Some of factors affecting photo-conversion efficiency of dye sensitized solar cells (DSCs) are discussed in terms of $TiO_2$ electrodes. The first topic is on the surface modification of $TiO_2$ nano-particles, which is associated with electron traps on the surface of $TiO_2$ nano-particles. The surface is modified with dye molecules under pressurized $CO_2$ atmosphere to increase the surface coverage of $TiO_2$ nano-particles with dye molecules. This increases Jsc because of an increase in the amount of dye molecules and a decrease in the amount of trapping sites on $TiO_2$ nano-particles. In addition, the decrease in the amount of trap sites increases Voc because decreases in Voc are brought about by the recombination of $I_2$ molecules with electrons trapped on the $TiO_2$ surfaces. Selective staining for tandem cells is proposed. The second topic is on the contact between a $SnO_2$/F transparent conductive layer (TCL) and nano-particles. Polishing the TCL surfaces with silica nano-particles increases the contact, resulting in Jsc increases. The third topic is the fabrication of ion-paths in $TiO_2$ layers. Electro-spray coating of $TiO_2$ nano-particles onto TCL is shown to be effective for fabricating ion-paths in $TiO_2$ layers, which increases Jsc.

In the single-phase switched reluctance motor (SRM) drive, the required DC source is generally supplied by the circuit consisting of bridge rectifier and large filter capacitor connected with DC line terminal. Due to the large capacity of the capacitor, the charged time of capacitor is very short from the AC source. Lead to the bridge rectifiers draws pulsating current from the AC source side, which results in reduction of power factor and low system efficiency. Therefore a novel single-phase SRM drive system is presented in this paper, which includes drive circuit realizing reduction of torque ripple and improvement of power factor with a novel switching topology. The proposed drive circuit consists of one switching part and diode, which can separate the output of AC/DC rectifier from the large capacitor and supply power to SRM alternately, in order to realize the torque ripple reduction and power factor improvement through the switching scheme. In addition, the validity of the proposed method is tested by some simulations and experiments.

This paper presents a scheme on the characteristics of induction motor under the combination of linear & non-linear loads at the three phase 4-wire power distribution system. Under the combination operation of single & three phase load, voltage unbalance will be generated and current unbalance will be more severe by the dropped voltage quality. All power electronic converters used in different types of electronic systems can increase harmonic disturbances by injecting harmonic currents directly into the feeder grid of three phase 4-wire. Harmonic current may cause torque to decrease. Motors may also overheat or become noisy and torque oscillation in the rotor can lead to mechanical resonance and vibration.

This paper formulates the principle of the magnetic actuator break system (MASS) for emergency situation driving a car. When the exciting break system of a car is broken, MASS will be able to stop the car by the electric system. MASS controls the rotating wheel to slow down gradually while holding and laying the wheel down several ten times per second. We present the magnetic field and dynamic behavior analyses for the magnetic actuator break system using finite element method (FEM) associated with parameter, for calculating the displacement of the moving parts and the supplying current.

본 논문은 단상 1MVA 22.9kV/220V 케이블 변압기의 설계, 제작 및 시험 결과를 서술한다. 케이블 변압기는 유입변압기의 폭발위험성과 환경오염 가능성이 없으므로, 인구밀집지역, 지하장소등 설치장소의 제한이 없는 장점이 있다. 제작된 케이블 변압기는 22.9kV급의 XLPE 케이블 전선을 사용하여 1차 권선을 제작하였으며, 2차측 권선은 내 단락시 특성이 우수한 몰드 권선 형태로 제작하였다. 사용된 XLPE 케이블은 도체-내부반도전층-XLPE-외부반도전층으로 구성되어 있으며, 외부반도전층은 접지된 구조이다. 철심은 단상 3각 구조로써 방향성 규소강판을 사용하였으며, 냉각방식은 공기 자연냉각방식이다. 제작된 변압기의 신뢰성을 확보하기 위하여, 특성시험과 절연시험을 실시하였다.

최근 중 저압용 진공 차단기의 구동 메커니즘으로 영구자석형 조작기(PMA)가 널리 사용되고 있다. 이는 모터 스프링이나 유압 및 공압식 등과 같은 기계식 메커니즘에 비해 성능과 신뢰성에서 우수함을 인정받고 있다. 그러나 기존 영구자석형 조작기에서는 가동자와 영구 자석 사이의 큰 마찰력으로 인한 에너지 손실과 차단부와의 연결 로드에서의 기계적 고장 및 파손이 유발될 수 있다. 본 논문에서는 가동자의 로드에 베어링 타입의 부싱을 장착한 모델을 제안함으로써 이 문제를 해결하고자 한다. 부싱을 이용하여 영구 자석과 가동자 사이의 공극을 확보함으로써 마찰을 감소시키고 기계적 안정성 및 동작 특성 향상을 기대할 수 있다. 유한요소법(FEM)과 시간차분법(TDM)을 이용하여 제안된 모델의 동작 특성을 해석하였고, 이를 기존 모델의 특성과 비교하여 그 우수성을 검증한다.

변압기에서 단락기계력에 대한 계산 분야는 수직력에 의한 Beam Bending, Tillting, 절연물 압축력과 수평력에 의한 Hoop, Compression 등이 있다. 본 논문은 전력용변압기 내부의 자계를 자기영상법을 이용하여 구하고 계산된 자계를 이용하여 단락 기계력을 구하는 방법을 제안하고자 한다. 또한 기존 FEM과 자기영상법과의 계산결과를 비교하였다.

This paper deals with electormagnetic analysis of reluctance type machines with permanent magnet/electromagn et. First, we calculated flux density of relucta nce type machines with permanent magnet/electromagnet according to position. Second, analyzed normal force and horizontal force from flux density of machine according to position. Also, analysis result compares with data that is derived through a finite element analysis (FEA), and proved validity.

A grid-connected distributed generation system which consists of engine generator, dc link with multiple energy sources and inverter is proposed. All six of the stator leads of the generator, which is a surface mount permanent magnet machine, are brought out to the terminal of the generator. Three leads are connected to the inverter and the others are connected to the utility grid. In this proposed system the power from the engine-generator and the power from dc link can be controlled simultaneously by only one three-phase power converter. A control algorithm for the system is developed and verified by experiment results.

The direct instantaneous torque control (DITC) method is presented in this paper, which enables torque to be generated during all region and instantaneous torque control to be possible. The hysteresis control mode with the compared value between given torque and instantaneous output torque as input is applied in respect region. The output torque function, that is instantaneous output torque with the variation of current and position of rotor, is achieved by experiment. In this control mode the torque subsection function and current control are not needed. The turn on angle with variation of load torque and speed is only selected and turn off angle can be neglected. The validity of method is tested by simulation and experiment.

Miniature BLDC is widely used in industrial applications and especially medical appliances because of there character that high driving efficiency and high torque characteristic. However torque ripple of a high speed miniature BLDC is serous in switching period cue to the very electrical time constant. This paper present instant voltage and current control for torque ripple reduction of a high speed miniature BLDC. Computer simulation and experiment test for 40,000 rpm miniature BLDC show the verification of the proposed control method.

