussed. The probability distribution function of fatigue crack growth life seems to follow the 3-parameter Weibull. The fatigue crack growth rate seems to follow the 3-parameter Weibull and the log-normal distribution. The coefficient of variation (COV) of fatigue crack growth life was observed to decrease as the crack grows. A strong negative linear correlation exists between the coefficient C and the exponent m in Paris model. Fatigue crack growth rate data shows a normal distribution for both m and logC.

In this paper, various kinds of A-Frame are surveyed and classified according to their functional ability and sizes. Based on the study, a A-Frame that is suitable for ROV/AUV operation is designed. Basic theoretical structural requirements are applied and relevant Finite Element Analysis are carried out for the verification of the sound workability of the proposed A-Frame. Final configuration and the specification are proposed for the usage of ROV/AUV operation.

The lightness of components required in automobile and machinery industry is requiring high strength of components. In particular, manufacturing process and new materials development for solving the fatigue fracture problem attendant upon high strength of suspension of automobile are actively advanced. In this paper, the effect of compressive residual stress of spring steel(JISG SUP-9) by shot-peening on fatigue crack growth characteristics in high temperatures($100^{\circ}C,\;150^{\circ}C,\;180^{\circ}C$) was investigated with considering fracture mechanics. So, we can obtain followings. (1) Compressive residual stress is decreased in high temperature, that is, with increasing temperature. (2) The effect of compressive residual stress on fatigue crack growth behavior in high temperature is increased below ${\Delta}K=17{\sim}19MPa\sqrt{m}$. The fatigue crack growth rate is increased with increasing temperature. The fatigue life is decreased with increasing temperature. (3) The dependence of temperature and compressive residual stress on the parameters C and m in Paris' law formed the formulas such as equations (3),(4),(5),(6),(7),(8),(9),(10). (4) It was investigated by SEM that the constraint of compress residual stress for plastic zone of fatigue crack tip was decreased in high temperature as compared with room temperature.

Authors had developed the model for the fatigue life assessment of welded details considering residual stress and its relaxation. The model consists of three ingredients; a hot-spot stress approach, a residual stress relaxation, and an equivalent stress. The equivalent stress is induced by stress ranges and the ratios between the applied mean stresses and the ultimate stress of material. Once being tuned with two specific fatigue tests by using load carrying cruciform joint, this model can be applied to many kinds of welded details which structural stress concentration factors are different from each other. This paper reports the application of the proposed model for various welded details including cover plate, longitudinal stiffener, gusset and side attachment. From the investigation of predicted results by using the proposed model it was shown that the ambiguous fatigue characteristics of the various details influenced widely by the welding residual stress are clarified, and also the model could be applied to assess fatigue life of general welded structures.

Polyethylene pressure pipe has been used with a gas pipe material because of workability and stability etc.. Researches on characteristics of polyethylene pressure pipe are carried out, but there are rare. In this study, the tensile test was performed on polyethylene pipe. From the tensile test, AE signals were detected and estimated in real time. Also, the time-frequency analysis of AE signals was analyzed. From test results, PE pipes were displayed typical stress-strain curves oj semi-crystalline polymer. As result analyzed AE signals, could divide stress-strain curves could be divided into four stages. In the elastic region, signals were not detected. Low amplitude distributions of 30-35dB appeared after yielding, and high amplitude distributions of 30-60dB appeared with increased extension. From the time-frequency analysis of AE signals, the frequency band of 100kHz appeared mainly. Also, the frequency band of 300kHz appeared before the necking phenomenon spreads into the whole region, and the frequency band of 500kHz appeared on extension earlier.

Fracture behaviors of pipes with local wall thinning are very important for the integrity of nuclear power plant. However, effects of local wall thinning on strength and fracture behaviors of piping system were not well studied. Acoustic emission(AE) has been widely used in various fields because of its extreme sensitivity, dynamic detection ability and location of growing defects. In this study, we investigated failure modes of locally wall thinned pipes and AE signals by bending test. From test results, we could be divided four types of failure modes of ovalization, crack initiation after ovalization, local buckling and crack initiation after local buckling. And fracture behaviors such as elastic region, yielding range, plastic deformation range and crack progress could be evaluated by AE counts, accumulative counts and time-frequency analysis during bending test. It is expected to be basic data that can protect a risk according to local wall thinning of pipes, as a real time test of AE.

