DOI QR코드

DOI QR Code

Behavior of simple precast high-strength concrete beams connected in the maximum bending moment zone using steel extended endplate connections

  • Magdy I. Salama (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University) ;
  • Jong Wan Hu (Department of Civil and Environmental Engineering, Incheon National University) ;
  • Ahmed Almaadawy (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University) ;
  • Ahmed Hamoda (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University) ;
  • Basem O. Rageh (Civil Engineering Department., Delta Higher Institute for Engineering and Technology) ;
  • Galal Elsamak (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University)
  • Received : 2021.04.26
  • Accepted : 2023.10.31
  • Published : 2024.03.25

Abstract

This paper presents an experimental and numerical study to investigate the behavior of the precast segmental concrete beams (PSCBs) utilizing high-strength concrete (HSC) connected in the zone of the maximum bending moment using steel extended endplate connections (EECs). The experimental study consisted of five beams as follows: The first beam was the control beam for comparison, which was an unconnected one-piece beam made of HSC. The other four other beams consisted of two identical pieces of precast concrete. An important point to be noted is that at the end of each piece, a steel plate was used with a thickness of 10 mm. Moreover, this steel plate was welded to the lower and upper reinforcing bars of the beam. Furthermore, the steel plate was made to connect the two pieces using the technique of EECs. Several variables were taken in these four beams, whether from the shape of the connection or enhancing the behavior of the connection using the post-tensioning technique. EECs without stiffeners were used for some of the tested beams. The behavior of these connections was improved using stiffeners and shear bolts. To get accurate results, a comparison was made between the behaviors of the five beams. Another important point to be noted is that Abaqus and SAP2000 programs were used to investigate the behavior of PSCBs and to ensure the accuracy of the modeling process which showed a good agreement with the experimental results. Additionally, the simplified modeling using SAP2000 was able to model the nonlinear behavior of PSCBs connected using steel EECs. It was found that the steel pre-tensioned bolted EECs, reinforced with steel stiffeners and shear anchors, could be used to connect the precast HSC segmental beams via the internal pre-stressing technique.

Keywords

Acknowledgement

This work is supported by the Korea Agency for Infrastructure Technology Advancement (KAIA) grant funded by the Ministry of Land, Infrastructure and Transport (Grant 21CFRP-C163381-01).