This paper proposes high speed SRM drive system for blower with a new 4-level inverter and precise excitation position generator. For the high speed blower, a proper inverter and control method are proposed and the output characteristics are analyzed. In order to get a fast build-up and demagnetization of excitation a current, 4-level inverter system is proposed. The proposed 4-level inverter has additional charge capacitor, power switch and diode in the conventional asymmetric converter. The charged high voltage is supplied to the phase winding for fast current build-up, and demagnetization current is charged to additional capacitor of 4-level inverter. In addition, a precise excitation position generator can reduce turn-on and turn-off angle error according to sampling period of digital control system. The proposed high speed SRM drive system is verified by computer simulation and experimental result.

This paper proposes a DITC(Direct Instantaneous Torque Control of SRM (Switched Reluctance Motor) using a novel 4-level converter for smooth torque control and high efficiency. DITC of SRM is very useful for smooth torque control, but the driving efficiency is low due to advanced current that does not produce torque. For the high efficiency control of SRM, fast excitation and demagnetization of phase current are required. A novel 4-level converter and a new control scheme are present to improve the driving efficiency. The proposed DITC of SRM using 4-level converter is verified by computer simulation.

전자빔 발생장치를 이용한 마이크로파 출력을 증대시키기 위하여 주기구조를 갖는 지파도파관을 이용하였다. 이것은 공명적인 현상에 의하여 마이크로파 발진을 일으켜 출력 증대를 가져온다. 중심 축상의 고주파 전계 분포와 전자 빔 밀도의 상호작용에 의한 에너지 증대가 이루어지면서 이에 따라 대 출력이 얻어진다. 본 연구는 지금까지 연구되어 왔던 것보다 더 많은 출력을 얻기 위하여 지파도파관을 이용한 실험을 하여 연구하였다.

This paper shows the design of a levitation magnet for an OLED system which has a large air gap. Evolution strategy was adopted for the optimization of the magnet system. During the optimization process, interpolation of levitation force was used to reduce the computation time which was needed to calculate the levitation force. Object function for optimization was total weight of the magnet system.

This paper deals with a noise and vibration of brushless dc (BLDC) motors due to the asymmetrical overhang of permanent magnet. The asymmetrical overhang of permanent magnet is generating z-axis thrust which is lead to eccentric force and vibration of BLDC motor. The z-axis thrust considering asymmetrical overhang effect of permanent magnet is analyzed by using 3-D FEM and the result is compared to experimentation.

This paper deals with skew and overhang effects of Permanent Magnet in PMLSM. The detent force and thrust characteristics considering skew and overhang effects of permanent magnet are analyzed by 3D FEM and the results are compared to experimental values

The detent force by end-effect has a bad influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect the auxiliary teeth is installed at the end part of mover and it is optimized by using neural network.

This paper proposes a new stator pole shape having non-uniform air-gap in order to minimize the undesirable torque ripple of switched reluctance motor(SRM). Through numerical analysis using finite element method(FEM) and optimization, the proposed pole-shape-optimized stator is proven to give reduced torque ripple.

In this paper, the notch of teeth and skew of permanent magnet are used to reduce the detent force caused by slot-teeth structure. Also, the shape of permanent magnet is optimized to reduce the detent forceowing to flux hannonics components of permanent magnet. As a result, thrust is decrease about 2[%]. But, the distortion ratio of thrust is decreased from 1.04[%] to 0.75[%]. And, the ripple ratio of thrust is decreased from 2.6[%] to 1.65[%].

In this paper, a synchronous permanent magnet planar motor (SPMPM) with new permanent magnet array is proposed and the magnetic field distribution is obtained analytically by using magnetic scalar potential. Compared to those of Asakawa, Chitayat and experimental data, the superiority and feasibility of the novel magnet array are verified. The characteristics of the synchronous permanent magnet planar motor with this novel magnet array such as inductance, back-EMF, and force are calculated by analytical method.

In this paper, a synchronous permanent magnet planar motor (SPMPM) with Halbach array is proposed for its high energy density. The magnetization and flux density distribution are obtainedby magnet scalar potential the characteristics such as inductance, back-EMF and thrust are evaluated. It can be concluded that the analysis of SPMPM with Halbach magnet array is credible and feasible.

For the reliability assessment of solenoid actuator, firstly, we analyzed the cause of major failures and the effect of each failure modes through FMEA and FTA, and decided the main test items through 2-stage QFD. And then, as a measure of life of solenoid actuator, TypeII censored five data were collected from and operation test which was performed as the life test of solenoid actuator. In this paper, we present the reliability parameters of solenoid actuator like shape parameter, scale parameter, etc., which they are produced by MINITAB analysis and marking of Weibull probability paper using the measure of life, and also present the 6 kinds of detailed failure mode analysis.

전기강판으로 제작된 전기기기의 보다 정확한 수치적인 해석을 위해서는 회전자계(Rotating m-agnetic flux)에 따른 전기강판의 정확한 자계특성 측정이 필요하다. 본 논문에서는 개발된 2방향 자계인가 형 Single sheet tester를 이용하여 회전자계에 따른 전기강판의 자계특성을 측정하였다. 실험을 통하여 등방성 시료와 이방성 시료에 대하여 각각 회전자계 및 교번, 회전자계의 혼합형 자계를 인가하여 1.6[T]와 1.2[T]까지 측정할 수 있었으며, 일반적인 철손(Alternating Iron Loss)외에 회전자계 인가 시에 B와 H의 위상차이에 의해 발생하는 회전자계 손실을 측정하였다.

단 1차형 영구자석 선형 동기 전통기(PMLSM)는 디텐트력과 단부력에 의한 큰 토크 리플을 갖는 문제점이 있다. 본 논문에서는 영구자석 선형 통기 전동기의 디텐트력을 줄이기 위해 영구자석의 극수와 전기자의 슬롯수의 비를 변경한 새로운 구조의 단 1차형 영구자석 선형 동기 전동기를 제안하였으며, 단부력을 줄이기 위하며 고정자의 길이 조정 및 챔퍼링을 통하여 영구자석 선형 동기 전동기를 설계하였다.

Cogging torque is often a principal source of vibration, noise and difficulty of control in permanent-magnet brushless DC motors. Cogging torque can be minimized by sinusoidal air-gap flux density waveform because it is produced by the interaction of the rotor magnetic flux and angular variation in the stator magnetic reluctance. Therefore, this paper will present a design method of magnetization system of bonded isotropic neodynium-iron-boron(Nd-Fe-B) magnets in ring type with sinusoidal air-gap flux density distribution and low manufacturing cost. An analytical technique of magnetization makes use of two-dimensional finite element method(2D FEM) and Preisach model that expresses the hysteresis phenomenon of magnetic materials in order for accurate calculation.

In this paper, single phase induction motor achieved improvement in efficiency by adapting the condition of Balanced operation and Quasi-balanced operation. Also, the process of efficiency improvement to find the optimum point of secondary resistance and running capacitor for working single phase induction motor is performed in order to attain the conclusion to put out the maximum efficiency at the rated operation point with meeting the starting torque.

