References
- Z. W. Zhong, "Overview of wire bonding using copper wire or insulated wire", Microeletronics Reliability, 51(1), 4-12 (2011). https://doi.org/10.1016/j.microrel.2010.06.003
- H. Kang, et al., "TLP and Wire Bonding for Power Module", J. Microelectron. Packag. Soc., 26(4), 7-13 (2019).
- B. Kim, et al., "Study on Sn-Ag-Fe Transient Liquid Phase Bonding for Application to Electric Vehicles Power Modules", J. Microelectron. Packag. Soc., 30(4), 61-68 (2023).
- P. Korzhavyi and B. Johansson, "Literature review on the properties of cuprous oxide Cu2O and the process of copper oxidation", TR-11-08, ISSN 1404-0344 (2011).
- G. Lee, et al., "Review on Oxidation Resistance Technology for Copper Nanowire Transparent Electrodes", J. Microelectron. Packag. Soc., 30(2), 21-32 (2023).
- C. Chen, et al., "Evaluation of Corrosion Resistance of AgAlloy Bonding Wires for Electronic Packaging", in IEEE Transactions on Components, Packaging and Manufacturing Technology, 8(1), 146-153 (2017). https://doi.org/10.1109/TCPMT.2017.2765899
- M. D. Groner, et al., "Gas Diffusion barriers on polymers using Al2O3 atomic layer deposition", Applied Physics Letters, 88, 051907 (2006).
- S.-H. K. Park, et al., "Ultrathin film encapsulation of an OLED by ALD", Electrochemical and Solid-State Letters, 8(2), H21 (2005).
- M. A. Hoque, et al., "Effects of humidity and phosphor on silicone/phosphor composite in white light-emitting diode package", Journal of Materials Science: Materials in Electronics, 30, 20471-20478 (2019). https://doi.org/10.1007/s10854-019-02393-8
- S. Park, et al., "Underfill acceleration factor based on thermal fatigue crack growth rate", 2010 Proceedings 60th Electronic Components and Technology Conference (ECTC), 5490925 (2010).
- S. Park and C. Feger, "Crack growth rate of thermally induced underfill fatigue", 2009 59th Electronic Components and Technology Conference, 5074170 (2009).
- S. Park, K. M. Liechti, and S. Roy, "A Nonlinear Viscoelastic Fracture Analysis of Concrete/FRP Delamination in Aggressive Environments", International Journal of Fracture, 142, 9-27 (2006).
- N. Badwe, et al., "Interfacial fracture strength and toughness of copper/epoxy-resin interfaces", Acta Materialia, 103, 512-518 (2016). https://doi.org/10.1016/j.actamat.2015.10.009
- C. Q. Cui, et al., "Surface treatment of copper for the adhesion improvement to epoxy mold compounds", 48th Electronic Components and Technology Conference (Cat. No.98CH36206), 678863 (1998).
- J. Liu, et al., "Fracture behavior of an epoxy/aluminum interface reinforced by sol-gel coatings", Journal of Adhesion Science and Technology, 20(4), 277-305 (2006). https://doi.org/10.1163/156856106776381811
- S. Park, "Au-Less, Ni-Less & Roughness-Less PCB Cu Surface Treatment Using All-in-One Al2O3 Passivation", 71st Electronic Components and Technology Conference (ECTC), 00111 (2021).
- H. Xu, et al., "Behavior of aluminum oxide, intermetallics and voids in Cu-Al wire bonds", Acta Materialia, 59(14), 5661-5673 (2011). https://doi.org/10.1016/j.actamat.2011.05.041
- H. G. Kim, et al., "Microstructural evaluation of interfacial intermetallic compounds in Cu wire bonding with Al and Au pads", Acta Materialia, 64, 356-366 (2014). https://doi.org/10.1016/j.actamat.2013.10.049
- A. G. Evans, et al., "Interface adhesion: effects of plasticity and segregation", Acta Materialia, 47(15-16), 4093-4113 (1999). https://doi.org/10.1016/S1359-6454(99)00269-4
- W. Fu-liang, et al., "Dynamics of Free Air Ball Formation in Thermosonic Wire Bonding", IEEE Transactions on Components, Packaging and Manufacturing Technology, 2(8), 1389-1393 (2012). https://doi.org/10.1109/TCPMT.2012.2189114