In this paper, the plastic zone size ahead of the crack tip of DENT specimen and the crack growth length under cyclic loading were measured by ESPI system. These results of the plastic zone size measured by ESPI system were compared with the plastic zone size proposed by Irwin. The results of tile crack growth length measured by it were also compared with them measured by the image analysis system. It is confirmed that it is possible to measure the plastic zone and crack growth length.

Tubular joints having a large diameter in the offshore structure are reinforced using internal ring stiffener in order to increase the load carrying capacity. In this study, the static strengths of internally ring-stiffened tubular T-joints subjected to compressive brace loading are assessed. Nonlinear finite element analyses are used to compute the behavior of unstiffened and ring-stiffened T-joints. From the numerical results, internal ring stiffener is found to efficient in improving the ultimate capacity, and reinforcement effect are calculated. The influence of geometric parameters for members and ring is evaluated. Based on the FE results, regression analysis is performed considering practical sizes of ring stiffener, finally strength estimation formulae for ring-stiffened T-joints are proposed.

In this paper, the effect of the crack growth length on the plastic zone size at the crack tip and the crack growth lives of the DENT specimen under constant amplitude cyclic loading were studied. The plastic zone size was calculated by nonlinear static method in commercial finite element analysis program, MSC/NASTRAN and the crack growth lives were also calculated by using compliance function considering geometric shape in MSC/FATIGUE. The calculated plastic zone size increased proportional to the crack length. And comparison of calculated plastic zone size and crack growth lives with the experimental results shows a good agreement.

Metal matrix composites had generated a lot of interest in recent times because of significant in specific properties. It was also highlighted as the materials of frontier industry because strength, heat-resistant, corrosion-resistant, wear-resistant were superiored. In this study the strength properties of $Al_{18}B_4O_{33}/AC4CH$ were represented mixing the binder of $Al_2O_3$ and $TiO_2$. It was also fabricated by squeeze casting. $Al_{18}B_4O_{33}/AC4CH$ was fabricated at the melt temperature of $760^{\circ}C$ the perform temperature of $700^{\circ}C$ and mold temperature of $200^{\circ}C$ under the pressure of 83.4MPa and observed SEM. Fatigue crack growth rate tests on compact tension specimen(half-size) of thickness 12.5mm were conducted by using sinusoidal waveform. Compact tension specimens(half-size) were used and fatigue crack growth rate da/dN and stress intensity factor range ${\Delta}K$ were analyzed concerning to the R value of 0.1 and 0.05. In order to find out the value of ${\Delta}K$, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. As the results of this study, Fatigue crack growth rate increased with in creasing the load ratio, Consequently, At equivalent stress intensity factors, the fatigue crack growth rates in MMC were faster than those of AC4CH alloy. then the fatigue life and the fatigue crack growth rate was investigated using scanning election microscopy(SEM)

Low-tension cables have been increasingly used in recent years due to deep-sea developments and the advent of synthetic cables. In the case of low-tension cables, large displacements may happen due to relatively small restoring forces of tension and thus the effects of fluid and geometric non-linearities become predominant. In this study, three-dimensional (3-D) dynamic behavior of a towed low-tension cable with non-uniform characteristics is numerically analyzed by considering fluid and geometric non-linearities and bending stiffness. A Fortran program is developed by employing a finite difference method. In the algorithm, an implicit time integration and Newton-Raphson iteration are adopted. For the calculation of huge size of matrices, block tri-diagonal matrix method is applied, which is much faster than the well-known Gauss-Jordan method in two point boundary value problems. Some case studies are carried out and the results of numerical simulations are compared with a in-house program of WHOI Cable with good agreements.