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications. This paper proposes efficiency optimization control of IPMSM drive using AFLC-FNN(Adaptive Fuzzy Learning Control Fuzzy Neural Network)controller. In order to maximize the efficiency in such applications, this paper proposes the optimal control method of the armature current. The optimal current can be decided according to the operating speed and the load conditions. This paper proposes speed control of IPMSM using AFLC-FNN and estimation of speed using ANN controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled AFLC-FNN controller, the operating characteristics controlled by efficiency optimization control are examined in detail.

This paper shows the characteristic analysis of single-phase LSPM(Line Start Permanent Magnet) synchronous motor considering overhang structure. To obtain the dynamic and steady performance of the motor, the D-Q equivalent circuit is used and the circuit parameters are extracted by 3D FEM. The performance of the model with overhang is compared with conventional model without overhang on the condition that both models have the same volume of the permanent magnet.

This paper investigates the adaptive control of a fuzzy logic based speed and flux controller for a vector controlled induction motor drive. A model reference adaptive scheme is proposed in which the adaptation mechanism is executed by fuzzy logic based on the error and change of error measured between the motor speed and output of a reference model. The control performance of the adaptive fuzzy controller is evaluated by simulation for various operating conditions. The validity of the proposed adaptive fuzzy controller is confirmed by performance results for induction motor drive system

The paper is proposed maximum torque control of SynRM drive using adaptive learning mechanism-fuzzy neural network(ALM-FNN) controller and artificial neural network(ANN). The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_d$ for maximum torque operation is derived. The proposed control algorithm is applied to SynRM drive system controlled ALM-FNN and ANN controller, the operating characteristics controlled by maximum torque control are examined in detail. Also, this paper is proposed the analysis results to verify the effectiveness of the ALM-FNN and ANN controller.

The structure of interior permanent magnet type brushless DC motor (IPM type BLDC motor) has high saliency ratios that produce additional reluctance torque. But this structure has a significant cogging torque that may cause acoustic noise and vibration. In this paper describes an optimization of flux barrier in order to reduce cogging torque and torque ripple in IPM type BLDC motor using the Taguchi methods. The optimal design consider- ed noises such as manufacturing tolerances of permanent magnet size. So, optimal design ensures that torque performance is insensitive to noise.

This paper presents the experiment and the characteristics analysis of an electromagnetic pump using linear induction motor(LIM). The characteristics of LIM pump are analyzed solving the hydrodynamic equation at constant magnetic flux. The molten zinc is used in the experiment and the experimental results are compared with the analysis.

본 연구에서는 전력계통에서 발생되는 고장 전류에 의해서 변압기의 1차측 코일에 유도되는 전자력의 크기를 유한요소 전자계해석 프로그램(FLUX2D)을 이용하여 해석하였다. 50kVA, 13200/230(V) 단상 변압기의 권선간 전자력계산을 축대칭FEM을 이용하여 각 방향의 전자력을 분석하였다. 누설자속분포, 전류유입시 권선상호간에 작용하는 힘의 변화와 힘의 분포, 변압기 내부권선의 정상시와 고장전류시의 전자계비교를 전자계 해석을 통하여 변압기에 미치는 영향을 해석하였다. 변압기에 대전류가 유입되는 경우의 전자력 분석결과는 변압기의 절연설계 및 단락기계력에 대한 프레임 구조 설계를 위한 자료로 활용된다.

대용량 BLDC 모터의 진동 및 소음의 원인은 영구자석과 슬롯 개구부 형상에 의한 코깅토크와 전류 파형에 의하여 발생하게 된다. 특히 대용량 BLDC의 경우 코깅토크에 의한 진동 및 소음의 영향이 상대적으로 큰 값을 가지게 된다. 따라서 코깅토크 발생원인 중 하나인 영구자석의 형상에 RSM(Response Surface Method) 최적화 이론을 적용하여 코깅토크 저감을 연구하였다. FEM과 RSM을 결합하여 영구자석의 형상을 최적화한 결과 코깅토크의 ripple이 25%이상 감소되었다.

This paper proposes a design method by varying rotor pole shape to reduce cogging torque, torque ripple and harmonics of back emf in Spoke type brushless DC(BLDC) motor. In the process of design and analysis, Response surface method(RSM) and finite-element method(FEM) are employed to get the rotor geometry and verify the results of new pole shape.

소형화 되어 가는 전기기기에 따른 소형 모터가 요구되고 있다. 소형 모터 중 높은 정지 토크 및 높은 효율 등의 장점을 가진 소형 로터리 초음파 모터는 여러 목적에 쓰이고 있다. 하지만 주로 경험적인 방법 또는 상용 해석툴이 소형 로터리 초음파 모터의 해석에 주로 사용되었다. 따라서 소형 로터리 초음파 모터의 체계적인 해석 방법이 필요하다. 본 논문에서는 우선 소형 로터리 초음파 모터의 동작 원리를 통해 진행파의 존재를 확인하였고, 유한요소법 해석법을 통해 과도 및 정상 상태의 소형 로터리 초음파모터를 설계하고 해석하였다. 이 해석결과를 이용하여 소형 로터리 초음파 모터의 동작 특성 또한 해석하였다.

This paper is intended to research the speed response of switched reluctance motor (SRM) using sliding mode control method when load is changing. The simulation compare only control by PI controller with control by PI controller and sliding mode controller. It compare with speed response using MATLAB/SIMULINK.

각 원자력 발전소에서는 정밀성, 안전성을 확인하는 검사의 중요성을 인식하여 LPMS(Loose Part Monitoring System)을 사용하여 사고 징후를 조기에 감지하여 이에 대한 예방조치를 가능케 함으로써 설계기준 사고 발생을 사전에 방지할 수 있게 한다. 또한 이 기술은 신호 측정 및 분석 등의 기반기술 개발을 통하여 건전성 감시 기술의 신뢰성을 향상 시키고 있다. LPMS(Loose Part Monitoring System)기술은 재료, 기기, 구조물 등의 성질과 내부조직을 변화시키거나 파괴하지 않고, 배관내부에 흐르는 금속 파편들을 찾아내어 정밀성, 안전성, 신뢰성을 확보하기 위하여 검사기술이 적용되고 있다. 그러나 이 방법은 배관내의 이물질의 충격이 발생해야 감지가 가능하고, 이물질의 모양이나 사이즈를 확인하기에는 어려움이 있다. 따라서 본 논문에서는 배관외부에서 자기장을 인가하여, 배관내의 이물질에 변화하는 자기장을 홀센서로 측정하여 기존의 LPMS 방식을 보완하는 시스템을 개발하기 위해, 배관에 필요한 자기장 발생장치를 설계하고, 이물질을 검출하기 위한 검출 감도향상에 대해 연구하였다.

A down-scaled simulator is developed to simulate typical faults in induction motor such as short-turn stator winding, broken rotor bar, dynamic and static air-gap eccentricity, bearing trouble, and mechanical unbalance. The simulator is used as an initial builder to develop design algorithm for real-time faults detecting system by processing an abnormal signal and characteristics in each fault.

