Computers and Concrete

  • 제33권5호
  • /
  • Pages.519-533
  • /
  • 2024
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Investigation of rate dependent shear bond properties of concrete masonry mortar joints under high-rate loading

  • John E. Hatfield (U.S. Army Engineer Research and Development Center, Geotechnical and Structures Laboratory) ;
  • Genevieve L. Pezzola (U.S. Army Engineer Research and Development Center, Geotechnical and Structures Laboratory) ;
  • John M. Hoemann (U.S. Army Engineer Research and Development Center, Geotechnical and Structures Laboratory) ;
  • James S. Davidson (Department of Civil Engineering, Auburn University)
  • 투고 : 2023.11.21
  • 심사 : 2024.02.07
  • 발행 : 2024.05.25
⟨ 이전 논문 다음 논문 ⟩

초록

Many materials including cementitious concrete-type materials undergo material property changes during high-rate loading. There is a wealth of research regarding this phenomenon for concrete in compression and tension. However, there is minimal knowledge about how mortar material used in concrete masonry unit (CMU) construction behaves in high-rate shear loading. A series of experiments was conducted to examine the bond strength of mortar bonded to CMU units under high-rate shear loading. A novel experimental setup using a shock tube and dynamic ram were used to load specially constructed shear triplets in a double lap shear configuration with no pre-compression. The Finite Element Method was leveraged in conjunction with data from the experimental investigation to establish if the shear bond between concrete masonry units and mortar exhibits any rate dependency. An increase in shear bond strength was observed when loaded at a high strain rate. This data indicates that the CMU-mortar bond exhibits a rate dependent strength change and illustrates the need for further study of the CMU-mortar interface characteristics at high strain rates.

키워드

과제정보

The lead author (J.E.H.) received support through the SMART fellowship from the U.S. Department of Defense, which provided valuable support and gave ample opportunity to receive guidance from highly knowledgeable individuals at the U. S. Army Engineer Research and Development Center (ERDC). The use of trade, product, or firm names in this document is for descriptive purposes only and does not imply endorsement by the U.S. Government. The tests described and the resulting data presented herein, unless otherwise noted, are based on work conducted by the U.S. Army ERDC. Permission was granted by the Director, Geotechnical and Structures Laboratory to publish this information. The support and expertise provided by the Concrete Masonry and Hardscapes Association (CMHA) was invaluable. Their knowledgeable laboratory staff conducted the standard ASTM masonry tests with precision and gladly answered any questions. They also modified their testing equipment to successfully execute the EN 1052-3 static shear test, which does not fall in their standard test suite.