In this study, CT specimens were prepared from spring steel(SUP9) processed shot peening which was room temperature, high temperature experiment. And ire got the following characteristics from fatigue crack growth test carried out in the environment of room, and high temperature at $25^{\circ}C,\;100^{\circ}C,\;150^{\circ}C$ and $180^{\circ}C$ in the range of stress ratio of 0.3 by means of opening mode displacement. The threshold stress intensity factor range ${\Delta}Kth$ in the early stage of fatigue crack growth (Region I) and stress intensity (actor range ${\Delta}K$ in the stable of fatigue crack growth (Region II) was decreased in proportion to descend temperature. It assumed that the fatigue resistance characteristics and fracture strength at high temperature is considerable higher than that of room temperature in the early stage and stable of fatigue crack growth region.

Fourier transform has been one of the most common tools to study the frequency characteristics of signals. With the Fourier transform alone, it is difficult to tell whether signal's frequency contents evolve in time or not. Except for a few special cases, the frequency contents of most signals encountered in the real world change with time. Time-frequency methods are developed recently to overcome the drawbacks of Fourier transform, which can represent the information of signals in time and frequency at the same time. In this study, heat damage process of a carbon fiber reinforced plastic(CFRP) and glass fiber reinforced plastic(GFRP) under monotonic tensile loading was characterized by acoustic emission. Different kinds of specimens were used to determine the characteristics of Strength and AE signals. Time-frequency analysis methods were employed for the analysis of fracture mechanism in CFRP such as matrix cracking, debonding and fiber fracture.

For the development of the practical design and analysis scheme of a bridge connecting to the typical VLFS, relevant design criteria and theory and techniques are studied and numerical analysis for the verification of the structural safety of the bridge are carried out. For the design of a typical steel bridge, characteristics of proper type bridge are reviewed and the requirements fur the bridge of this kind are studied as well as the environmental loads. By using the design spiral technique, several alternatives are investigated and an efficient type of a bridge is initially designed. Structural idealization is performed to make overall structural analysis first, and the structural behaviors of the proposed bridge in the given loading condition are evaluated. Through this study a bridge is finally proposed and it is found that this one works well for the connecting function of the bridge.

It has made a special study of bending behavior of F.R.P sandwich beams with bonded 2nd-reinforced plies. Specimens were made of Chopped Mat 300-450, Roving Clothes 570 and the mixture weight ratio of Resin versus hardener was 55:45 for bending tests. it was fabricated by hand lay-up method, hardened for 24 hours in nature, cut specimens according to ASTM standard C393-94 Knowing exact behavior of bonded area's stress and strain depends upon various bonded F.R.P length on which covered lap joint. We also considered shear stress in adhered area and have done computational estimation by ANSYS as well. This study reveals that the length of plies covered lap joint are longer, Failure stresses are remarkably larger.

The motion of a floating OWC chamber in waves is studied taking account of fluctuating.air pressure in the air chamber. An atmospheric pressure drop occurs across the upper opening of the chamber which causes not only hydrodynamic but also pneumatic added mass and damping forces to the floating chamber. A velocity potential in the water due to the free surface oscillating pressure patch is added to the conventional radiation-diffraction potential problem. The potential problem inside the chamber is formulated by making use of the Green integral equation associated with the Rankine Green function while the outer problem with the Kelvin Green function. The two integral equations are solved simultaneously by making use of a matching boundary condition at the lower opening of the chamber to the outer water region. The chamber motion in the frequency domain is calculated for various values of parameters related to the atmospheric pressure drop. The present methods can also be used for the analysis of air-cushion vehicle motion as well as for the design oj a floating owe wave energy absorber.

본 연구에서는 반잠수식 Rig의 형상에 따른 최적 형상을 검토하기 위하여 최근 건조되고 있는 4-Column과 2-Lowhull을 가진 사각 Column에 원통형 Column을 혼합한 혼합형 과 4각 Column형을 공시모형으로 택하여 규칙파중 두 구조물에 작용하는 유체력과 유체력에 의한 운동 응답을 계산하고, 4각 Column을 가지는 구조물의 길이, 폭, 홀수를 변화시킨 Series 에 따른 유체 역학적 특성과 동요 진폭의 관계를 검토하였다. 수치계산은 3차원 특이점 분포법을 이용하여 정상상태에 대하여 실행하였다. 구조물의 형상과 역학적인 간섭의 영향을 이용, 보다 성능이 우수한 형상을 얻을 수 있음을 확인하였다.