The line-start permanent magnet synchronous motor has a high efficiency and an advantage in constant speed operation regardless of the effect of load variation. However it is difficult to predict the performance of characteristics accurately, because of the unbalanced starting torque with the initial starting position of the rotor and the generation of a break torque. In this paper the dynamic characteristics of the line-start permanent magnet synchronous motor are described and compared with those of the squirrel-cage induction motor through the simulation to find the characteristics of the permanent magnets and the rotor bars in the line-start permanent magnet synchronous motor.

This paper describes the effects of air gap eccentricity in induction machines. Asymmetric electro-magnetic force caused by the frictional worn bearing, rotor misalignment and unbalanced rotor etc. generates an asymmetrical operation, vibration and electro-magnetic noise. The need for detection of these rotor eccentricities has pushed the development of monitoring methods with increasing sensitivity and noise immunity. In this paper, we focus on investigating the asymmetrical operation considering of unbalanced magnetic force in squirrel-cage induction motor with 380 [V], 7.5 [kW], 4P, 1,768 [rpm]. The effects of the rotor eccentricity, magnetic force are investigated by finite element method (FEM).

This paper presents an analytical solution to predict magnetic field distribution of permanent magnet synchronous motor equipped with surface-mounted magnet by using transfer relations in terms of two-dimensional model in polar coordinates. The analytical results are validated by comparison with finite element analyses (FEA).

This paper deals with design of a small-scaled permanent magnet generator (PMG) for wind power applications. First, this paper determines rated power and rated speed of the PMG from measured characteristics of wind turbines. Second, we derive analytical solutions for the open-circuit field in order to determine optimum magnet thickness and pole pitch/arc ratio. Third, on the basis of open circuit field solutions, stator magnetic circuit is designed. And then, a diameter of stator coil which agree with a required current density is calculated, and its turns are determined from the area of slot. Finally, finite element (FE) method is employed for validity of the designed PMG and, the back-emf measurements are also given to confirm the design.

This paper presents a analytical field solutions for the general class of Linear Brushless DC(LBLDC) motors with PM mover and 3-phase winding stator. In our magnetic field analysis, we have adopted an approach which can treat both magnetized material and winding from the each field analysis by magnetic vector potential considering 2-Dimensional slot modeling. Therefore, we give accurate analytical formulas and object function for design and parameters estimation by its magnetic field.

We investigated the operating characteristics of a flux-lock type superconducting fault current limiters according to the number of the serial connection each the superconducting element at the additive polarity winding of a transformer. This SFCL consists of two coils wound in parallel on the same iron core, and the secondary coil is connected to the elements in series. Operating characteristics can be controlled by adjusting the inductances and the winding directions of the coils. It turns ratio between the primary and the secondary coils is 63:21. The analysis of voltage, current, and resistance in serial connection each element was performed to increase the applied voltage of flux-lock type SFCL. When the applied voltage was 200/$\sqrt{3}[V_{rms}]$ with three elements connected in seres, the peak value of the line current increased up to 26,24[A]. On the other hands, resistive SFCL increased up to 36.35[A], under the same conditions. This enabled the flux-lock type SFCL to be easy to increase the capacity of power system.

This paper presents a study on the winding method and structure of core of single phase induction motor in order to design the high efficiency motor. In case of single phase induction motor, winding fill factor and the number of turns in each slot are not uniform in general. Moreover, these can be the critical parameters for high efficiency design in case the size of motor should be restricted within certain volume. Therefore, we should analyze the effects of these parameters related to efficiency parameter. The characteristic analysis was performed by using FEM.

본 논문은 전력기기에서 문제가 되는 온도상승에 대응하여 제품 개발시 선행 해석을 통한 온도 안정성 확보와 제품 신뢰성 향상, 설계 기간 단축을 위한 방안에 대하여 서술하고 있다. 전력기기의 온도 상승을 예측하기 위한 방법으로 전자계 해석과 열유동 해석을 동시에 수행하는 연계 해석법을 제안하며, 이 해석법의 검증을 위해 기중 차단기의 통전시 온도 상승에 대한 해석을 수행하였고, 실험을 통해 이름 검증하였다.

This paper present the Half-Bridge converter for low current output. In converter system, magnetic components are important devices used for energy storage, energy transfer, galvanic isolation and filtering. The proposed Half-Bridge converter is to reduce the number of magnetic components. The secondary rectification was discussed by comparison of center-tap type with primary center-core transformer winding and primary side-core transformer winding. A prototype featuring 400V input, 10V output, 400kHz switching frequency, and 100W output power.

In this paper, a new sensorless control based on an adaptive sliding mode observer is proposed for the interior permanent magnet synchronous motor(IPMSM) drives. With using voltage equation only, the adaptive sliding mode observer was investigated. The proposed adaptive sliding mode observer is applied to overcome the problem caused by using the dynamic equation. Furthermore, the Lyapunov theorem is used to prove the system stability included speed estimate and speed control. The effectiveness of the proposed algorithm is confirmed by the experiments.

Recently, the high frequency boost DC-DC converter has been widely used for the PCS system because of its small size and low cost. In this paper, the experimental results of the boost DC/DC converter using LLC series resonant converter are verified on the simulation based on the theoretical analysis and the lkW experimental prototype.

본 논문에서는 매입형 영구자석 동기전동기(IPMSM)의 속도추정을 위한 새로운 센서리스 알고리즘을 제안한다. 매입형 영구자석 동기 전동기의 기본 전압 방정식을 이용하여 회전자의 자속을 추정하고, 위상고정루프(PLL)를 사용하여 회전자의 위치와 속도를 추정하는 방법으로 센서리스 알고리즘을 구성하였다. Matlab SIMULINK를 이용한 시뮬레이션과 실험을 통하여 제안된 알고리즘을 검증하였다.

This paper presents the two lossless auxiliary inducors-assisted voltage source type half bridge(single ended push pull:SEPP) series resonant high frequency inverter for induction heated fixing roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation forwide its output power regulation ranges and load variations under constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operatprinciple is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation charactertics-based on the high frequency PDM strategy. The experimenoperating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimenones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliimplemented here is proved from the practical point of view.

The paper presents a sensorless speed control of interior permanent magnet synchronous motors using an adaptive integral binary observer in view of composition with a main loop regulator and an auxiliary loop regulator. The binary observer has a property of the chattering alleviation in the constant boundary layer; however, the steady state estimation accuracy and robustness are dependent upon with width of the constant boundary. In order to improve the steady state performance of the binary observer, the binary observer is formed by adding extra integral dynamic to the switching hyperplane equation.

We proposed a new sustaining driver for AC PDPs with reduced sustain voltage by half, which cope with the demerits of the conventional TERES circuit. In the proposed circuit, the number of active switching elements are smaller than the TERES circuit by two and the energy recovery circuit is added. In this paper, the proposed circuit is implemented with control circuits and its validity is verified by the experimentation.

This paper proposes a DC-DC converter which is able to charge and discharge secondary batteries. The converter operates as a double-ended forward converter in charging process and as electrical isolated boost converter in discharging process. The converter is designed for continuous current operation. The switching frequency is selected as 100kHz to reduce the size of both the inductor and the capacitor.