참고문헌

  1. Abdou, L., Saada, R.A., Meftah, F. and Mebarki, A. (2006), "Experimental investigations of the joint-mortar behavior", Mech. Res. Commun., 33(3), 370-384. https://doi.org/10.1016/j.mechrescom.2005.02.026.
  2. Al-Salloum, Y., Almusallam, T., SIbrahim, S.M., Abbas, H. and Alsayed, S. (2015), "Rate dependent behavior and modeling of concrete based on SHPB experiments", Concrete Concrete Compos., 55, 34-44. https://doi.org/10.1016/j.cemconcomp.2014.07.011.
  3. ASTM International (2016), ASTM C1552-16 Standard Practice for Capping Concrete Masonry Units, Related Units and Masonry Prisms for Compression Testing, ASTM International, West Conshohocken, PA, USA.
  4. ASTM International (2019), ASTM C1072-19 Standard Test Methods for Measurement of Masonry Flexural Bond Strength, ASTM International, West Conshohocken, PA, USA.
  5. ASTM International (2021a), ASTM C90-21 Standard Specification for Loadbearing Concrete Masonry Units, ASTM International, West Conshohocken, PA, USA.
  6. ASTM International (2021b), ASTM C109-21 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50 mm] Cube Specimens), ASTM International, West Conshohocken, PA, USA.
  7. ASTM International (2021c), ASTM C1314-21 Standard Test Method for Compressive Strength of Masonry Prisms, ASTM International, West Conshohocken, PA, USA.
  8. ASTM International (2022), ASTM C140-22a Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units, ASTM International, West Conshohocken, PA, USA.
  9. Atkinson, R.H., Amadei, B.P., Saeb, S. and Sture, S. (1989), "Response of masonry bed joints in direct shear", J. Struct. Eng., 115(9), 2276-2296. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:9(2276).
  10. Bazant, Z.P., Gu, W.H. and Katherine, T.F. (1995), "Softening reversal and other effects of a change in loading rate on fracture of concrete", ACI Mater. J., 92(1), 3.
  11. Beattie, G. (2003), "Joint fracture in reinforced and unreinforced masonry under quasi-static and dynamic loading", Doctoral Dissertation, Univeristy of Liverpool, Liverpool, UK.
  12. Bewick, B., Rolater, G., Bui, J., Barsotti, M., Ziemba, A., Sanai, M. and Laney, C. (2017a), "Fragmentation of solid materials using shock tubes Part 1: First test series in a small-diameter shock tube", DTRA-TR-17-21; Defense Threat Reduction Agency, Fort Belvoir, VA, USA.
  13. Bewick, B., Rolater, G., Marchand, K., Ziemba, A., Sanai, M. and Laney, C. (2017b), "Fragmentation of solid materials using shock tubes Part 2: First test series in a large-diameter shock tube", DTRA-TR-17-50; Defense Threat Reduction Agency, Fort Belvoir, VA, USA.
  14. Bewick, B., Rolater, G., Marchand, K., Ziemba, A., Sanai, M. and Laney, C. (2018), "Fragmentation of solid materials using shock tubes Part 3: Second test series in a small-diameter shock tube", DTRA-TR-19-3, Defense Threat Reduction Agency, Fort Belvoir, VA, USA.
  15. Bewick, B., Rolater, G., Marchand, K., Ziemba, A., Sanai, M. and Laney, C. (2019), "Fragmentation of solid materials using shock tubes Part 4: Second test series in a large-diameter shock tube", Defense Threat Reduction Agency, Fort Belvoir, VA, USA.
  16. Bischoff, P.H. and Perry, S.H. (1985), "Compressive Strain Rate Effects of Concrete", MRS Online Proceedings Library (OPL), 64, 151. https://doi.org/10.1557/PROC-64-151.
  17. Burnett, S., Gilbert, M., Molyneaux, T., Tyas, A., Hobbs, B. and Beattie, G. (2007), "The response of masonry joints to dynamic tensile loading", Mater. Struct., 40, 517-527. https://doi.org/10.1617/s11527-006-9160-6.
  18. Chapman, A.J. and Walekr, W.F. (1971), Introductory Gas Dynamics, Holt Rinehart and Winston Inc., New York, NY, USA.
  19. Davidson, J.S., Fisher, J.W., Hammons, M.I., Porter, J.R. and Dinan, R.J. (2005), "Failure mechanisms of polymer-reinforced concrete masonry walls subjected to blast", J. Struct. Eng. ASCE, 131, 1194-1205. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:8(1194).