References

  1. Afefy, H.M., Abdel-Aziz, M.A., Kassem, N.M. and Mahmoud, M.H. (2020), "Improving flexural performance of post-tensioned pre-cast pre-stressed RC segmental T-beams", Structures, 24, 304-316. https://doi.org/10.1016/j.istruc.2020.01.027.
  2. Ahmed, G.H. and Aziz, O.Q. (2020), "Stresses, deformations and damages of various joints in precast concrete segmental box girder bridges subjected to direct shear loading", Eng. Struct., 206, 110151. https://doi.org/10.1016/j.engstruct.2019.110151.
  3. Akgonen, A.I., Yorgun, C. and Vatansever, C. (2015), "Cyclic behavior of extended end-plate connections with European steel shapes", Steel Compos. Struct., 19, 1185-1201. https://doi.org/10.12989/scs.2015.19.5.1185
  4. Braham, M. and Jaspart, J.-P. (2004), "Is it safe to design a building structure with simple joints, when they are known to exhibit a semi-rigid behaviour?", J. Constr. Steel Res., 60(3-5), 713-723. https://doi.org/https://doi.org/10.1016/S0143-974X(03)00138-X.
  5. Code, P. (2005), Eurocode 2: Design of Concrete Structures-Part 1-1: General Rules and Rules for Buildings. Br. Stand. Inst. Lond.
  6. Coelho, A.G., da Silva, L.S. and Bijlaard, F.S. (2006), "Ductility analysis of bolted extended end plate beam-to-column connections in the framework of the component method", Steel Compos. Struct., 6(1), 33. https://doi.org/https://doi.org/10.12989/scs.2006.6.1.033.
  7. Computers Structures I. (2011), CSI Analysis Reference Manual for SAP2000, ETABS® SAFE® CSiBridgeTM.
  8. Da Silva, J., De Lima, L., Vellasco, P.d.S., De Andrade, S. and De Castro, R. (2008), "Nonlinear dynamic analysis of steel portal frames with semi-rigid connections", Eng. Struct., 30(9), 2566-2579. https://doi.org/https://doi.org/10.1016/j.engstruct.2008.02.011.
  9. Dessouki, A.K., Youssef, A.H. and Ibrahim, M.M. (2013), "Behavior of I-beam bolted extended end-plate moment connections", Ain Shams Eng. J., 4, 685-699. https://doi.org/10.1016/j.asej.2013.03.004.
  10. Duval, A., Al-akhras, H., Maurin, F., Elguedj, T., Duval, A., Al-akhras, H., Maurin, F. and Elguedj, T. (2014), Abaqus/CAE 6.14 User's Manual, Dassault Systemes Inc.
  11. Engineers, A.S. of C. (2014), Seismic Evaluation and Retrofit of Existing Buildings, American Society of Civil Engineers.
  12. FEMA 356, F.E. (2000), Prestandard and Commentary for the Seismic Rehabilitation of Buildings, Fed. Emerg. Manag. Agency Wash. DC.
  13. Jaspart, J.-P. (1988), "Extending of the merchant-rankine formula for the assessment of the ultimate load of frames with semi-rigid joints", J. Constr. Steel Res., 11(4), 283-312. https://doi.org/https://doi.org/10.1016/0143-974X(88)90097-1.
  14. Jaspart, J.-P. (2000), "General report: session on connections", J. Constr. Steel Res., 55(1-3), 69-89. https://doi.org/https://doi.org/10.1016/S0143-974X(99)00078-4.
  15. Jaspart, J.-P. and Maquoi, R. (1990), "Guidelines for the design of braced frames with semi-rigid connections", J. Constr. Steel Res., 16(10), https://doi.org/https://doi.org/10.1016/0143-974X(90)90033-D.
  16. Jiang, H., Cao, Q., Liu, A., Wang, T. and Qiu, Y. (2016), "Flexural behavior of precast concrete segmental beams with hybrid tendons and dry joints", Constr. Build. Mater., 110, 1-7. https://doi.org/10.1016/j.conbuildmat.2016.02.003.
  17. Jiang, H., Fang, H., Wu, J., Fang, Z., Fang, S. and Chen, G. (2022), "Push-out tests on demountable high-strength friction-grip bolt shear connectors in steel-precast UHPC composite beams for accelerated bridge construction", Steel Compos. Struct., 45, 797-818.
  18. Keikha, H. and Mofid, M. (2017), "On the assessment of a new steel bolted flush end-plate beam splice connection", Sci. Iran., 24, 1735-1750. https://doi.org/10.24200/sci.2017.4266.
  19. Khaloo, A.R. and Parastesh, H. (2003), "Cyclic loading response of simple moment-resisting precast concrete beam-column connection", Struct. J., 100, 440-445. https://doi.org/10.14359/12652.
  20. Khoo, J.H., Li, B. and Yip, W.K. (2006), "Tests on precast concrete frames with connections constructed away from column faces", ACI Mater. J., 103(1), 18.
  21. Kollipara, V.R. and Gunneswara Rao, T.D. (2019), "Experimental and analytical study for plastic moment capacity of beam-beam splice connection", Int. J. Steel Struct., 19, 1202-1208. https://doi.org/10.1007/s13296-018-00200-4.
  22. Le, T.D., Pham, T.M., Hao, H. and Hao, Y. (2018), "Flexural behaviour of precast segmental concrete beams internally prestressed with unbonded CFRP tendons under four-point loading", Eng. Struct., 168, 371-383. https://doi.org/10.1016/j.engstruct.2018.04.068.
  23. Li, D., Uy, B., Mo, J. and Thai, H.-T. (2022), "Behaviour and design of bolted endplate joints between composite walls and steel beams", Steel Compos. Struct., 44, 33-47.
  24. Ousalem, H., Ishikawa, Y., Kimura, H., Kusaka, T., Yanagisawa, N. and Okamoto, K. (2009), "Seismic performance and flexural stiffness variation of assembled precast high-strength concrete beam jointed at mid-span using transverse bolts", J. Adv. Concr. Technol., 7, 205-216. https://doi.org/10.3151/jact.7.205
  25. Rahman, A.B.A., Leong, D.C.P., Saim, A.A. and Osman, M.H. (2006), "Hybrid beam-to-column connections for precast concrete frames", In Proceedings of the 6th Asia-Pacific Structural Engineering and Construction Conference, Kuala Lumpur, Malaysia, September.
  26. Shi, G., Shi, Y., Wang, Y. and Bradford, M.A. (2008), "Numerical simulation of steel pretensioned bolted end-plate connections of different types and details", Eng. Struct., 30, 2677-2686. https://doi.org/10.1016/j.engstruct.2008.02.013.
  27. Shi, Y., Shi, G. and Wang, Y. (2007), "Experimental and theoretical analysis of the moment-rotation behaviour of stiffened extended end-plate connections", J. Constr. Steel Res., 63, 1279-1293. https://doi.org/10.1016/j.jcsr.2006.11.008.
  28. Stone, W.C., Cheok, G.S. and Stanton, J.F. (1995), "Performance of hybrid moment-resisting precast beam-column concrete connections subjected to cyclic loading", Struct. J., 92, 229-249. https://doi.org/10.14359/1145.
  29. Weynand, K., Jaspart, J.-P. and Steenhuis, M. (1998), "Economy studies of steel building frames with semirigid joints", J. Constr. Steel Res., 46(1-3). https://doi.org/https://doi.org/10.1016/S0143-974X(98)00045-5