논문은 전류원 HVDC로 연계되어 있는 제주-해남 계통을 전압원 HVDC로 연계하였을 경우에 대한 특성 분석에 대해서 기술하고 있다. 기존의 제주-해남 HVDC시스템은 교류계통 전압의 외란에 의해서 전류실패가 발생할 수 있으므로 연계되는 교류계통 모선에 무효전력보상설비들이 설치되어 있다. 따라서 기존의 전류원 HVDC 시스템은 대용량의 전력을 전송할 수 있다는 장점이 있는 반면 추가로 무효전력 보상설비들이 설치가 되어야 한다는 단점이 있기 때문에 최근에 선진국에서는 전압원 HVDC 시스템에 대한 연구가 활발히 진행되고 있다. 전압원 HVDC 시스템은 계통사고 또는 교류전압강하로 인한 전류실패가 발생하지 않고, 무효전력을 HVDC 시스템의 용량내에서 유효전력과 독립적으로 제어될 수 있기 때문에 추가로 무효전력 보강설비가 필요하지 않다는 장점이 있다. 본 논문에서 늘 제주-해남 계통을 전압원 HVDC로 연계하는 모델을 PSCAD/EMTDC를 이용해서 개발하였다. 개발된 시뮬레이션 모델은 전압원 HVDC를 이용해서 제주-해남 계통을 연계하였을 경우에 대한 동특성을 분석하는데 유용하리라 사료된다.

This paper describes experimental analysis of UPQC, which is composed of cascaded H-bridges and single-phase multi-winding transformers. The operational characteristic was analyzed through experimental works with a scaled model, and simulations with PSCAD/EMTDC. The UPQC proposed in this paper can be directly connected to the distribution line without series injection transformers. It has flexibility to expand the operation voltage by increasing the number of H-bridge modules. The analysis results can be utilized to design the actual UPQC system applicable for the actual distribution system.

This paper deals with an analysis of SCR thyristor switching pattern for a power quality disturbance generator with phase jump function. The proposed generator can be applied to the performance test of custom power devices. Voltage sag, swell, outage, unbalance and phase jump after outage are provided by the generator. The phase jump operating principle of the generator is described and analysed. Especially, a proper switching of the SCR thyristors for the proposed generator is important to guarantee the system reliability. Therefore the switching patterns for the thyristors in each made were analysed.

This paper presents the single-stage High Power Factor TSFC(Two-Switch Forward Converter). Recently, due to growing concern about the harmonic pollution of power distribution systems and the adoption of standards such as ICE 61000-3-2 and IEEE 519, There is a need to reduce the harmonic contents of AC line currents of power supplies. This research proposed the single-stage two switch forward circuit for low voltage and high current output. The principle of operation, feature and design considerations are illustrated and verified through the experiment with a 200W(5V, 40A) 200kHz MOSFET based experimental circuit.

Speed and torque controls of permanent magnet synchronous motors are usually attained by the application of position and speed sensors. However, speed and position sensors require the additional mounting space, reduce the reliability in harsh environments and increase the cost of a motor. Therefore, many studies have been performed for the elimination of speed and position sensors. This paper investigates a novel sensorless control of a permanent magnet synchronous motor. The proposed control strategy utilizes the active and reactive torque control for maximizing the active torque of a sensorless PMSM. The proposed algorithm is verified through the simulation and experimentation.

같은 정격의 자계결합형 단권변압기와, MOSFET로 구성된 반도체 변압기의 효율을 비교하였다. 두 변압기의 생산원가를 비슷한 정도로 맞추고 출력 정격도 같은 규격으로 일치시키고 그 성능을 비교하였다. 기존의 자계결합형 단권변압기와 반도체 변압기의 무부하시와 부하시의 전력을 측정하고 이 두 종류의 변압기의 손실을 분석하였다.

전류 미러회로를 이용한 직류 전류 센서를 이용하면 간단하게 전류센서회로를 구성할 수 있다. 더우기 Shunt 저항에서 낮은 전압을 이용하므로 효율적인 전류감지회로를 구성할 수 있다. 그러나 트랜지스터의 에미터 베이스 전압을 이용하므로 비 직선성이 두드러진다. 이 회로의 전류센서, 온도특성등 여러 전기적 물리적 특성을 이해하고 이를 마이크로프로세서를 이용하여 그 특성을 상쇄하는 구성을 고려하여 보기로 한다.

비정질 합금재료와 페라이트를 사용하여 비접촉식 커플러를 제조하여 각각의 재료가 적용가능한 범위를 규명하고자 하였다. 비정질 합금재료에 비해 페라이트는 안정적인 특성을 발휘하는 주파수 대역이 좁으며, 낮은 포화자속밀도로 인해 내전류 특성이 떨어졌다. 즉 페라이트는 20 MHz 이하의 주파수 대역과 비정질 재료가 적용되는 선로보다 유입전류가 낮은 전력선에 적용 가능할 것으로 보인다.

A new soft switched active snubber circuit is proposed to achieve zero voltage and zero current switching for all the switching devices in PWM DC-DC converters. The unique location of the snubber and inductor ensures low current/voltage stresses and commutation losses. With a saturable reactor, the conduction loss of auxiliary switch could be further minimized. A boost converter adopting this technique is presented as an example, to illuminate its operation principles and derive the design procedures. Simulation and hardware implementation have been made to validate its performance. Some other basic PWM DC-DC topologies using the proposed snubber have also been given.

This paper presents a impedance model for the simulation of both static and dynamic characteristics of the electrodeless fulorescent lamp. A behavioral, PSpice compatible, model has been developed for the electrodeless fluorescent lamp. The model was tested at steady-state for different power levels, with an LCC modulated drive. and this model is established from some equations and measured electrical characteristics of EEFL. The validity of proposed lamp model is verified from the simulation and experimental results.

In this paper, a new single phase voltage sag/swell compensator using direct power conversion is introduced. A new compensator consists of input/output filter, series transformer and direct ac-ac converter, which is a single-phase back-to-back PWM converter without dc-link capacitors. Advantages of the proposed compensator include: simple power circuit by eliminating dc-link electrolytic capacitors and thereby, improved reliability and increased life time of the entire compensator; simple PWM strategy to compensate voltage sag/swell at the same time and reduced switching losses in the ac-ac converter. Further, the proposed scheme is able to adopt simple switch commutation method without requiring complex four-step commutation method commonly required in the direct power conversion. Simulation results are shown to demonstrate the advantages of the new compensator and PWM strategy.

This paper proposes a Chaos Pulse Width Modulation(CPWM) technique. For generating the chaotic numbers by chaos phenomenon, chaos area $\lambda$=0.99 in bifurcation tree of the proposed double tent mapping is used. A micro-controller is used for the generation of chaos numbers and triangular carrier with chaotic frequency is obtained through the process of frequency modulation according to the generated chaos numbers. The experiments are executed with the 1.5kw induction motor coupled with a 2.5A load. The experimental results show that the voltage / current spectra are spread to a chaotic range, and the switching noise of motor is reduced by the proposed method compared to the fixed frequency PWM method.

This paper proposes a snubber circuit for a PWM Cuk AC-AC converter. The proposed snubber makes use of an Undeland snubber as a commutation aids. So the snubber keeps such good features as small count of snubber elements, reduction of voltage/current stress of main switching devices and improved efficiency. This paper shows simulation results to verify the adaptability and feasibility of the proposed snubber.