  20. Dennis, S.T., Baylot, J.T. and Woodson, S.C. (2002), "Response of 1/4-scale concrete masonry unit (CMU) walls to blast", J. Eng. Mech., 128(2), 134-142. https://doi.org/10.1061/(ASCE)0733-9399(2002)128:2(134).
  21. Eamon, C.D. (2007), "Reliability of concrete masonry unit walls subjected to explosive loads", J. Struct. Eng., 133, 935-944. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:7(935).
  22. Eamon, C.D., Baylot, J.T. and O'Daniel, J.L. (2004), "Modeling concrete masonry walls subjected to explosive loads", J. Eng. Mech., 130(9), 1098-1106. https://doi.org/10.1061/(ASCE)0733-9399(2004)130:9(1098).
  23. European Committee for Standardization (2003), EN 1052-3 Methods of Test for Masonry Part 3: Determination of Initial Shear Strength, European Committee for Standardization, Brussels, Belgium.
  24. Gaydon, A.G. and Hurle, I.R. (1963), The Shock Tube in High-Temperature Chemical Physics, Reinhold Publishing Corporation, New York, NY, USA.
  25. Groot, C.J.W.P. (1993), Effects of Water on Mortar-Brick Bond, Delft University of Technology, Delft, The Nethetlands.
  26. Grote, D.L., Park, S.W. and Zhou, M. (2001), "Dynamic behavior of concrete at high strain rates and pressures - I experimental characterization", International Journal of Impact Engineering, 25(9), 869-886. https://doi.org/10.1016/S0734-743X(01)00020-3.
  27. Hao, H. (2015), "Numerical modelling of masonry wall response to blast loads", Australian J. Struct. Eng., 10(1), 37-52. https://doi.org/10.1080/13287982.2009.11465031.
  28. Hao, H. and Tarasov, B.G. (2008), "Experimental study of dynamic material properties of clay brick and mortar at different strain rates", Australian J. Struct. Eng., 8(2), 117-132. https://doi.org/10.1080/13287982.2008.11464992.
  29. Hatfield, J.E. and Davidson, J.S. (2022), "Fragmentation and hazard analysis of brittle materials under far-field blast loading", Adv. Struct. Eng., 25(7), 1535-1548. https://doi.org/10.1177/13694332221087339.
  30. Hatfield, J.E., Pezzola, G.L., Walker, R.E., Hoemann, J.M., Stephens, C.S. and Davidson, J.S. (2022a), "Predicting fragment velocity of masonry walls subjected to blast", ASCE Structures Congress, Atlanta, GA, April.
  31. Hatfield, J.E., Pezzola, G.L., Walker, R.E., Stephens, C.S. and Davidson, J.S. (2022b), "Fragment response of unreinforced concrete masonry walls subjected to blast loading", Int. J. Protect. Struct., 13(2), 161-181. https://doi.org/10.1177/20414196221080482.
  32. Hughes, B.P. and Watson. A.J. (1978), "Compressive strength and ultimate strain of concrete under impact loading", Mag. Concrete Res., 30(105), 189-199. https://doi.org/10.1680/macr.1978.30.105.189.
  33. Islam, M.T. and Bindiganavile, V. (2011), "The impact resistance of masonry units bound with fibre reinforced mortars", Constr. Build. Mater., 25(6), 2851-2859. https://doi.org/10.1016/j.conbuildmat.2010.12.049.
  34. Islam, M.T., Chan, R. and Bindiganavile, V. (2012), "Stress rate sensitivity of stone masonry units bound with fibre reinforced hydraulic lime mortar", Mater. Struct., 45, 765-776. https://doi.org/10.1617/s11527-011-9796-8.
  35. John, R. and Shah, S.P. (1987), "Effects of high strength and rate of loading on fracture parameters of concrete", Proceedings of SEM-RILEM International Conference Fracture, Houston, TX, USA, June.
  36. Jukes, P. and Riddington, J.R. (1997), "A review of masonry joint shear strength test methods", Masonry Int., 11(2), 37-43.
  37. Jukes, P. and Riddington, J.R. (1998), "A review of masonry tensile bond strength test methods", Masonry Int., 12(2), 51-57.
  38. Kerlins, V. and Committee, A.H. (1987), "Modes of fracture", Fractography, 1987 Edition, ASM International, Almere, The Netherlands.