Mooring is the operation of securing a ship to a wharf or quay by means of rapes or chains. A. moored ship need not necessarily be truly stationary. It may be free to rise and fall with the tick or the loading and unloading of cargo or to oscillate in response to the action of the environmental forces. In this respect a moored ship is restricted to a limited amount of movement within well-defined bounds. This study is intended to analyze the tension of mooring lines by a FEM program, as the current velocities and working directions are varied. The motion of a berthed ship is studied concerning with the wave periods and the direction. Also the behavior of the modeled vessel are investigated for a berthed condition.

We developed a small, remote controlled observation ship that can reduce the cost of gathering data for marine and coastal environments. The control system is composed of three microprocessors, one is for overall mission control, another for control of propulsion motors, and the other for sensor operation. For communication system, we adopt direct and indirect methods based on the wireless modem of commercial cellular telephone. The former is a direct communication between the modems of the ship and the server, and the latter is an indirect communication via internet between the ship and the server. The performance of the ship is demonstrated with the results produced by sets of experiments.

In this study, we show the numerical and the experimental results for fluid motions inside a rectangular container subjected to a background rotation added by a rotational oscillation. In the numerical computation, we used a parallel computer system of PC-cluster type. Attention is given to dependence of the flow patterns on the parameter change. It shows that the flow becomes in a periodic state at low Reynolds numbers and undergoes a transition to a chaotic motion at high Reynolds numbers. It also shows that the fluid motion tends to be depth-independent at ${\epsilon}$ up to 0.3 for Re lower than 5235.

In this paper, flow in the wake region of a butterfly valve is studied numerically and experimentally. The disk angle of the valve is fixed as $30^{\circ}$ and the free stream velocity as 0.13m/s in the experiment. Numerical analysis is performed in similitude of the experiment. The standard LES model is used to represent the turbulence effect in the commercial code Fluent 5.5. It is shown that the numerical result is similar to the experimental result for the wake flow of a butterfly-type valve.

현재 미 해군에서 개발 중인 DD21은, 미 해군의 해상 전투력 구조의 핵심인 이지스급 함정을 제외한 DD-963급 구축함과 FFG-7급 프리깃 함의 교체함으로서, 연안전에 대한 새로운 특수 임무에 적응할 수 있게 많은 학자들에 의해 연구되고 있는 차세대 구축함이다. 즉, DD21은 기존 이지스 함정에 부가하여 대지전(Land Attack)과 대기뢰전을 포함한 다목적의 기능을 발휘하면서 전투원의 스마트(Smart), 배치와 장비와 기구의 자동화와 기계화를 통한 함정과 함체의 스텔스(Stealth)화로 유지비와 초기 투자비를 최소화시킨 함정이다.

By using the infinite dimensional optimization[Jang and Kinoshita(2000)]. which is based on the Hilbert space theory, optimal marine propellers are studied. The mathematical uniqueness for the optimized propeller is shown in this study. As a numerical example, the MAU type propeller is considered and used as the initial guess for the optimization method. The numerical results for an optimal marine propeller is illustrated for the pitch distribution.

최근 우리나라 연안어업은 한일, 한중어업협정, WTO 가입 등으로 주변 환경이 급격하게 변화되는 한편, 연근해 어자원의 감소와 근해어업과의 경쟁조업 등으로 인해 경영수지가 극도로 악화되고 있다. 이로 인해 연안어민들의 최소 생계기반 마저 위협받고 있는 실정이다. 이에 본 연구는 연안어업의 수익향상과 자원관리 측면에서 경제성 연안 어선의 선형개발 방안을 검토하였다. 이를 위해 새로운 어선어업 환경에서 요구하는 자원관리, 채산성보장 등의 경제 사회적 요건을 기술적 요소로 변환하여 다목적어선의 개념을 설정하고 관련 기초자료를 마련하였다. 특히, 연안어업을 동해, 서해, 남해, 서남해 등으로 나누어 허가업종의 실태와 어민 요구사항이 서로 다른 점을 감안하여 다목적화 가능 업종을 선정하고, 선형개발 방안을 도출, 정리하였다.