In this paper, a novel type of auxiliary active snubbingcircuit assisted quasi-resonant soft-switching pulse width modulation inverter is proposed for consumer induction heating equipments. The operation principle of this high frequency inverter is described using switching modes and equivalent circuits. This newly developed series resonant high frequency inverter can regulate its high frequency output AC power under a principle of constant frequency active edge resonant soft- switching commutation by asymmetrical PWM control system. The high frequency power regulation and actual power conversion efficiency characteristics of consumer induction heating (IH) products using the proposed soft-switching pulse width modulation (PWM) series load resonant high frequency inverter evaluated. The practical effectiveness and operating performance of high frequency inverter are discussion on the basis of simulation and experimental results as compared with the conventional soft-switching high frequency inverter.

This paper presents two new circuit topologies of DC bus lineside active edge resonant snubber assisted soft-switching PWM full-bridge DC-DC converter acceptable for either utility AC 200V-rms or AC 400V-rms input voltage source. All the active power switches in the full-bridge arms and DC busline can achieve ZCS turn-on and ZVS turn-off commutations and the total turn-off switching power losses of all active switches can be reduced for high-frequency switching action. The effectiveness of these new DC-DC converters topologies is proved for low voltage and large current high efficiency DC-DC power supplies as TIG arc welding machine from a practical point of view.

Smart열차진로제어시스템은 기존 전자연동장치에서 사용하고 있는 궤도회로방식의 열차점유정보대신에 열차의 실시간 위치정보를 사용하여 열차의 진로를 제어한다. 이에 smart열차진로제어시스템에 적용되는 새로운 연동논리를 검증하기 위해서 소형전동기의 속도제어를 통하여 생성되는 회전신호를 사용하여 열차의 이동 및 속도를 계산하고, 선로설정, 열차간격 제어, 진로제어, 열차모의장치 및 연동처리를 할 수 있는 모의장치를 구축하였다. 여기에서는 Smart열차진로제어시스템의 진로제어 알고리즘 설계, 장치설계 등의 제반 내용을 확인하였다.

현재 세계적인 열차제어의 추세는 궤도회로에 의한 고정폐색방식을 이용한 열차 운행이 아닌 발리스 또는 무선통신에 의한 이동권한을 이용한 열차제어방식을 적용하고 있으며, 국내에서도 이에 맞추어 철도청에서는 ATP 사업을 통하여 유럽의 ERTMS/ETCS 규격에 의한 발리스 기반의 열차제어시스템을 적용할 계획이다. 또한 분당선에서는 통신기반 열차제어시스템인CBTC 시스템을 시범구축하고 있다. 이러한 추세에 맞추어 열차제어시스템에 있어서 가장 중요한 기능 중의하나인 안전제동 기능을 이동권한에 적합하도록 새롭게 모델링할 필요가 있으며, 본 논문에서는 이러한 이동권한에 의한 열차제어시스템의 안전제동에 대해 연구하였다.

철도 신호제어시스템은 철도의 선로변에 위치하면서 열차의 안전운행을 책임지는 매우 중대한 시스템이다. 이러한 신호제어장치들은 각자의 고유의 기능을 수행하면서 다른 제어장치들과 링크되어 하나의 신호제어시스템으로 구성되어진다. 요즘 철도신호시스템에 사용되는 각 장치들이 전자화되어감에 따라 철도신호장치들간 정보전송을 위한 네트워크에 대한 중요성이 증대되었다. 철도신호시스템과 같은 고신뢰성이 요구되는 시스템에서 실시간 요구조건과 신뢰도를 만족시킬 수 있는 네트워크 기술에 대한 필요성 또한 증대되고 있다. 가장 널리 쓰이는 기술인 이더넷은 프로토콜 자체의 랜덤 특성으로 인해 실시간 요구사항을 만족하지 못하였으나 최근 들어 스위치드 이더넷으로 진화하면서 산업용 제어시스템에 이더넷 기술이 적용되고 있다. 본 논문에서는 이러한 스위치드 이더넷의 이론적 해석을 통해 철도신호시스템에 적용 가능성을 확인하였고, 네트워크에 결함발생 시 결함검지 및 회복 알고리즘이 포함된 높은 신뢰성을 가진 이더넷 기반 네트워크 알고리즘과 모의시험을 통한 그 성능을 분석하였다.

This paper presents a method to optimize train radio communication network for train control (CBTC) or multimedia services. To determine the optimized distance between wayside radio stations in a radio communication network constructed along railway, radio frequency allocation and hand-over capability is studied in terms of radio communication cell coverage and roaming feasibility.

The changeable set system need to be developed to devoid a traffic congestion for rush hour. We will apply the changeable set system to solve this problems. The cost-effectiveness is reviewed when we apply this system on Korean urban transit system.

According to speed elevation of internal railroad, Seoul-Busan high-speed railway was opened up. Setting hereupon speed elevation of old line propel. Therefore, research and development about Tilting train are propel by one of method that do not need huge investment such as earthwork serving speed elevation of general railroad. Studied about car report lake this treatise applies in Tilting train's signal control.

전기철도차량에서 사용한 부하전류는 귀환 회로인 궤도를 통해 변전소로 유입한다. 전기철도차량에서 사용하는 전력변환장치 때문에 부하전류에는 고조파가 함유되고 이 고조파 전류는 외부통신선에 영향을 주지 않아야 한다. 본 논문에서는 한국형 고속열차를 대상으로 고조파 전류를 측정하여 외부통신선 영향을 평가하는 등가방해전류로 환산하고 그 기준으로 평가한 결과를 소개한다.

There are operated the six thousand train in the interior of a country. 95% of them are possible usage of resuscitation. Especially, Among them VVVF-Inverter vehicle has a merit of the highest recycle rate. but we don't use a apt recycled energy. Although the existing recycle energy used inverter method supply with electric power, it is decided in accordance with the state of sources. So efficiency of recycled electric power is of poor quality and catenary-voltage-fluctuation be generate because of recycled electric power. and it is able to affect system of safety train service. We'll research the method of supply according to wire condition after storing recycle energy made during train's stopping relation to Advanced EMU Research. Those methods are divided SMES, Fly-Wheel and Supercapacitor, and Considering the both economical efficiency and system application, we'll develop recycle energy storage system suitable our country condition.

Maglev using EMS becomes unstable by unexpected big air-gap disturbance. The main causes of the unexpected air-gap disturbance are step-wise rail joint and large distance between rail splices. For the stable operation of the Maglev, the conventional system uses the threshold method, which selects one gap sensor among two gap sensors installed on the magnet to read the gap between magnet and guide rail. But the threshold method with a wide bandwidth makes the discontinuous air-gap signal at the rail joints because of the offset in air gap sensors and/or the step-wise rail joins. Further more, in the case of the one with a narrow bend-width, it makes Maglev system unstable because of frequent alternation. In this paper, a new method using fuzzy rule to reduce air-gap disturbances proposed to improve the stability of Maglev system. It treats the air-gap signal from dual gap sensors effectively to make continuous signal without air gap disturbance. Simulation and experiment results proved that the proposed scheme was effective to reduce air-gap disturbance from dual gap sensors in rail joints.