  39. Keys, R.A. and Clubley, S.K. (2017a), "Establishing a predictive method for blast induced masonry debris distribution using experimental and numerical methods", Eng. Fail. Anal., 82, 92-91. https://doi.org/10.1016/j.engfailanal.2017.07.017.
  40. Keys, R.A. and Clubley, S.K. (2017b), "Experimental analysis of debris distribution of masonry panels subjected to long duration blast loading", Eng. Struct., 130, 229-241. https://doi.org/10.1016/j.engstruct.2016.10.054.
  41. Livermore Software Technology Corporation (2006), LS-DYNA Theory Manual, Livermore Software Technology Corporation, Livermore, CA, USA.
  42. Lourenco, P.B. (1998), "Experimental and numerical issues in the modelling of the mechanical behaviour of masonry", Structural Analysis of Historical Construction II, Barcelona, Spain. November.
  43. Magallanes, J.M., Morrill, K.B., Crawford, J.E., Oesterle, M.G. and Hegemeir, G.A. (2008), "Finite element models for the analysis and design of CMU walls to blast load", Proceedings of the 80th DDESB Explosives Safety Seminar, Palm Springs, CA, August.
  44. Melander, J.M. and Conway, J.T. (1993), "Compressive strengths and bond strength of portland cement-lime mortars", Masonry: Design and Construction, Problems and Repair, ASTM International, West Conshohocken, PA, USA.
  45. Melander, J.M., Ghosh, S.K., Dubovoy, V.S., Hedstrom, E.G. and Klinger, R.E. (1993), "Flexural bond strength of concrete masonry prisms using masonry cement mortars", Masonry: Design and Construction, Problems and Repair, ASTM International, West Conshohocken, PA, USA.
  46. Mendoza-Puchades, M. (2021), "Masonry brick-to-mortar interface variability, for compressive and tensile strength, under blast actions: Experimental testing, numerical modelling challenges and the application of a framework for the treatment of uncertainties", University of Liverpool, Liverpool, UK.
  47. Oh, B.H. (1987), "Behavior of concrete under dynamic tensile loads", ACI Mater. J., 84(1), 8-13. https://doi.org/10.14359/1787.
  48. Pandey, A.K. and Bisht, R.S. (2014), "Numerical modelling of infilled clay brick masonry under blast loading", Adv. Struct. Eng., 17(4), 591-606. https://doi.org/10.1260/1369-4332.17.4.591.
  49. Pereira, J.M. and Paulo, L.B. (2017), "Experimental characterization of masonry and masonry components at high strain rates", J. Mater. Civil Eng., 29(2), 04016223. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001755.
  50. Pereira, J.M., Dias, A. and Lourenco, P.B. (2013), "Dynamic properties of clay brick at different strain rates", 12th Canadian Masonry Symposium, Vancouver, BC, Canada, June.
  51. Pluijm, R.V.D. (1997), Non-linear behaviour of masonry under tension, Heron, 42(1), 25-54.
  52. Pluijm, R.V.D. (1999), "Out-of-plane bending of masonry - behaviour and strength", Ph.D. Thesis, Eindhoven University of Technology, Eindhoven, The Netherlands.
  53. Rafsanjani, S.H., Lourenco, P.B. and Peixinho, N. (2015), "Dynamic interface model for masonry walls subjected to high strain rate out-of-plane loads", Int. J. Impact Eng., 76, 28-37. https://doi.org/10.1016/j.ijimpeng.2014.09.002.
  54. Rahman, A. and Ueda, T. (2014), "Experimental investigation and numerical modeling of peak shear stress of brick masonry mortar joint under compression", J. Mater. Civil Eng., 26(9), 04014061. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000958.
  55. Rahman, M.A. and Anand, S.C. (1994), "Empirical Mohr-Coulomb failure criterion for concrete block-mortar joints", J. Struct. Eng. ASCE, 120(8), 2408-2422. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:8(2408).
  56. Ross, C.A., Jerome, D.M., Tedesco, J.W. and Mary, L.H. (1996), "Moisture and strain rate effects on concrete strength", ACI Mater. J., 93(3), 293-300. https://doi.org/10.14359/9814.
  57. Ross, C.A., Tedesco, J.W. and Kuennen, S.T. (1995), "Effects of strain rate on concrete strength", ACI Mater. J., 92(1), 37-47. https://doi.org/10.14359/1175.