According to Ocean Korea 21, a basic plan established by the Ministry of Maritime Affairs and Fisheries (MOMAF) of Korea in May 2000, Korea Research Institute of Ships and Ocean Engineering (KRISO) proposed a program for the development of a deep-sea unmanned underwater vehicle (UUV) to explore deep sea for scientific purpose. KRISO has launched a project in May 2001 under the support of MOMAF. The deep-sea unmanned underwater vehicle will be applied to scientific researches in deep-sea as well as in shallow water. For operation of underwater vehicles in shallow water near the Korean Peninsula, a special design is required because of strong tidal current. In addition, MOMAF requires the vehicle to be designed for the purpose of long range survey, a long-term observation, and precise works in a specific area. Thus, KRISO has planned to design the system with the functional combination of both ROV and AUV. This paper presents the design of the deep-sea unmanned underwater vehicle.

Resistance performance of small size fishing vessel is experimentally investigated to find out the effect of fore-body shape and trim for the better hull form development. The tests are performed for four different cases in the high speed circulating water channel(CWC). Wave patterns are observed together to investigate the relation between the resistance performance and the wave characteristics.

Numerical model introduced in this study combines wave refraction-diffraction, breaking, bottom friction, lateral mixing, and critical shear stress and three sub-models for simulating waves, currents, and bottom change were briefly discussed. Simulations of beach processes and harbor sedimentation were also described at the coast neighboring Bangpo Harbor, Anmyundo, Chungnam, where the area has suffered from accumulation of drifting sand in a small fishing harbor with a wide tidal range. We also made model test for the case of a narrow tidal range at Nakdong river's estuary area to understand the effect of water level variation on the littoral drift. Simulations are conducted in terms of incident wave direction and tidal level. Characteristics of wave transformation, nearshore current, sediment transport, and bottom change are shown and analyzed. We found from the simulation that the tidal level impact to the sediment transport is very important and we should apply the numerical model with different water level to analyze sediment transport mechanism correctly. Although the model study gave reasonable description of beach processes and harbor sedimentation mechanism, it is necessary to collect lots of field observation data, including waves, tides and bottom materials, etc. for better prediction.

The wave profiles of directional breaking waves are investigated experimentally in a directional wave basin. The directional breaking waves are generated by component wave focusing both in direction and frequency based on constant wave steepness and constant wave amplitude spectrum models. the profile parameters of wave crest steepness and asymmetry are adapted to analyze the evolution of breaking ware characteristics in a view of focusing efficiency. The generated breaking waves are classified into the incipient, single and multi breaking waves.

This paper presents the results of wave profile detection from video image using Mexican hat function. The Mexican hat function has been extensively used in the filed of signal processing to detect discontinuity in the images. The analysis was done on the numerical image and video images of waves which were taken in the circulating water channel. The results show that Mexican hat function is an excellent tool in the wave profile detection.

Results of a numerical simulation of a flowing of the underwater vehicles hull with the pump-jet nozzle are presented. It was calculate velocity distributions and coefficients of the lift force and the longitudinal moment of the hull with the pump-jet nozzle and isolated hull for some values of angle of attack. It was shown that the area of tile influence of the nozzle on the velocities distribution of the hull and character of changing of coefficients of the lift force and the longitudinal moment and their derivatives depending on angle of attack.

Nowadays, many components used in machinery industry is required lightness and high strength. Therefore, the effects of compressive residual stress by shot-peening which is method to improve fatigue lift of spring steel (JISG SUP-9), which used in suspension of automobile, on fatigue crack growth characteristics was investigated with considering fracture mechanics. So, we can obtain followings 1. The fatigue crack growth rate on stage II is conspicuous with the size of compressive residual stress and is dependent on Paris equation. 2. Although the maximum compressive residual stress is deeply and widely formed from surface, fatigue life does not improve than when maximum compressive residual stress is formed in surface. 3. The threshold stress intensity factor range is increased with increasing compressive residual stress. 4. In fracture surface of fatigue crack growth it is investigated that compressive residual stress remarkably retards fatigue crack growth.