Being controlled by a pole placement, levitation system should need many sensors that measure air-gap, velocity, acceleration, and so on. However, these sensors have observational errors by changed temperature. This paper proposed a output compensated command tracking controller for reducing the error and reducing sensors. Simulation results will be provided to show the validity of the proposed scheme.

It can be considered that the safety of software is combined with that of hardware, and also directly connected to system safety. Because the software in the railway system takes the form of Embedded that let it behave at the system level, instead of independent operation, the safety of the railway S/W is also important. The approach, for ensuring the quality and safety of those software, can be considered with two points of view. Those are views seeing from products, and from processes. The two points of approach are all necessary in the railway system. For the first of all, the process approach is to validate maturity of the organizations in accordance to the judging processes of organizations, which are specified by CMMI(Capability Maturity Model Integration) or SPICE(Software Process Improvement and Capability dEtermination: ISO/IECl5504). In this paper, as the first step of them, we are trying to find approaches to estimate the maturity of manufacturer and assessment organization in the railway system.

안전필수시스템인 철도신호제어 시스템의 신뢰성은 하드웨어와 소프트웨어의 신뢰도에 의해서 결정된다. 하드웨어의 신뢰도는 상대적으로 많은 연구와 환경적 시험을 통하여 비교적 용이하게 예측하고 입증할수 있으나, 소프트웨어의 신뢰도는 반복실험결과에 의해서 추정해야 하므로, 입력 값에 따라서 신뢰도 추정치가 종속된다. 소프트웨어의 입력과 출력의 조합은 거의 Combinatoric으로 되기 때문 모든 경우를 시험하기는 블가능하다. 따라서 단순화된 방법에 의해서 소프트웨어의 신뢰도를 구하는 것이 중요한 문제로 부각되고 있다. 본 연구에서는 소프트웨어의 신뢰도를 예측하는 신뢰도 예측방정식(Reliability Prediction Equation)을 도출하여 신호제어시스템 소프트웨어에 대한 신뢰도 모델링을 수행하고자 한다.

CBTC 시스템에서는 선로변에에 설치된 선로변무선기(Wayside Radio Set 이하, WKS)가 상호 무선통신을 수행하고, 각 WRS간의 거리를 항상 측정하고있도록 설계되었다. CBTC지상장치가 WRS간에서 측정된 WRS간 측정거리를 SRS에서 수신하고, log의서 기록한다. 기록한 로그를 이용하여 적정값을 판단한다. 본 시험에서는 WRS간의 무선통신에서 안정적인 측정 데이터가 취득되는지를 확인하였다.

In this paper an integrated model of PV-AF (Photovoltaic-Active Filter) and PV-SPE (Photovoltaic Solid Polymer Electrolyte) system using PSCAD/EMTDC were explained in detail. The main concept of PV-AF system starts from the "harmonics". In order to deliver power to utility, PV system essentially needs a converter system. Here PV-AF system adds the function of active filter to the converter system installed in PV system, which was introduced already in several papers. PV-SPE system has been studied as a replacement of existing hydrogen production technology that emits large amount of carbon dioxide into atmosphere. Until now, these two systems, PV-AF and PV-SPE, have been considered separately. However, in this paper, characteristics and advantages of combined system are discussed in detail.

In this paper, a novel algorithm for increasing the steady state efficiency during light load operation of the induction generator that integrated with a wind power generation system is presented. The proposed algorithm based on the flux level reduction, where the flux level is estimated using Support-Vector -Machines for regression (SVR) for the optimum d-axis current of the generator. SVR is trained off-line to estimate the unknown mapping between the system's inputs and outputs, and then is used online to calculate the optimum d-axis current for minimizing generator loss. The experimental results show that SVR can define the flux-power loss accurately and determine the optimum d-axis current value precisely. The loss minimization process is more effective at low wind speed and the percent of power saving can approach to 40%.

The high efficiency full-bridge LLC resonant converter using a contact-less transformer is proposed for the photovoltaic power generation system. For the series resonance with a series capacitor, the LLC resonant converter utilizes the leakage inductance and magnetizing inductance of a contact-less transformer. Unlike the conventional series resonant converter operated to the continuous resonant current at above resonance frequency, the proposed converter operates to the discontinuous resonant current at the narrow frequency control range below resonance frequency. Due to the discontinuous mode resonant current, the proposed converter can be achieved the zero voltage switching (ZVS) in the primary switches and the zero current switching (ZCS) in the secondary rectification diodes without any auxiliary circuit. In this paper, the experimental results of the proposed full-bridge LLC resonant converter using a contact-less transfonner are verified on the simulation based on the theoretical analysis and the 150W experimental prototype.

Recently, a fuel cell with low voltage and high current output characteristics is remarkable for new generation system It needs both a DC-DC step-up converter and DC-AC inverter to be used in fuel cell generation system Therefor, this paper, consists of an isolated DC -DC converter to boost the fuel cell voltage 380[$V_{DC}$] and a PWM inverter with LC filter to convent the DC voltage to single phase 220[$V_{AC}$]. Expressly, a tapped inductor filter with freewheeling diode is newly implemented in the output filter of the proposed high frequency isolated ZVZCS PWM DC-DC converter to suppress circulating current under the wide output voltage regulation range, thus to eliminate the switching and transformer turn-on/off over-short voltage or transient phenomena Besides the efficiency of 93-97[%]is obtained over the wide output voltage regulation ranges and load variations.

A study of the photovoltaic generation system tend to concentrate its importance on specific filed such as analysis of photovoltaic characteristic, improvement of a inverter, and controller. In this paper, a practical facility of the photovoltaic generation system and connection of its organization are presnted with process of 1.2kW prototype. From the results of monitoring system which is for reliability and analysis of the photovoltaic generation system, stability of the system was confirmed.

태양전지는 일사량에 따라 그 출력특성이 변하기 때문에 전지로부터 최대출력을 얻기 위해서는 컨버터에 의한 최대 전력점 추종제어가 필요하다. 본 논문에서는 태양광 발전시스템의 최대전력추종을 위해 퍼지이론을 도입한 퍼지제어기를 설계하였다. 퍼지제어기의 디지털 설계를 위해 태양광 발전시스템을 각 부분을 구성하고, FPGA를 사용하여 제어기를 구현하였다. 또한 실험을 통해 FPGA의 퍼지제어기로서의 구현가능성을 발견하고 그 타당성을 입증하고자 한다.

This paper presents a novel DC-DC Converter for 3 [kW] Fuel Cell System Residential Application. Phase shifted control is employed to regulate the output voltage and achieve soft switching. The transformer leakage inductance is utilized effectively to achieve zero voltage turn on for the power semiconductor switches. The current doubler rectifier has only one diode drop. The transformer secondary winding current rating is one half the load current. The overall effciency of the converter is improved.

The objective of this research is to investigate usage of 3KW photovoltaic-wind power hybrid generation system composed of 500W solar power generator and 400W wind power generator in a parallel circuit. In addition, solar radiation meter and wind monitor have been installed into each generation system to obtain the practical operating data that monitored in monthly, daily and hourly. These data that are independent to weather change and location would provide adequate generation output on average and cope with emergency situation in generation system In conclusion, based on this study, it could be considered for 3KW combined generation system to be gradually propagated to houses and small-size public facilities.