  58. Ross, C.A., Thompson, P.Y. and Tedesco, J.W. (1989), "Split-Hopkinson pressure-bar tests on concrete and mortar in tension and compression", ACI Mater. J., 86(5), 475-481. https://doi.org/10.14359/2065.
  59. Schneider, J.M., Ramin, M., Stottmeister, A. and Stolz, A. (2020), "Characterization of debris throw from masonry wall sections subjected to blast", Eng. Struct., 203, 109729. https://doi.org/10.1016/j.engstruct.2019.109729.
  60. Shah, S.P. (1985), "Concrete and fiber reinforced concrete subjected to impact loading", MRS Online Proc. Library, 64(1), 181-201. https://doi.org/10.1557/PROC-64-181.
  61. Shi, Y., Wang, N., Li, Z.X. and Ding, Y. (2021), "Experimental studies on the dynamic compressive and tensile strength of clay brick under high strain rates", Constr. Build. Mater., 272, 121908. https://doi.org/10.1016/j.conbuildmat.2020.121908.
  62. Sielicki, P.W. and Lodygowski, T. (2019), "Masonry wall behaviour under explosive loading", Eng. Fail. Anal., 104, 274-291. https://doi.org/10.1016/j.engfailanal.2019.05.030.
  63. Singh, S.B. and Munjal, P. (2017), "Bond strength and compressive stress-strain characteristics of brick masonry", J. Build. Eng., 9, 10-16. https://doi.org/10.1016/j.jobe.2016.11.006.
  64. Soroushian, P., Ki-Bong, C. and Gung, F. (1985), "Tensile strength of concrete at different strain rates", MRS Online Proc. Library, 64, 87. https://doi.org/10.1557/PROC-64-87.
  65. Takeda, J.I. (1985), "Strain rate effects on concrete and reinforcements, and their contributions to structures", MRS Online Proc. Library, 64(1), 15-20. https://doi.org/10.1557/PROC-64-15.
  66. Tedesco, J.W. and Ross, C.A. (1993), "Experimental and numerical analysis of high strain rate splitting-tensile tests", ACI Mater. J., 90(2), 162-169. https://doi.org/10.14359/4013.
  67. TMS (2016), Building Code Requirements and Specification for Masonry Structures (TMS 402/602-16), The Masonry Society, Longmont, CO, USA.
  68. Wang, J., Heath, A. and Walker, P. (2013), "Experimental investigation of brickwork behaviour under shear, compression and flexure", Constr. Build. Mater., 48, 448-456. https://doi.org/10.1016/j.conbuildmat.2013.07.025.
  69. Wang, M., Hao, H., Ding, Y. and Li, Z.X. (2008), "Numerical prediction of statistical masonry wall fragment distribution induced", Trans. Tianjin Univ., 14(6), 409-413. https://doi.org/10.1007/s12209-008-0070-2.
  70. Wang, M., Hao, H., Ding, Y. and Li, Z.X. (2009), "Prediction of fragment size and ejection distance of masonry wall under blast load using homogenized masonry material properties", Int. J. Impact Eng., 36(6), 808-820. https://doi.org/10.1016/j.ijimpeng.2008.11.012.
  71. Watstein, D. (1953), "Effect of straining rate on the compressive strength and elastic properties of concrete", ACI J. Proc., 49(4), 729-744. https://doi.org/10.14359/11850.
  72. Wei, X. and Stewart, M.G. (2010), "Model validation and parametric study on the blast response of unreinforced brick masonry walls", Int. J. Impact Eng., 37(11), 1150-1159. https://doi.org/10.1016/j.ijimpeng.2010.04.003.
  73. Wright, J.K. (1961), Shock Tubes, John Wiley & Sons Inc., New York, NY, USA.
  74. Yon, J.H., Hawkins, N.M. and Albert, S.K. (1992), "Strain-rate sensitivity of concrete mechanical properties", ACI Mater. J., 89(2), 146-153. https://doi.org/10.14359/2223.
  75. Zhang, X., Chiu, Y.W., Hao, H., Hsieh, A., Salter, N. and Cui, J. (2018), "Dynamic compressive material properties of clay bricks at different strain rates", Constr. Build. Mater., 192, 754-767. https://doi.org/10.1016/j.conbuildmat.2018.10.150.
  76. Zhou, X.Q. and Hao, H. (2009), "Mesoscale modelling and analysis of damage and fragmentation of concrete slab under contact detonation", Int. J. Impact Eng., 36(12), 1315-1326. https://doi.org/10.1016/j.ijimpeng.2009.02.010.