반도체에 이온화 방사선을 조사시키면 소자 내부에서 전자-전공쌍(Electron-Hole Pair, EHP) 생성현상이 나타난나. 이 발성 전하는 방사선원에 따라 반영구적인 전원으로 활용이 가능하다. 본 논문에서는 반감기가 100여년인 Ni-63 베타 방사성 능위원소와 PN 접합형 반도체 소자를 사용한 방사선 전지를 개발하기 위한 연구의 일환으로 효율적인 방사광 변환 법과 전류 발생방법 및 전지회로 구현에 대해서 고찰하였다. 또한 Ni-63 방사선의 베타선 스펙트럼을 계산하고 이에 해당하는 광입력 특성에 대한 실리콘 PN 접합 다이오드의 반응특성을 태양광 시뮬레이션용 소프트웨어를 사용하여 검증하였다.

This paper proposes a parallel operation system of the Z-source active power filter using one fuel cells(FC) system. The proposed system is composed of two Z-source inverters operating in parallel only one PEM(Polymer Electrolyte Membrane)FC system. Also, as the control algorithm of the active power filter, a single phase P-Q theory and PI control are adopted. The effectiveness of the proposed the system is verified by the PSIM simulation in the steady state and the transient state.

본 연구에서는 기 설치된 능동전력필터와 연료전지 Z-소스 능동전력필터의 병렬운전 시스템을 제안하였다. 제안된 시스템은 이미 설치되어 운전 중인 단상 V-소스 병렬형 능동전력필터와 병렬로, 연료전지(FC) Z-소스 능동전력필터를 설치하여, 전체 능동전력필터 시스템의 용량 증가를 도모할 수 있었다. 제안된 방법의 타당성은 전력전자 전용 PSIM시뮬레이션에 의하여 과도상태 및 정상상태에서 확인하였다.

신재생에너지의 보급이 증가하면서 기존의 시스템과 신규 설치되는 시스템을 원격지에서 효율적으로 관리하는 모니터링 기술이 필수가 되었다 이들 모니터링 기술에는 발전 출력량과 기상조건 등의 복합적 요소 모니터링 기술이 필요하다. 다중 채널을 이용하여 모니터링 하는 기법은 통신속도와 S/W, H/W에 따라 각각여러가지 방법이 있으며 최대채널의 제한, 가격적인 부분까지 많은 부분을 고려해야 한다. 본 논문에서는 기존수행하고 있는 모니터링 기술을 분석하여 신재생에너지 시스템에 적합한 다중채널 모니터링 기법을 제안하고자한다.

This paper summarizes the results of these efforts by offering a photovoltaic system structure in 50kW large scale applications installed in Chosun University dormitory roof and simulation tool. This describes configuration of utility interactive photovoltaic system which generated power supply for dormitory. In this paper represent 50kW utility PV system examination result.

BIPV(Building Integrated PV) system can expect dual effects that reduce expenses for establishment of PV system by adding new function as outer covering material of building expect producing the electricity. In case of PV(photovoltaic system) there are many generation differences according to the exterior environmental facts(solar cell array, design and installation condition of interactive inverter system). In this paper, we compared constitute factors of 3kW BIPV(solar cell module, inverter), operating characteristic and total system characteristic(utilization, generation efficiency, loss fact) and found out long time operating data using a watch instrumentations. By use of long time operating result, compare a totally operating characteristics, and we proposed a next building application of BIPV. BIPV system that is proposed in this paper, was established in Solar Energy research center of Chosun University, composed with system. The objective of this paper, is to provide a efficient BIPV design method through the considerations for the integration of PV system.

We investigated the operational characteristics of the hybrid-type superconducting fault current limiter (SFCL) according to the serial and parallel connections of secondary circuits. The hybrid-type SFCL consists of a transformer, which has a primary winding and several secondary windings with $YBa_2Cu_3O_7$ films connected in series and parallel. In order to increase the capacity of the SFCL, the serial connection between each current limiting unit is necessary. The hybrid-type SFCL with the serial connection in secondary circuits could show superior characteristics than those of the parallel connections in the current limiting and quench time. The resistances generated in the superconducting units were also lowered at the parallel connections. We confirmed that the parallel connection reduced the power burden of each superconducting unit under the same conditions because of the simultaneous quenching between superconducting units.

논문에서는 SPWM인버터의 출력파형을 개선하고 고조파 성분을 저감시키기 위한 방법으로 스위칭 기법과 LC필터를 제안한다. 스위칭 기법은 일정 고조파 이하를 제거할수 있으나 스위칭 손실을 수반함으로 고차 고조파를 제거하기에는 제약이 많은 따른다 LC필터는 고조파 성분들을 제거할 수 있으나 출력파형의 왜곡을 초래한다. 본 연구에서는 스위칭 기법으로 기뜬 주파수 근처의 고조파를 제거하고 LC필터를 이용하여 나머지 고조파 성분을 제거하는 방법을 시뮬레이션을 통하여 검토하여 보았다. LC필터의 출력파형 왜곡을 보상하기 위하여 필터에 저항을 직렬 연결하였다.

Electro-magnetic launcher(EML)는 전자기력을 이용하여 발사체를 추진시키는 장치이며 그 종류에는 레일건과 코일건이 있다 본 논문에서는 소형, 경량의 발사체를 추진, 가속시키기 위한 솔레노이드형 EML을 설계, 제작하여 시험 발사하고 그 특성을 분석하였다. 개발된 EML은 소형이기 때문에 launcher의 직경이 작아 자기장을 한 지점으로 집중시키는 장치가 필요없고, 전기에너지를 줄이기 위한 별도의 시스템이 필요하지 않으며, 솔레노이드의 형태와 발사체의 위치, 스위칭 시간에 의해 발사체의 추진력과 속도를 조절할 수 있는 장점이 있었다.

자기누설 탐상시스템은 자성체인 구조물에 서검사 대상 물체를 자화시켜 결함부위에서 자기 누설의 여부를 측정함으로써 구조물의 결함, 부식 등을 탐지하는 시스템이다. 본 논문에서는 소형 비파괴 검사시스템을 설계하고 제작하였다. 또한 3차원 유한요소법을 이용하여 해석하고 측정하여 결과를 비교 분석하였다.

To chase maximum power point at every moment under a conventional MPPT control method, a voltage and current coming out from PV-cell are needed to be feedbacked. So, the structure of control circuit becomes so complex and the MPPT control is in risk of control failure. In the newly developed control method, the current flowing into SPE cell is the only one considerable factor. So, the structure of control circuit becomes simple and the manufacturing cost of the control device decreases. Especially, in case of a huge system of PV-SPE system, because the voltage coming out from PV-cell is not needed to be feed backed, this system can be operated much more safely. In this paper, the PV-SPE system was actually manufactured based on the simulation model of PSCAD/EMTDC program and the results tested were shown. Authors are sure that it is the most useful method to maximize power from PV to SPE with only a feedback of SPE input current.